ADG601

ADG601/ADG602 (Rev.E)

Document overview

• Manufacturer or author: Analog Devices, Inc.
• PDF pages: 12

Technical content

2 Ω, CMOS, ±5 V/+5 V SPST Switches Rev. E DOCUMENT FEEDBACK TECHNICAL SUPPORT Information furnished by Analog Devices is believed to be accurate and reliable "as is". However, no responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other rights of third parties that may result from its use. Specifications subject to change without notice. No license is granted by implication or otherwise under any patent or patent rights of Analog Devices. Trademarks and registered trademarks are the property of their respective owners. All Analog Devices products contained herein are subject to release and availability.

FEATURES

►Low on resistance, 3.3 Ω maximum ►<0.8 Ω on-resistance flatness ►Dual ±2.7 V to ±5.5 V or single +2.7 V to +5.5 V supplies ►Rail-to-rail input signal range ►Tiny, 6-lead SOT-23; 8-lead MSOP; and 820 μm × 2255 μm die ►Low power consumption ►TTL-/CMOS-compatible inputs

APPLICATIONS

►Automatic test equipment ►Power routing ►Communication systems ►Data acquisition systems ►Sample-and-hold systems ►Avionics ►Relay replacement ►Battery-powered systems FUNCTIONAL BLOCK DIAGRAMS Figure 1. Table 1. Truth Table throw (SPST) switches with on resistance typically less than 3.3 Ω. and are available in much smaller package sizes. extending to the supply rails.

1. Low on resistance (2 Ω typical)
2. Tiny, 6-lead SOT-23; 8-lead MSOP; and 820 μm × 2255 μm die
3. Rail-to-rail input signal range

analog.com Rev. E | 2 of 12

REVISION HISTORY

4/2025—Rev. D to Rev. E Changes to On Resistance (RON) Parameter and On-Resistance Flatness (RFLAT (ON)) Parameter, Changes to On Resistance (RON) Parameter and On-Resistance Flatness (RFLAT (ON)) Parameter,

analog.com Rev. E | 3 of 12 DUAL SUPPLY VDD = 5 V ± 10%, VSS = –5 V ± 10%, GND = 0 V, unless otherwise noted. Table 2. Parameter B Version1 Unit Test Conditions/Comments+25°C −40°C to +85°C ANALOG SWITCH Analog Signal Range VSS to VDD V VDD = +4.5 V, VSS = –4.5 V On Resistance (RON) 2 Ω typ VS = ±4.5 V, IDS = −10 mA; see Figure 15 3.3 5.5 Ω max On-Resistance Flatness (RFLAT (ON)) 0.35 0.4 Ω typ VS = ±3.3 V, IDS = −10 mA 0.75 0.8 Ω max LEAKAGE CURRENTS VDD = +5.5 V, VSS = −5.5 V ±0.25 ±1 nA max ±0.25 ±1 nA max Channel On Leakage, ID, IS (On) ±0.01 nA typ VS = VD = +4.5 V or −4.5 V; see Figure 17 ±0.25 ±1 nA max DIGITAL INPUTS Input High Voltage, VINH 2.4 V min Input Low Voltage, VINL 0.8 V max Input Current, IINL or IINH 0.005 μA typ VIN = VINL or VINH ±0.1 μA max Digital Input Capacitance, CIN 2 pF typ DYNAMIC CHARACTERISTICS2 tON 80 ns typ RL = 300 Ω, CL = 35 pF 120 155 ns max VS = 3.3 V; see Figure 18 tOFF 45 ns typ RL = 300 Ω, CL = 35 pF 75 90 ns max VS = 3.3 V; see Figure 18 Charge Injection 250 pC typ VS = 0 V, RS = 0 Ω, CL = 1 nF; see Figure 19 Off Isolation −60 dB typ RL = 50 Ω, CL = 5 pF, f = 1 MHz; see Figure 20 Bandwidth −3 dB 180 MHz typ RL = 50 Ω, CL = 5 pF; see Figure 21 CS (Off) 50 pF typ f = 1 MHz CD (Off) 50 pF typ f = 1 MHz CD, CS (On) 145 pF typ f = 1 MHz POWER REQUIREMENTS VDD = +5.5 V, VSS = −5.5 V IDD 0.001 μA typ Digital inputs = 0 V or 5.5 V 1.0 μA max ISS 0.001 μA typ Digital inputs = 0 V or 5.5 V 1.0 μA max 1 Temperature range for B version is −40°C to +85°C. 2 Guaranteed by design, not subject to production test.

