AGN200A09

AGN20003 NAIS | Alldatasheet

Document overview

• Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
• PDF pages: 4

Technical content

5.70–0.3 .224–.01210.60–0.3 .417–.012 9.00–0.3 .354–.012 5.70–0.3 .224–.01210.60–0.3 .417–.012 Max.10.00 .394 mm inch

FEATURES

• Compact slim body saves space Thanks to the small surface area of 5.7 mm 10.6 mm .224 inch .417 inch and low height of 9.0 mm .354 inch, the pack- aging density can be increased to allow for much smaller designs.
• Outstanding surge resistance. Surge withstand between open contacts: 1,500 V 10 160 m s (FCC part 68) Surge withstand between contacts and coil: 2,500 V 2 m s (Bellcore)
• The use of twin crossbar contacts en- sures high contact reliability. AgPd contact is used because of its good sulfide resistance. Adopting low-gas molding material. Coil assembly molding technology which avoids generating vola- tile gas from coil.
• Increased packaging density Due to highly efficient magnetic circuit de- sign, leakage flux is reduced and changes in electrical characteristics from compo- nents being mounted close-together are minimized. This all means a packaging density higher than ever before.
• Nominal operating power: 140 mW
• Outstanding vibration and shock re- sistance. Functional shock resistance: 750 m/s {75G} Destructive shock resistance: 1,000 m/s {100G} Functional vibration resistance: 10 to 55 Hz (at double amplitude of 3.3 mm .130 inch) Destructive vibration resistance: 10 to 55 Hz (at double amplitude of 5 mm .197 inch) SPECIFICATIONS Contact Remarks: * Specifications will vary with foreign standards certification ratings. Measurement at same location as "Initial breakdown voltage" section. Detection current: 10mA. Nominal voltage applied to the coil, excluding contact bounce time. By resistive method, nominal voltage applied to the coil; contact carrying current: 1 A. Half-wave pulse of sine wave: 6 ms; detection time: 10 m Half-wave pulse of sine wave: 6 ms. Detection time: 10 m Refer to 5. Conditions for operation, transport and storage mentioned in AMBIENT ENVIRONMENT (Page 61) Characteristics Notes: g

1 This value can change due to the switching frequency, environmental conditions,

and desired reliability level, therefore it is recommended to check this with the actual load. g

2 The upper limit for the ambient temperature is the maximum temperature that

can satisfy the coil temperature rise. Under the packing condition, allowable temperature range is from –40 to +70 C –40 to +158 Arrangement 2 Form C Initial contact resistance, max. (By voltage drop 6 V DC 1A ) 100 m W Contact material Stationary: AgPd+Au clad Movable: AgPd Rating Nominal switching capacity (resistive load)

1 A 30 V DC

0.3 A 125 V AC

Max. switching power (resistive load) 30 W, 37.5 V A Max. switching voltage 110 V DC, 125 V AC Max. switching current 1 A Min. switching capacity g 1 10 m A 10 mV DC Nominal operating power Single side stable 140mW (1.5 to 12 V DC) 230mW (24 V DC) 1 coil latching 100mW (1.5 to 12 V DC) 120mW (24 V DC) Expected life (min. operations) Mechanical (at 180 cpm) 5 Electrical (at 20 cpm) Initial insulation resistance* Min. 1,000M W (at 500V DC) Initial breakdown voltage* Between open contacts 750 Vrms for 1min. Between contact sets 1,000 Vrms for 1min. Between contacts and coil 1,500 Vrms for 1min. Initial surge voltage Between open contacts (10 160 m s) 1,500 V (FCC Part 68) Between contacts and coil m s) 2,500 V (Bellcore) Operate time [Set time]* (at 20 C) Max. 4 ms (Approx. 2 ms) [Max. 4 ms (Approx. 2 ms)] Release time (without diode) [Reset time]* (at 20 Max. 4 ms (Approx. 1 ms) [Max. 4 ms (Approx. 2 ms)] Temperature rise* (at 20 C) Max. 50 C Shock resistance Functional* Min. 750 m/s {75G] Destructive* Min. 1,000 m/s {100G] Vibration resistance Functional* 10 to 55 Hz at double amplitude of 3.3 mm Destructive 10 to 55 Hz at double amplitude of 5 mm Conditions for opera- tion, transport and storage* (Not freezing and con- densing at low tem- perature) Ambient temperature g –40 C to 85 C –40 F to 185 F Humidity 5 to 85% R.H. Unit weight Approx. 1 g .035 oz TESTING

• Telephone exchange, transmission equipment
• Communications devices
• Measurement devices
• Home appliances, and audio/visual equipment
• Handheld and portable products

