AFBR-5601Z BOARDCOM | Alldatasheet

Document overview

  • Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
  • PDF pages: 13

Technical content

Features

  • RoHS Compliance
  • Compliant with Gigabit Interface Converter specification Rev. 5.4 (1)
  • AFBR-5601Z is compliant with proposed specifications for IEEE 802.3z/D5.0 Gigabit Ethernet (1000 Base-SX)
  • AFCT-5611Z is compliant with the ANSI 100-SM-LC-L revision 2 10 km link specification
  • Performance: AFBR-5601Z: 500 m with 50/125 µm MMF 220 m with 62.5/125 µm MMF AFCT-5611Z: 550 m with 50/125 µm MMF 550 m with 62.5/125 µm MMF 10 km with 9/125 µm SMF
  • Horizontal or vertical installation
  • AEL Laser Class 1 eye safe per IEC 60825-1
  • AEL Laser Class I eye safe per US 21 CFR
  • Hot-pluggable

Related Products

  • 850 nm VCSEL, 1 x 9 and SFF transceivers for 1000 base SX applications (HFBR-53D5, HFBR-5912E)
  • 1300 nm, 1 x 9 Laser transceiver for 1000 base-LX applications (HFCT-53D5)
  • Physical layer ICs available for optical interface (HDMP-1636A/46A) AFBR-5601Z and AFCT-5611Z Gigabit Interface Converters (GBIC) for Gigabit Ethernet Data Sheet Patent - www.avagotech.com/patents

The AFBR-5601Z has been developed with 850 nm short wavelength VCSEL technology while the AFCT-5611Z is based on 1300 nm long wavelength Fabry Perot laser technology. The AFBR-5601Z complies with Annex G of the GBIC specification Revision 5.4. In the 1000 BASE-SX environ - ment the AFBR-5601Z achieves 220 m transmission distance with 62.5 µm and 500 m with 50 µm multimode fiber respectively. The AFCT-5611Z complies with Annex F of the GBIC specification Revision 5.4 and reaches 10 km with 9/125 µm single mode fiber. Both the AFBR-5601Z and the AFCT-5611Z are Class 1 Eye Safe laser devices. Serial Identification The AFBR-56xxZ and AFCT-5611Z family complies with Annex D (Module Definition 4) of the GBIC specifica - tion Revision 5.4, which defines the Serial Identification Protocol. Definition 4 specifies a serial definition protocol. For this definition, upon power up, MOD_DEF(1:2) (Pins 5 and 6 on the 20-pin connector) appear as NC. Pin 4 is TTL ground. When the host system detects this condition, it activates the public domain serial protocol. The protocol uses the 2-wire serial CMOS E 2PROM protocol of the AT- MEL AT24C01A or similar. The data transfer protocol and the details of the manda- tory and vendor specific data structures are defined in Annex D of the GBIC specification Revision 5.4. Regulatory Compliance See the Regulatory Compliance Table for the targeted typical and measured performance for these transceiv - ers. The overall equipment design will determine the level it is able to be certified to. These transceiver performance targets are offered as a figure of merit to assist the de - signer in considering their use in equipment designs. Note: AFBR-5601Z is non-compliant for Tx fault timing. Electrostatic Discharge (ESD) There are two design cases in which immunity to ESD damage is important. The first case is during handling of the transceiver prior to inserting it into the host system. It is important to use normal ESD handling precautions for ESD sensitive devices. These precautions include using grounded wrist straps, work benches, and floor mats in ESD controlled areas. The second case to consider is static discharges during insertion of the GBIC into the host system. There are two guide tabs integrated into the 20-pin connector on the GBIC. These guide tabs are connected to circuit ground. When the GBIC is inserted into the host system, these tabs will engage before any of the connector pins. The mating connector in the host system must have its tabs connected to circuit ground. This discharges any stray static charges and establishes a reference for the power supplies that are sequenced later. Electromagnetic Interference (EMI) Most equipment designs utilizing these high-speed trans- ceivers from Avago Technologies will be required to meet the requirements of FCC in the United States, CENELEC EN55022 (CISPR 22) in Europe and VCCI in Japan. Immunity Equipment utilizing these transceivers will be subject to radio-frequency electromagnetic fields in some environ- ments. These transceivers have good immunity to such fields due to their shielded design. Eye Safety Laser-based GBIC transceivers provide Class 1 (IEC 60825- 1) and Class I (US 21 CFR[J]) laser eye safety by design. Avago Technologies has tested the current transceiver design for compliance with the requirements listed below under normal operating conditions and for compliance under single fault conditions. Outline Drawing An outline drawing is shown in Figure 1. More detailed drawings are shown in Gigabit Interface Converter speci- fication Rev. 5.4.

