DATASHEET SEARCH SITE | WWW.ALLDATASHEET.COM

Document overview

  • Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
  • PDF pages: 4

Technical content

6 Watt | DC-DC Converter

www.aimtec.com Tel: +1 514 620 2722 Toll free: + 1 888 9 AIMTEC (924 6832) F 051e R13.A 1 of 4 North America only Picture coming soon FEATURES:

  • Wide 4:1 Input Voltage Range • Operating Temperature -40ºC to +85ºC
  • High efficiency up to 88% • Output Over Voltage protection
  • 1500 VDC Isolation • Continuous Short Circuit Protection
  • Over Current Protection • Input Under voltage Protection
  • No load consumption ≤ 0.12W Models Single output Model Input Voltage (V) Output Voltage (V) Output Current max (mA) Isolation (VDC) Max Capacitive Load(uF) Efficiency (%) AM6CW-2403S-NZ 9-36 3.3 1500 1500 1800 79 AM6CW-2405S-NZ 9-36 5 1200 1500 1000 83 AM6CW-2409S-NZ 9-36 9 667 1500 680 85 AM6CW-2412S-NZ 9-36 12 500 1500 470 87 AM6CW-2415S-NZ 9-36 15 400 1500 220 88 AM6CW-2424S-NZ 9-36 24 250 1500 100 88 AM6CW-4803S-NZ 18-75 3.3 1500 1500 1800 79 AM6CW-4805S-NZ 18-75 5 1200 1500 1000 83 AM6CW-4812S-NZ 18-75 12 500 1500 470 87 AM6CW-4815S-NZ 18-75 15 400 1500 220 88 AM6CW-4824S-NZ 18-75 24 250 1500 100 88 AM6CW-11005S-NZ 40-160 5 1200 1500 1000 81 AM6CW-11012S-NZ 40-160 12 500 1500 100 83 AM6CW-11015S-NZ 40-160 15 400 1500 100 85 AM6CW-11024S-NZ 40-160 24 250 1500 47 85 Models Dual output Model Input Voltage (V) Output Voltage (V) Output Current max (mA) Isolation (VDC) Max Capacitive Load(uF) Efficiency (%) AM6CW-2405D-NZ 9-36 ±5 ±600 1500 470 83 AM6CW-2412D-NZ 9-36 ±12 ±250 1500 100 87 AM6CW-2415D-NZ 9-36 ±15 ±200 1500 100 88 AM6CW-2424D-NZ 9-36 ±24 ±125 1500 100 88 AM6CW-4805D-NZ 18-75 ±5 ±600 1500 470 83 AM6CW-4812D-NZ 18-75 ±12 ±250 1500 100 87 AM6CW-4815D-NZ 18-75 ±15 ±200 1500 100 88 AM6CW-4824D-NZ 18-75 ±24 ±125 1500 100 88 NOTE: All specifications in this datasheet are measured at an ambient temperature of 25°C, humidity<75%, nominal input voltage and at rated output load unless otherwise specified.

www.aimtec.com Tel: +1 514 620 2722 Toll free: + 1 888 9 AIMTEC (924 6832) F 051e R13.A 2 of 4 North America only Input Specifications Parameters Nominal Typical Maximum Units Voltage range 110 9-36 18-75 40-160 VDC Filter Pi Absolute Maximum Rating (100ms) 110 -0.7 - 50 -0.7 - 100 -0.7 - 180 VDC No Load Input Current 110 mA Input reflected current 20 mA Input Under voltage turn off* 24 6.5