ORDERING INFORMATION

200A Z 1HEx. AGN Contact arrangement Terminal shapeOperating function Packing styleCoil voltage (DC) Nil: Standard PC board terminal A: Surface-mount terminal A type S: Surface-mount terminal S type 2: 2 Form C 0: Single side stable 1: 1 coil latching Type of operation 0: Standard type (B.B.M.) Nil: Tube packing Tape and reel packing (piked from 5/6/7/8 pin side) 1H: 1.5V 03 : 3V 4H: 4.5V : 6V 09 : 9V 12 : 12V 24 : 24V Note: Tape and reel packing symbol “-Z” is not marked on the relay. “X” type tape and reel packing (picked from 1/2/3/4-pin side) is also available. Suffix “X” instead of “Z”. TYPES AND COIL DATA (at 20 C 68 (1) Standard PC board terminal 1) Standard packing: 50 pcs. in an inner package (tube); 1,000 pcs. in an outer package 2) Specified value of pick-up, drop-out, set and reset voltage is with the condition of square wave coil pulse. (2) Surface-mount terminal m : For each surface-mounted terminal variation, input the following letter. A type: A, S type: S 1) Standard packing: 50 pcs.(tube), 500pcs. (tape and reel)in an inner package; 1,000 pcs. in an outer package 2) Specified value of pick-up, drop-out, set and reset voltage is with the condition of square wave coil pulse. Operating Function Part No. Coil Rating, V DC Pick-up volt- age, V DC (max.) (initial) Drop-out voltage, V DC (min.) (initial) Nominal operating current, mA ( 10%) Coil resistance, W 10%) Nominal operating power, mW Max. allowable voltage, V DC Standard PC board terminal Single side stable AGN2004H 4.5 3.38 0.45 31 145 140 6.75 AGN20006 6 4.5 0.6 23.3 257 140 9 AGN20009 9 6.75 0.9 15.5 579 140 13.5 AGN20012 12 9 1.2 11.7 1,028 140 18 AGN20024 24 18 2.4 9.6 2,504 230 28.8 Operating Function Part No. Coil Rating, V DC Set voltage, V DC (max.) (initial) Reset voltage, V DC (max.) (initial) Nominal operating current, mA ( 10%) Coil resistance, W 10%) Nominal operating power, mW Max. allowable voltage, V DC Standard PC board terminal 1 coil latching AGN21003 3 2.25 2.25 33.3 90 100 4.5 AGN21006 6 4.5 4.5 16.7 360 100 9 AGN21009 9 6.75 6.75 11.1 810 100 13.5 AGN21012 12 9 9 8.3 1,440 100 18 AGN21024 24 18 18 5.0 4,800 120 36 Operating Function Part No. Coil Rating, V DC Pick-up voltage, V DC (max.) (initial) Drop-out voltage, V DC (min.) (initial) Nominal operating current, mA ( 10%) Coil resistance, W 10%) Nominal operating power, mW Max. allowable voltage, V DC Tube packing Tape and reel packing Single side stable AGN200 m 1H AGN200 m AGN200 m

03 AGN200

m AGN200 m 4H AGN200 m 4HZ 4.5 3.38 0.45 31 145 140 6.75 AGN200 m

06 AGN200

m 06Z 6 4.5 0.6 23.3 257 140 9 AGN200 m

09 AGN200

m 09Z 9 6.75 0.9 15.5 579 140 13.5 AGN200 m

12 AGN200

m 12Z 12 9 1.2 11.7 1,028 140 18 AGN200 m

24 AGN200

m 24Z 24 18 2.4 9.6 2,504 230 28.8

m : For each surface-mounted terminal variation, input the following letter. A type: A, S type: S 1) Standard packing: 50 pcs.(tube), 500pcs. (tape and reel)in an inner package; 1,000 pcs. in an outer package 2) Specified value of pick-up, drop-out, set and reset voltage is with the condition of square wave coil pulse. Operating Function Part No. Coil Rating, V DC Set voltage, V DC (max.) (initial) Reset voltage, V DC (max.) (initial) Nominal operating current, mA ( 10%) Coil resistance, W 10%) Nominal operating power, mW Max. allowable voltage, V DC Tube packing Tape and reel packing 1 coil latching AGN210 m 1H AGN210 m AGN210 m