Notes: Blanks in ASCII column are numeric values not ASCII characters. 1. Address 63 and 95 are check sums. Address 63 is the check sum for bytes 0-62 and address 95 is the check sum for bytes 64-94. Addr Hex ASCII Addr Hex ASCII Addr Hex ASCII Addr Hex ASCII 0 1 40 41 A 68 39 9 96 20 1 7 41 46 F 69 38 8 97 20 2 1 42 42 B 70 30 0 98 20 3 0 43 52 R 71 36 6 99 20 4 0 44 2D - 72 32 2 100 20 5 0 45 35 5 73 33 3 101 20 6 1 46 36 6 74 30 0 102 20 7 0 47 30 0 75 33 3 103 20 8 0 48 31 1 76 32 2 104 20 9 0 49 5A Z 77 38 8 105 20 10 0 50 20 78 33 3 106 20 11 1 51 20 79 34 4 107 20 12 0D 52 20 80 33 3 108 20 13 0 53 20 81 37 7 109 20 14 0 54 20 82 33 3 110 20 15 0 55 20 83 30 0 111 20 16 32 56 30 0 84 39 9 112 20 17 16 57 30 0 85 38 8 113 20 18 0 58 30 0 86 30 0 114 20 19 0 59 30 0 87 36 6 115 20 20 41 A 60 03 88 32 2 116 20 21 56 V 61 52 89 33 3 117 20 22 41 A 62 0 90 30 0 118 20 23 47 G 63 Note 1 91 30 0 119 20 24 4F O 64 0 92 0 120 20 25 20 65 1A 93 0 121 20 26 20 66 0 94 0 122 20 27 20 67 0 95 Note1 123 20 28 20 124 20 29 20 125 20 30 20 126 20 31 20 127 20 32 20 33 20 34 20 35 20 36 0 37 00 38 17 39 6A GBIC Serial ID Memory Contents - AFBR-5601Z

Note: Blanks in ASCII column are numeric values not ASCII characters. 1 Address 63 and 95 are check sums. Address 63 is the check sum for bytes 0-62 and address 95 is the check sum for bytes 64-94. Addr Hex ASCII Addr Hex ASCII Addr Hex ASCII Addr Hex ASCII 0 1 40 41 A 68 39 9 96 20 1 6 41 46 F 69 38 8 97 20 2 1 42 43 C 70 30 0 98 20 3 0 43 54 T 71 36 6 99 20 4 0 44 2D - 72 32 2 100 20 5 0 45 35 5 73 33 3 101 20 6 2 46 36 6 74 30 0 102 20 7 0 47 31 1 75 33 3 103 20 8 0 48 31 1 76 34 4 104 20 9 0 49 5A Z 77 32 2 105 20 10 0 50 20 78 30 0 106 20 11 1 51 20 79 39 9 107 20 12 0D 52 20 80 34 4 108 20 13 0 53 20 81 32 2 109 20 14 0 54 20 82 39 9 110 20 15 64 55 20 83 30 0 111 20 16 37 56 30 0 84 39 9 112 20 17 37 57 30 0 85 38 8 113 20 18 0 58 30 0 86 30 0 114 20 19 0 59 30 0 87 36 6 115 20 20 41 A 60 05 88 32 2 116 20 21 56 V 61 1E 89 33 3 117 20 22 41 A 62 0 90 30 0 118 20 23 47 G 63 Note 1 91 30 0 119 20 24 4F O 64 0 92 0 120 20 25 20 65 1A 93 0 121 20 26 20 66 0 94 0 122 20 27 20 67 0 95 Note 1 123 20 28 20 124 20 29 20 125 20 30 20 126 20 31 20 127 20 32 20 33 20 34 20 35 20 36 0 37 00 38 17 39 6A GBIC Serial ID Memory Contents - AFCT-5611Z

Figure 1. Outline Drawing of AFBR-5601Z and AFCT-5611Z.