analog.com Rev. E | 4 of 12 SINGLE SUPPLY VDD = 5 V ± 10%, VSS = 0 V, GND = 0 V, unless otherwise noted. Table 3. Parameter B Version1 Unit Test Conditions/Comments+25°C −40°C to +85°C ANALOG SWITCH Analog Signal Range 0 V to VDD V VDD = 4.5 V On Resistance (RON) 3.5 Ω typ VS = 0 V to 4.5 V, IDS = −10 mA; see Figure 15 5.5 8 Ω max On-Resistance Flatness (RFLAT (ON)) 0.2 0.2 Ω typ VS = 1.5 V to 3.3 V, IDS = –10 mA 0.75 Ω max LEAKAGE CURRENTS VDD = 5.5 V Source Off Leakage, IS (Off) ±0.01 nA typ VS = 4.5 V/1 V, VD = 1 V/4.5 V; see Figure 16 ±0.25 ±1 nA max Drain Off Leakage, ID (Off) ±0.01 nA typ VS = 4.5 V/1 V, VD = 1 V/4.5 V; see Figure 16 ±0.25 ±1 nA max Channel On Leakage, ID, IS (On) ±0.01 nA typ VS = VD = 4.5 V or 1 V; see Figure 17 ±0.25 ±1 nA max DIGITAL INPUTS Input High Voltage, VINH 2.4 V min Input Low Voltage, VINL 0.8 V max Input Current, IINL or IINH 0.005 μA typ VIN = VINL or VINH ±0.1 μA max Digital Input Capacitance, CIN 2 pF typ DYNAMIC CHARACTERISTICS2 tON 110 ns typ RL = 300 Ω, CL = 35 pF 220 280 ns max VS = 3.3 V; see Figure 18 tOFF 50 ns typ RL = 300 Ω, CL = 35 pF 80 110 ns max VS = 3.3 V; see Figure 18 Charge Injection 20 pC typ VS = 0 V, RS = 0 Ω, CL = 1 nF; see Figure 19 Off Isolation −60 dB typ RL = 50 Ω, CL = 5 pF, f = 1 MHz; see Figure 20 Bandwidth –3 dB 180 MHz typ RL = 50 Ω, CL = 5 pF; see Figure 21 CS (Off) 50 pF typ f = 1 MHz CD (Off) 50 pF typ f = 1 MHz CD, CS (On) 145 pF typ f = 1 MHz POWER REQUIREMENTS VDD = 5.5 V IDD 0.001 μA typ Digital inputs = 0 V or 5.5 V 1.0 μA max 1 Temperature range for B version is −40°C to +85°C. 2 Guaranteed by design, not subject to production test.