03 AGN210

m 03Z 3 2.25 2.25 33.3 90 100 4.5 AGN210 m 4H AGN210 m AGN210 m

06 AGN210

m 06Z 6 4.5 4.5 16.7 360 100 9 AGN210 m

09 AGN210

m 09Z 9 6.75 6.75 11.1 810 100 13.5 AGN210 m

12 AGN210

m 12Z 12 9 9 8.3 1,440 100 18 AGN210 m

24 AGN210

m 24Z 24 18 18 5.0 4,800 120 36 DIMENSIONS 1. PC board terminal 10.60–0.3 .417–.012 5.70–0.3 .224–.012 0.40–0.1 .016–.004 (1.50) (.059) 2.20–0.15 .126–.006 0.25–0.1 .010–.004 3.20–0.15 .126–.006 3.50–0.3 .138–.012 (0.50) (.020) 9.00–0.3 .354–.012 PC board pattern Tolerance: 0.1 .004 3.20 .126 2.20 .087 7.60 .299 3.20 .126 8-0.85 dia. 8-.033 dia Schematic (Bottom view) Single side stable (Deenergized condition) 1 coil latching (Reset condition) Direction indication 8 765 1 234 Direction indication mm inch 2. Surface-mount terminal 1) A type 10.60–0.3 .417–.012 5.70–0.3 .224–.012 0.40–0.1 .016–.004 (1.50) (.059) 3.20–0.15 .126–.006 3.20–0.15 .126–.006 0.25–0.1 .010–.004 2.20–0.15 .087–.006 7.40–0.3 .291–.012 (0.50) (.020)9.00–0.3 .354–.012 Max. 10.00 .394 Suggested mounting pad Tolerance: –0.1 –.004 2.20 .087 3.20 .126 5.30 .209 3.10 .122 0.80 .031 1) S type 10.60–0.3 .417–.012 5.70–0.3 .224–.012 3.20–0.15 .126–.0060.40–0.1 .016–.004 (1.50) (.059) 0.25–0.1 .010–.004 3.20–0.15 .126–.006 2.20–0.15 .087–.006 5.70–0.3 .224–.012 (0.50) (.020)9.00–0.3 .354–.012 Max. 10.00 .394 Suggested mounting pad Tolerance: –0.1 –.004 2.20 .087 3.20 .126 4.45 .175 2.25 .089 0.80 .031 Schematic (Top view) Single side stable (Deenergized condition) 1 coil latcing (Reset condition) Direction indication 1 234 8 765 Direction indication 5678 213 4 REFERENCE DATA 1. Max. switching capacity 2. Life curve 30 100 Contact voltage, V 1.0 0.3 DC resistive load AC resistive load Switching current, A Switching current, A No. of operations, · 104 100 DC 30V resistive load AC 125V resistive load

1. Coil operating power 1) As a general rule, only a pure DC pow- er supply should be used for the coil drive. 2) To ensure proper operation, the voltage applied to both terminals of the coil should be –5% (at 20°C 68°F) the rated operating voltage of the coil. Also, be aware that the pick-up and drop-out voltages will fluctu- ate depending on the ambient tempera- ture and operating conditions. 3) The ripple factor for the voltage applied to the coil should be less than 5%. 4) For set and reset latching relays, the rated operating voltage should be applied to the coil for 10 ms or more. 2. Coil connection When connecting coils, refer to the wiring diagram to prevent mis-operation or mal- function. 3. External magnetic field Since GN relays are highly sensitive po- larized relays, their characteristics will be affected by a strong external magnetic field. Avoid using the relay under that con- ditions. 4. Cleaning In automatic cleaning, cleaning with the boiling method is recommended. Avoid ul- trasonic cleaning which subjects the relay to high frequency vibrations. It may cause the contacts to stick. lt is recommended that a fluorinated hy- drocarbon or other alcoholic solvent be used. 5. Packing style 1) The relay is packed in a tube with the relay orientation mark on the left side, as shown in the figure below. 2) Tape and reel packing (A type) (1)-1 Tape dimensions mm inch (S type) (1)-2 Tape dimensions (2) Dimensions of plastic peel mm inch 6. Automatic insertion To maintain the internal function of the relay, the chucking pressure should not exceed the values below. Chucking pressure in the direction A:

4.9 N {500gf} or less

Chucking pressure in the direction B:

9.8 N {1 kgf} or less

Chucking pressure in the direction C: Please chuck the portion. Avoid chucking the center of the relay. In addition, excessive chucking pressure to the pinpoint of the relay should be avoided. Orientation (indicates PIN No.1)stripe Stopper (green) Stopper (red) Relay polarity bar (Z type) Tape coming out direction General tolerance –0.1 mm .004 inch 4.00 .157 1.75 .0690.40 .016 10.70–0.2 .421–.008 2.00 .079 2.00dia .079dia GN relays 16.00 .630 8.00 .315 11.50 .453 24.00–0.3 .945–.01211.10 .437 1.50+0.1 0 dia .059+.004 0 dia Relay polarity bar (Z type) Tape coming out direction General tolerance –0.1 mm .004 inch 1.50+0.1 0 dia .059+.004 0 dia 2.0dia .079dia 4.00 .157 1.75 .069 10.70–0.2 .421–.008 0.40 .016 2.00 .079 GN relays 16.00 .630 6.3 .248 11.50 .453 11.10 .437 24.00–0.3 .945–.012 21–0.8 dia. .827–.031 dia. 13–0.2 dia. .512–.008 dia. 24.4 .961 +.079 100–1 dia. 3.937–.039 dia. 2.0–0.2 .079–.008 370–2 dia. 14.567–.079 dia. 2.0–0.5 .079–.020 A C B /,/, For Cautions for Use, see Relay Technical Information (Page 48 to 76). 9/1/2000 All Rights Reserved, © Copyright Matsushita Electric Works, Ltd. Go To Online Catalog