The worst-case Optical Power Budget (OPB) in dB for a fiber optic link is determined by the difference between the minimum transmitter output optical power (dBm avg) and the lowest receiver sensitivity (dBm avg). This OPB provides the necessary optical signal range to establish a working fiber-optic link. The OPB is allocated for the fiber-optic cable length and the corre sponding link penalties. For proper link perform ance, all penalties that affect the link performance must be acc ounted for within the link optical power bud- get. The Gigabit/sec Ethernet (GbE) IEEE 802.3z standard identifies, and has modeled, the contributions of these OPB penalties to establish the link length requirements for 62.5/125 µm and 50/125 µm multi mode fiber usage. In addi- tion, single-mode fiber with standard 1300 nm Fabry Perot lasers have been modeled and specified. Refer to IEEE 802.3z standard and its supplemental documents that develop the model, empirical results and final specifications. 10 km Link Support As well as complying with the LX 5 km standard, the AFCT- 56xxZ specification provides additional margin allowing for a 10 km Gigabit Ethernet link on single mode fiber. This is accomplished by limiting the spectral width and center wavelength range of the transmitter while increas- ing the output optical power and improving sensitivity. All other LX cable plant recommendations should be followed. CAUTION: There are no user serviceable parts nor any maintenance required for the AFBR-56xxZ and AFCT-56xxZ product family. All adjustments are made at the factory before shipment to our customers. Tampering with or modify - ing the performance of any Avago Technologies GBIC unit will result in voided product warranty. It may also result in improper operation of the circuitry, and possible overstress of the semiconductor components. Device degradation or product failure may result. Connection of either the AFBR-5601Z or the AFCT-5611Z to a non-approved optical source, operating above the recommended absolute maximum conditions, or op - erating in a manner inconsistent with unit design and function, may result in hazardous radiation exposure and may be considered an act of modifying or manufacturing a laser product. The person(s) performing such an act is required by law to recertify the laser product under the provisions of US 21 CFR (Subchapter J). Regulatory Compliance Feature Test Method Targeted Performance Electrostatic Discharge (ESD) to the Electrical Pins MIL-STD-883C Method 3015.7 Class 1 (>2000 V) Electrostatic Discharge (ESD) to the Duplex SC Receptacle Variation of IEC 61000-4-2 Typically withstand at least 15 kV without damage when port is contacted by a Human Body Model probe. Electromagnetic Interference (EMI) FCC Class B CENELEC EN55022 Class B (CISPR 22A) VCCI Class 1 Margins are dependent on customer board and chassis design. Immunity Variation of IEC 61000-4-3 Typically show no measurable effect from a10 V/m field swept from 27 to 1000 MHz applied to the transceiver without a chassis enclosure Laser Eye Safety US 21 CFR, Subchapter J perparagraphs 1002.10 and 1002.12 EN 60825-1: 1994+A11 EN 60825-2: 1994+A1 EN 60950: 1992+A1+A2+A3+A4+A11 AEL Class I, FDA/CDRH AFBR-5601Z Accession No. 9720151-51 AFCT-5611Z Accession No. 9521220-120AEL Class 1, TUV Rheinland of North America AFBR-5601Z Certificate No. R72040311.004 AFCT-5611Z Certificate No. 933/21201880/04 Protection Class III Component Recognition Underwriters Laboratories and Canadian Standards Association Joint Component Recognition for Information Technology Equipment Including Electrical Business Equipment. UL File E173874 RoHS Compliance Compliant to EU Directive 2002/95/EC.

1 RX_LOS 2 11 RGND 1

2 RGND 2 12 -RX_DAT 1

3 RGND 2 13 +RX_DAT 1

4 MOD_DEF(0) 2 14 RGND 1

5 MOD_DEF(1) 2 15 VDDR 2

6 MOD_DEF(2) 2 16 VDDT 2

7 TX_DISABLE* 2 17 TGND 1

8 TGND 2 18 +TX_DAT 1

9 TGND 2 19 -TX_DAT 1

10 TX_FAULT 2 20 TGND 1

1 RX_LOS Output Receiver Loss of Signal, TTL High, open collector

2 RGND Receiver Ground

3 RGND Receiver Ground

4 MOD_DEF(0) Output TTL Low

5 MOD_DEF(1) Input SCL Serial Clock Signal

6 MOD_DEF(2) Input/Output SDA Serial Data Signal

7 TX_DISABLE Input Transmit Disable

8 TGND Transmitter Ground

9 TGND Transmitter Ground

10 TX_FAULT Output Transmit Fault

11 RGND Receiver Ground

14 RGND Receiver Ground

15 VDDR Input Receiver +5 V supply

16 VDDT Input Transmitter +5 V supply

17 TGND Transmitter Ground

20 TGND Transmitter Ground

4 TTL Low SCL SDA Serial module definition protocol

with circuit ground prior to Sequence 1 signals.