15.5 VDC

*24 & 48V input models only. Isolation Specifications Parameters Conditions Typical Maximum Units Tested I/O voltage 60 sec, <1mA 1500 VDC Resistance 500VDC >1000 MOhm Capacitance 1000 pF Output Specifications Parameters Conditions Typical Maximum Units Voltage accuracy ±2 % Voltage balance (Dual Output Models) Balanced Load ±1.5 % Over voltage protection 110-160 % of Vout Over current protection 24 & 48V input models only 110-190 % of Iout Short Circuit protection Continuous Short circuit restart Auto-Recovery Line voltage regulation (Single) Full load, LL to HL ±0.5 % of Vin Line voltage regulation (Dual) Full load, LL to HL ±1 % of Vin Load voltage regulation (Single) 5% to 100% load ±1 % Load voltage regulation (Dual) 5% to 100% load ±1.5 % Cross Regulation (Dual Output Models) 25% load on one output - 100% load on second load ±5 % Temperature coefficient 100% load ±0.03 %/oC Ripple & Noise 100 mV p-p Transient recovery time 25% load step change 1 mS Transient recovery deviation 25% load step change ±8 % General Specifications Parameters Conditions Typical Maximum Units Switching frequency 100% load 300 KHz Operating temperature Derating above 71°C -40 to +85 oC Storage temperature -55 to +125 oC Maximum case temperature 100 oC Cooling Free air convection Humidity 95 % RH Case material Aluminum Alloy Weight 14 g Dimensions (L x W x H) 1 x 1 x 0.46 inches 25.40 x 25.40 x 11.70 mm MTBF >1,000,000 hours (MIL-HDBK -217F, Ground Benign, t=+25 o Maximum soldering temperature 1.5mm from case for 10 sec 300 oC

www.aimtec.com Tel: +1 514 620 2722 Toll free: + 1 888 9 AIMTEC (924 6832) F 051e R13.A 3 of 4 North America only Environmental Specifications Parameters Vibration Test mode 5-150Hz Acceleration 2G, 30min one cycle, every axis tested Displacement 7.5mm Safety Specifications Parameters Standards Meets EN60950-1 EN 55022, class B (with the recommended EMC circuit) Pin Out Specifications Dimensions Pin Single Dual 1 +V Input +V Input 2 -V Input -V Input 3 +V Output +V Output

4 No pin Common

  • 40 - 20 0 20 40 60 80 100 100 Safe Operating Area Output Power (%) Ambient Temperature º C Free Air Convection 71º C Notes: All dimensions are typical in millimeters (inches). Case Tolerance ±0.25 (±0.01) Pin diameter tolerance ±0.1 (±0.004) Pin height tolerance ±0.5 (±0.02) 25.40 (1.00) 2.54 (0.10) 20.32 (0.80) 2.54 (0.10) 10.16 (0.40) 5.08 (0.20) 2.54 (0.10)10.16 (0.40) 10.16 (0.40) 25.40 (1.00)11.70 (0.46) Printed Face 1.00 (0.39) Top View Side View 2.54 (0.10) Input Input 3 4 5 +V Output Common -V Output Bottom View 4.10 (0.16)

www.aimtec.com Tel: +1 514 620 2722 Toll free: + 1 888 9 AIMTEC (924 6832) F 051e R13.A 4 of 4 North America only Recommended EMC Circuits For 110V input models AM6CW-NZ 10mH 10mH +Vin -Vin +Vo -Vo CX 0.68uF CX 0.68uF CX 0.68uF 1nF/2KV 1nF/2KV For 24V and 48V Input models 24V input 48V input MOV S14K35 S14K60 C1 330µF/50V 330µF/100V C2 1µF/50V 1µF/100V C3 10µF/50V 10µF/100V NOTE: 1. Datasheets are updated as needed and as such, specifications are subject to change without notice. Once printed or downloaded, datasheets are no longer controlled by Aimtec; refer to www.aimtec.com for the most current product specifications. 2. Product labels shown, including safety agency certifications on labels, may vary based on the date manufactured. 3. Mechanical drawings and specifications are for reference only. 4. All specifications are measured at an ambient temperature of 25°C, humidity<75%, nominal input voltage and at rated output load unless otherwise specified. 5. Aimtec may not have conducted destructive testing or chemical analysis on all internal components and chemicals at the time of publishing this document. CAS numbers and other limited information are considered proprietary and may not be available for release. 6. This product is not designed for use in critical life support systems, equipment used in hazardous environments, nuclear control systems or other such applications which necessitate DC-DC Converter +Vin -Vin +Vo -Vo CY1 1nF/2KV CY2 1nF/2KV LDM 4.7µH MOV