analog.com Rev. E | 5 of 12 TA = 25°C, unless otherwise noted. Table 4. Parameter Rating VDD to VSS 13 V VDD to GND −0.3 V to +6.5 V VSS to GND +0.3 V to –6.5 V Analog Inputs1 VSS − 0.3 V to VDD + 0.3 V Digital Inputs1 −0.3 V to VDD + 0.3 V or 30 mA (whichever occurs first) Continuous Current, S or D 100 mA Peak Current, S or D (Pulsed at 1 ms, 10% Duty Cycle Max)200 mA Operating Temperature Range Industrial (B Version) −40°C to +85°C Storage Temperature Range −65°C to +150°C Junction Temperature 150°C Thermal Resistance MSOP θJA 206°C/W θJC 44°C/W SOT-23 θJA 229.6°C/W θJC 91.99°C/W Lead Temperature, Soldering (10 sec)300°C IR Reflow, Peak Temperature 260°C 1 Overvoltages at IN, S, or D are clamped by internal diodes. Current should be limited to the maximum ratings given. Stresses at or above those listed under Absolute Maximum Ratings may cause permanent damage to the product. This is a stress rating only; functional operation of the product at these or any other conditions above those indicated in the operational section of this specification is not implied. Operation beyond the maximum operat- ing conditions for extended periods may affect product reliability. Only one absolute maximum rating may be applied at a time. ESD CAUTION ESD (electrostatic discharge) sensitive device. Charged devi- ces and circuit boards can discharge without detection. Although this product features patented or proprietary protection circuitry, damage may occur on devices subjected to high energy ESD. Therefore, proper ESD precautions should be taken to avoid performance degradation or loss of functionality.

analog.com Rev. E | 9 of 12 VDD Most positive power supply potential. VSS Most negative power supply potential. IDD Positive supply current. ISS Negative supply current. GND Ground (0 V) reference. S Source terminal. Can be an input or an output. D Drain terminal. Can be an input or an output. IN Logic control input. VD, VS Analog voltage on Terminal D and Terminal S. RON Ohmic resistance between Terminal D and Terminal S. RFLAT (ON) Flatness is defined as the difference between the maximum and minimum values of on resistance as measured over the specified analog signal range. IS (Off) Source leakage current with the switch off. ID (Off) Drain leakage current with the switch off. ID, IS (On) Channel leakage current with the switch on. VINL Maximum input voltage for Logic 0. VINH Minimum input voltage for Logic 1. IINL, IINH Input current of the digital input. CS (Off) Off switch source capacitance. Measured with reference to ground. CD (Off) Off switch drain capacitance. Measured with reference to ground. CD, CS (On) On switch capacitance. Measured with reference to ground. CIN Digital input capacitance. tON Delay between applying the digital control input and the output switching on. tOFF Delay between applying the digital control input and the output switching off. Charge Injection A measure of the glitch impulse transferred from the digital input to the analog output during switching. Off Isolation A measure of unwanted signal coupling through an off switch. On Response Frequency response of the on switch. Insertion Loss Loss due to the on resistance of the switch.

©2001-2025 Analog Devices, Inc. All rights reserved. Trademarks and registered trademarks are the property of their respective owners. One Analog Way, Wilmington, MA 01887-2356, U.S.A. Rev. E | 12 of 12 Package Drawing (Option) Package Type Package Description RM-8 MSOP 8-Lead Mini Small Outline Package RJ-6 SOT-23 6-Lead Small Outline Transistor Package For the latest package outline information and land patterns (footprints), go to Package Index. ORDERING GUIDE Model1 Temperature Range Package Description Packing Quantity Package Option Marking Code2 ADG601BRTZ-REEL −40°C to +85°C 6-Lead SOT-23 Reel, 10000 RJ-6 STB# ADG601BRTZ-REEL7 −40°C to +85°C 6-Lead SOT-23 Reel, 3000 RJ-6 STB# ADG601BRMZ −40°C to +85°C 8-Lead MSOP Tube, 50 RM-8 S1G ADG601BRMZ-REEL7 −40°C to +85°C 8-Lead MSOP Reel, 1000 RM-8 S1G ADG601C-PT7 Die Tape, 3000 ADG602BRTZ-REEL7 −40°C to +85°C 6-Lead SOT-23 Reel, 3000 RJ-6 S18 ADG602BRMZ −40°C to +85°C 8-Lead MSOP Tube, 50 RM-8 S18 ADG602BRMZ-REEL7 −40°C to +85°C 8-Lead MSOP Reel, 1000 RM-8 S18 1 Z = RoHS Compliant Part, # denotes RoHS compliant product, may be top or bottom marked. 2 Marking code on SOT-23 and MSOP is limited to three characters due to space constraints.