  • This pin is tied high via 10 K pull-up resistor.

Table 1. SCA-2 Host connector pin assignment Table 3. Module Definition Table 2. Signal Definition

Short Wavelength GBIC: AFBR-5601Z Transmitter Section The transmitter section consists of an 850 nm VCSEL in an optical subassembly (OSA), which mates to the fiber cable. The VCSEL OSA is driven by a custom, silicon bi - polar IC which converts differential logic signals into an analog Laser Diode drive current. Receiver Section The receiver includes a GaAs PIN photodiode mounted together with a custom, silicon bipolar transimpedance preamplifier IC, in an OSA. The OSA interfaces to a cus - tom silicon bipolar circuit that provides post-amplifica - tion and quantization. The post-amplifier includes a Signal Detect circuit that provides TTL compatible logic- low output in response to the detection of a usable input optical signal. Absolute Maximum Ratings Stresses in excess of the absolute maximum ratings can cause catastrophic damage to the device. Limits apply to each parameter in isolation, all other parameters having values within the recommended operating conditions. It should not be assumed that limiting values of more than one parameter can be applied to the product at the same time. Exposure to the absolute maximum ratings for extended periods can adversely affect device reliability. Parameter Symbol Min. Typ. Max. Unit Notes Storage Temperature TS -40 +85 °C Supply Voltage VDDT VDDR -0.5 6.0 V Data Input Voltage TX_DAT -0.5 VDDT V 1 TransmitterDifferential Input Voltage ±TX_DAT 2000 mV p-p Relative Humidity RH 5 95 % Parameter Symbol Min. Typ. Max. Unit Notes Ambient Operating Temperature TA 0 +60 °C Case Temperature TCASE +75 °C 2 Supply Voltage VDDT VDDR 4.75 5.0 5.25 V Supply Current ITX + IRX 200 300 mA 3 Parameter Symbol Min. Typ. Max. Unit Notes Surge Current ISURGE +30 mA 4 Power Dissipation PDISS 1.00 1.58 W 5 Notes: 1. Up to applied VDDT. 2. See Figure 1 for measurement point. 3. Maximum current is specified at VCC = maximum @ maximum operating temperature and end of life. 4. Hot plug above actual steady state current. 5. Total TX + RX. Eye Safety Design The laser driver is designed to be Class 1 eye safe (CDRH21 CFR(J), IEC 60825-1) under a single fault condi- tion. To be eye safe, only one of two results can occur in the event of a single fault. The transmitter must either maintain normal eye safe operation or the transmitter should be disabled. There are three key elements to the safety circuitry: a monitor diode, a window detector circuit, and direct control of the laser bias. The window detection circuit monitors the average optical power using the monitor diode. If a fault occurs such that the dc regulation circuit cannot maintain the preset bias conditions within ±20%, the transmitter will automatically be disabled. Once this has occurred, an electrical power reset will allow an at - tempted turn-on of the transmitter. TX_FAULT can also be cleared by cycling TX_DISABLE high for a time interval >10 µs. Transceiver Electrical Characteristics (TA = 0°C to +60°C, VCC = 4.75 V to 5.25 V) Recommended Operating Conditions

Parameter Symbol Min. Typ. Max. Unit Notes Output Optical Power 50/125 µm, NA = 0.20 fiber 62.5/125 µm, NA = 0.275 fiber PO PO -9.5 -9.5 dBmavg. dBmavg. Optical Extinction Ratio 9 dB Center Wavelength lC 830 850 860 nm Spectral Width - rms 0.85 nm rms Optical Rise/Fall Time tr/tf 0.26 ns 1, 4 and Figure 2 RIN12 -117 dB/Hz Total Contributed Jitter TJ 227 ps p-p Coupled Power Ratio CPR 9 dB Max. Pout TX_DISABLE Asserted POFF -35 dBm Parameter Symbol Min. Typ. Max. Unit Notes Input Optical Power PIN -17 -22 0 dBm avg. Operating Center Wavelength lC 770 860 nm Return Loss 12 dB Receiver Loss of Signal - TTL Low PRX_LOS D -23 -17 dBm avg. Receiver Loss of Signal - TTL High PRX_LOS A -31 -26 dBm avg. Stressed Receiver Sensitivity 62.5 µm fiber50 µm fiber -12.5 -13.5 dBm dBm Stressed Receiver Eye Opening @TP4 201 ps 3 Electrical 3 dB Upper Cutoff Frequency

