AFM8 AMPHENOL | Alldatasheet
Document overview
- Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
- PDF pages: 2
Technical content
MINIATURE ADJUSTABLE HAND BS owe PATION THIS HAND TOOL MUST NOT BE USED IN ANY POWERED | SEE REVERSE SIDE FOR IMPORTANT INFORMATION CONCERNING "PRESS” AS DEFINED BY OSHA CFR 1910.21! (46) LIMITED WARRANTY, AND LIMITATION OF LIABILITY. HOW TO USE DANIELS AFM8 (M22520/2-01) BASIC HAND CRIMP TOOL AND RELATED POSITIONERS TOOL IN OPEN POSITION _. GENERAL INFORMATION Nee 1. Designation AFM8 (M22520/2-01) refers wee eee to basic hand tool without positioners. SAFETY CLIP a Wire crimp range 20 AWG to 32 AWG. SO OTe Foan mn cxosen Position 2. The tool has a double action ratchet. a Note that the tool cannot be opened a =< CoD without completing the cycle. LS A TOOL_PREPARATION ls SAO ERS 1. Tool must be in open position. Be Pay aNt 2. Remove safety clip from positioner guide. cada @'y) 3. Select Positioner for contact to be OR crimped. S 4. Insert Positioner into positioner guide POSITIONER GUIDE SELECTOR KNOB and turn 90 degrees until bayonet pins BLUE lock. S. Install safety clip into positioner guide (optional). BAYONET PINS 6. Wire size and corresponding selector [ number are shown on data plate. 7. With tool still in open position, raise and rotate selector knob until number indicated on data plate for wire size to be crimped fs In line with Sel. No. arrow. CRIMPING INSTRUCTIONS DATA PLATE POSITIONER °K” SERIES 1, Insert contact and prepared wire into indenter opening from side opposite the Positioner. 2. Squeeze handles together until ratchet B NO-Go releases. Handle will return to the open PART NO. DIA DIA No position. Remove crimped contact and 0390 «| ~—oaans [| SC wire. REMOVING POSITIONER: CAUTION! 1. Remove safety clip and reverse procedure TG | described in step four (4) above. DO NOT CRIMP GAGE! NGO" *NO-cO" GREEN "GO RED °NO-GO" SELECTOR A 4.0001 B +.0001 = = A B [ 2 [oreo 0210 | [3 | oso ozo | G125 [os | oz60 [0310 | [6 | 0300 [7] 0340 [0380 | [8 asso .0440 | DANIELS MANUFACTURING CORP., 526 THORPE ROAD, ORLANDO, FL 32824, USA, PHONE 407/855-6161 FAX 407/855-6884 9/99 REV. A 10F 2 AFM8-DS
/ANUE Cla eell ATION GAGING INSTRUCTIONS “"NO-GO" GAGING "GO" GAGING Operate toal to fully closed pasition. Maintain firm hand pressure on the tool handles, Insert “NO-GO" Pperate tool to fuly closed position. | Maintain frm gage end as shown. The "NO-GO° gage moy partially " p rs C ‘ freely bet goa enter the indenter opening, but must not pass end gs shown. Gage must pass freely between completely through the opening. GREEN RED INDEN TER INDENTER CARE OF TOOL There is virtually no maintenance required. However, it is a good practice to keep indenter tips free of residual color band deposits and other debris. A small wire brush may be used for this purpose. We strongly recommend that you: 1. DO NOT immerse tools in cleaning solution. 2. DO NOT spray oil into tool to lubricate. 3. DO NOT attempt to disassemble tool or make repairs. This is a precision crimp tool and should be handled as such. DMC offers complete refurbishing and recalibration services. DMC specially engineers and manufactures complete tool kits to satisfy individual customer requirements, such as total aircraft support, general shop maintenance or production, on board ship and vehicle service, etc. LIMITATION OF LIABILITY DANIELS MANUFACTURING CORPORATION IS NOT LIABLE FOR CONSEQUENTIAL OR SPECIAL DAMAGES OF ANY NATURE OR KIND RESULTING FROM THE USE, OR MISUSE, OF ANY OF ITS PRODUCTS. OWNERS AND. USERS OF DMC PRODUCTS ASSUME FULL RESPONSIBILITY FOR INSTRUCTING THEIR EMPLOYEES IN THE PROPER AND SAFE USE OF SUCH PRODUCTS. LIMITED_ WARRANTY OMG (Daniels Manufacturing Corporation) warrants each new product ‘sold by it to be free from defects in material and workmanship under normal use and service. DMC's obligation under this warranty Is limited to the free correction or, at DMC's option, the refund of the purchase price af any such product which proves defective in normal service within ninety (90) days after delivery to the first user, provided thot the product is retumed to DMC with oll transportation charges prepaid and which shall appear to DMC’s satisfaction, ‘ofter OMG's inspection, to have been defective in material or workmanship, ik being understood that DMC products are not consumer products. This warranty shall not cover cny damage to any product which, m1 tne opinion of DMC, was caused by normal wear, misuse, improper aperation, tampering, neglect or accident. This warranty is in lieu of all other warranties express or implied. No worronty, express or implied, is made or authorized to be mode ‘or aseumed with respect to products of Daniels Manufacturing Corporation other than those herein set forth. 20F 2