0011200314 MOLEX11 | Alldatasheet

Document overview

  • Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
  • PDF pages: 4

Technical content

OPERATION AND SERVICE INSTRUCTIONS - MOLEX - ARBOR TERMINATOR FOR .156 SPACED I.D. CONNECTORS AM-7223-126 (11-20-0314)

DESCRIPTION

The arbor temninator is a small bench mounted press containing fixtures to assemble ribbon cable to pre-loaded I.D. connectors. It is low cost terminator intended for medium volume of assembly, Rates are determined by operator efficiency since the operator controls all steps in the operation; loading a connector, positioning pre- cut cable, lowering the press ram, and removing a completed assembly. PRODUCT SPECIFICATIONS : Pre-notched cable with conductors on .156 spacing can be terminated into the follow- ing housings; 7674, 7675 and 7223. Connector circuit size can vary from 2 to 16 circuits. TO OPERATE 1. Slide a connector into the pocket in the lower fixture block. Orientate the connector so the exposed terminals and wire slots face up and the housing rib is on the left side of the connector. Push the connector to the rear wall of the pocket whereaspring loaded ball plunger will engage an opening in the connector side to position the housing. 2. Locate the ribbon cable with its edge along the guide bar at the rear, The pre-notched area of the cable is visually lined up over the connector. For "daisy chain" terminations, the notch openings is centered across the connector width. For cable end termination, the pre-cut cable is moved from left to right until the wire ends lay across the connector. -l-

  1. Holding the cable in position, depress the arbor handle until the downward. motion is stopped by the displacement adjusting screw. Release handle and pull cable assembly forward out of the fixture holding block. TO ADJUST THE ARBOR TERMINATOR 1. ‘The cable should be pushed into the connector until the cable insulation just touches or is .010 inches (0.25) above the bottom of the housing wire slot. To adjust this displacement depth, turn the stop screw located in the block fasten- ed to the top of the arbor ram. 2. Support rods on the rear cable guide can be relocated to provide maximum contact for the cable without interfering with connectors already assembled to the cable. 3. The displacement teeth should enter a connector without touching the contact. If realignment is needed, move the lower fixture block by loosening the two screws holding the block to the arbor, Retighten lower block with the ram down and engaged in connector housing. MAINTENANCE Lubricate the arbor press monthly by introducing a small quantity of grease through the grease fitting in the handle support. Spare parts are not normally supplied. Should a problem or question arise, please contact the factory. Molex, Inc. Application Tooling Department

2222 Wellington Court

Lisle, IL 60532 312/969-4550

wn Sheet 1 of 1 , ‘Tite: ___ Main Assy 7223 HSG. - 16 CIRCUITS AM7223-126 11-20-0314 No. Size AM7223-126 D Assembly - Arbor Terminator

1 AM4700-25 D 1 Lever Press Modification cM 11-21-0698

2 AM7223-52 A 1 Press Chuck 11-21-1627

4 -127 c 1 L.E. Insertion Blade 16 Ckt. 11-21-2407 5 -128 c 1 R.H. Insertion Blade 16 Ckt. 11-21-2408 6 -129 A 1 Left Plate ° 11-21-2409 7 -130 A 1 Right Plate 11-21-2410 9 ~58 A 1 ‘Cable Guide Bar 11-21-1632 10 -59 A 2 Cable Support 11-21-1633 11 -43 . 1 Spring Plunger, Vlier $-51 11-21-1634 12 4968 1 Molex Serial Tag c 11-17-0676 13° AM7223-131 A 1 Base Block 11-21-2411 14 -44 2 Comp. Spring Assoc. #C0975-092 c 11-21-1636 -3000S 15 -41 1 Arbor Down Stop - Janesville c 11-21-1245 - 16 -42 A 1 Clamp Bar - Chuck 11-21-1637

17 AM4700-40 1 Ball Knob Reids #B-32 c 11-21-4970

18 AM7223-45 A 1 Stop Screw 11-21-1638

19 AM4700-26 B 1 Base Plate 11-10-1050

  1. 2 5/16-18 x 3/4 BHCS c 21 1 3/16 Dia. x 7/8 Lg. Dowel c 22 1 1/4-20 x 7/8 Lg. Soc. HSS c 23 8 #10-32 x 1" Soc. HSS c 24 2 #8-32 x 1 1/4" Soc. HCS c 25 1 #6-32 x 3/8 Full Dog Point SS Cc . 26 2 1/8 Drive Screw c 27 « 4 1/8 Dia. x 3/4 Lg. Dowel c 28 2 #8-32 x 5/8 Lg. SHCS . c 29° AM7223-133 A 1 End Wall Retainer 11-21-5517 30 -134 A 1 Floating Retainer 11-21-5518 “ga -135 A 1 Floating Retainer Mtg. Block 11-21-5519 CoRR REURNG CODES CH=-CONMERCIAL PART MODIFIED CO=CUSTOMER ORDER N=SUPPLIED BY MOLEX P=PERISHABLE TOOLING R=REPLACENEST PART S=MADE IN SHOP SS=SEE SUPPLEMENT SHEET SE=SEE EXGIXERRISG A

: B® 2 B® OP Ry ie ~ 4 ‘ om de Ree jz a}. x : f . Kee A # aS | Ma a PP eBags a\\¢ ar r pes) | FRAP T ot eget | “(SEE FR ee ee ee ci oe gt Se BS SS ate EG is Bone Diag Ma emt