1500 MHz

Transmitter Optical Characteristics (TA = 0°C to +60°C, VCC = 4.75 V to 5.25 V Receiver Optical Characteristics (TA = 0°C to +60°C, VCC = 4.75 V to 5.25 V) Notes: (continured on page 10) 1. Pull-up resistor on host VCC. 2. Rising edge of TX_DISABLE to fall of output signal below 10% of nominal. 3. Falling edge of TX_DISABLE to rise of output signal above 90% of nominal. 4. From power on or hot plug after VDDT >4.75 V or From negation of TX_DISABLE during reset of TX_FAULT. 5. From occurrence of fault (output safety violation or VDDT <4.5 V). 6. TX_DISABLE HIGH before TX_DISABLE set LOW. 7. 20 - 80% values.

Figure 2. Transmitter Optical Eye Diagram Mask

  1. Modulated with 27-1 PRBS pattern. Results are for a BER of IE-12.
  2. Tested in accordance with the conformance testing requirements of IEEE802.3z.
  3. Laser transmitter pulse response characteristics are specified by an eye diagram (Figure 2).

Long Wavelength GBIC: AFCT-5611Z Transmitter Section The transmitter section consists of a 1300 nm MQW Fabry Perot Laser in an optical subassembly (OSA), which mates to the fiber optic cable. The Laser OSA is driven by a cus- tom, silicon bipolar IC which converts differential PECL logic signals (ECL referenced to a +5 V supply) into an analog drive current to the laser. The laser driver IC incorporates temperature compensa- tion and feedback from the OSA to maintain constant output power and extinction ratio over the operating temperature range. Receiver Section The receiver includes a PIN photodiode mounted to - gether with a custom, silicon bipolar transimpedance preamplifier IC, in an OSA. The OSA interfaces to a custom silicon bipolar circuit that provides post-ampli - fication and quantization. The post-amplifier includes a Signal Detect circuit that provides TTL compatible logic- low output in response to the detection of a usable input optical signal. Absolute Maximum Ratings Stresses in excess of the absolute maximum ratings can cause catastrophic damage to the device. Limits apply to each parameter in isolation, all other parameters having values within the recommended operating conditions. It should not be assumed that limiting values of more than one parameter can be applied to the product at the same time. Exposure to the absolute maximum ratings for extended periods can adversely affect device reliability. Parameter Symbol Min. Typ. Max. Unit Notes Storage Temperature TS -40 +85 °C Supply Voltage VDDT VDDR -0.5 6.0 V Data Input Voltage TX_DAT -0.5 VDDT V TransmitterDifferential Input Voltage ±TX_DAT 2000 mV p-p Relative Humidity RH 5 95 % Parameter Symbol Min. Typ. Max. Unit Notes Ambient Operating Temperature TA 0 +60 °C Case Temperature TCASE +75 °C 1 Supply Voltage VDDT VDDR 4.75 5.0 5.25 V Supply Current ITX + IRX 200 300 mA 2 Eye Safety Design The laser driver is designed to be Class 1 eye safe (CDRH21 CFR(J), IEC 60825-1) under a single fault condi- tion. There are three key elements to the safety circuitry: a monitor diode, a window detector circuit, and direct control of the laser bias. The window detection circuit monitors the average optical power using the photo diode in the laser OSA. If a fault occurs such that the dc bias circuit cannot maintain the preset conditions within ±20%, TX_FAULT (Pin 10) will be asserted (high). Note: Under any single fault, the laser optical output power will remain within Class 1 eye safe limits. Recommended Operating Conditions

Parameter Symbol Min. Typ. Max. Unit Notes Transmitter Differential Input Voltage ±TX_DAT 650 2000 mV p-p Tranmit Fault Load TX_FAULTLoad 4.7 10 kW 1 Transmit Fault Output - Low TX_FAULTL 0.0 0.5 v Transmit Fault Output - High TX_FAULTH VCC-0.5 VCC+0.3 v TX_DISABLE Assert Time t_off 3 10 µsec 2 TX_DISABLE Negate Time t_on 0.5 1 msec 3 Time to initialize, includes reset of TX_FAULT t_init 30 300 msec 4 TX_FAULT from fault to assertion t_fault 20 100 µsec 5 TX_DISABLE time to start reset t_reset 10 µsec 6 Parameter Symbol Min. Typ. Max. Unit Notes Receiver Differential Output Voltage ±RX_DAT 370 2000 mV p-p Receiver Output Rise Time trRX_DAT 0.35 ns 7 Receiver Output Fall Time tfRX_DAT 0.35 ns 7 Receiver Loss of Light Load RX_LOSLoad 4.7 10 kW 1 Receiver Loss of Signal Output Voltage - Low RX_LOSL 0.0 0.5 V Receiver Loss of Signal Output Voltage - High RX_LOSH VCC-0.5 VCC+0.3 V Receiver Loss of Signal Assert Time (off to on) tA,RX_LOS 100 µs Receiver Loss of Signal Deassert Time (on to off ) tD,RX_LOS 100 µs Notes: 1. Pull-up resistor on host VCC. 2. Rising edge of TX_DISABLE to fall of output signal below 10% of nominal. 3. Falling edge of TX_DISABLE to rise of output signal above 90% of nominal. 4. From power on or hot plug after VDDT >4.75 V or From negation of TX_DISABLE during reset of TX_FAULT. 5. From occurrence of fault (output safety violation or VDDT <4.5 V). 6. TX_DISABLE HIGH before TX_DISABLE set LOW. 7. 20 - 80% values. Receiver Electrical Characteristics (TA = 0°C to +60°C, VCC = 4.75 V to 5.25 V) AFCT-5611Z Transmitter Electrical Characteristics (TA = 0°C to +60°C, VCC = 4.75 V to 5.25 V) Parameter Symbol Min. Typ. Max. Unit Notes Surge Current ISURGE +30 mA 3 Power Dissipation PDISS 1.00 1.58 W 4 Notes: 1. See Figure 1 for measurement point. 2. Maximum current is specified at VCC = maximum @ maximum operating temperature and end of life. 3. Hot plug above actual steady state current. 4. Total TX + RX. Transceiver Electrical Characteristics (TA = 0°C to +60°C, VCC = 4.75 V to 5.25 V)

Parameter Symbol Min. Typ. Max. Unit Notes Output Optical Power 9/125 µm SMF 62.5/125 µm MMF 50/125 µm MMF PO -9.5 -11.5 -11.5 -7 -3 dBm dBm dBm Optical Extinction Ratio 9 dB Center Wavelength lC 1285 1310 1343 nm Spectral Width - rms 2.8 nm rms Optical Rise/Fall Time tr/tf 0.26 ns 1, 4 and Figure 2 RIN12 -116 dB/Hz Total Contributed Jitter TJ 227 ps p-p Coupled Power Ratio CPR 9 dB Max. Pout TX_DISABLE Asserted POFF -35 dBm Parameter Symbol Min. Typ. Max. Unit Notes Input Optical Power PIN -20 -25 -3 dBm avg. 2 Operating Center Wavelength lC 1270 1355 nm Return Loss 12 dB Receiver Loss of Signal - TTL Low PRX_LOS D -28 -20 dBm avg. Receiver Loss of Signal - TTL High PRX_LOS A -31 dBm avg. Stressed Receiver Sensitivity -14.4 dBm 3 Stressed Receiver Eye Opening @TP4 201 ps 3 Electrical 3 dB Upper Cutoff Frequency Notes: 1. 20 - 80% values. 2. Modulated with 27-1 PRBS pattern. Results are for a BER of IE-12. 3. Tested in accordance with the conformance testing requirements of IEEE802.3z. 4. Laser transmitter pulse response characteristics are specified by an eye diagram (Figure 2). AFCT-5611Z Transmitter Optical Characteristics (TA = 0°C to +60°C, VCC = 4.75 V to 5.25 V) Receiver Optical Characteristics (TA = 0°C to +60°C, VCC = 4.75 V to 5.25 V) For product information and a complete list of distributors, please go to our web site: www.avagotech.com Avago, Avago Technologies, and the A logo are trademarks of Avago Technologies in the United States and other countries. Data subject to change. Copyright © 2005-2013 Avago Technologies. All rights reserved. Obsoletes 5989-3792EN AV02-0255EN - January 29, 2013