AD6C741 SSOUSA | Alldatasheet

Document overview

  • Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
  • PDF pages: 5

Technical content

1 Form A

The AD6C741 is a bi-directional, single-pole, single-throw, normally open high-load current relay. The relay consists of a Infrared LED optically coupled to a Photo Diode Array that drives two extremely low on-resistance, rugged drain-to-drain enhancement type DMOS transistors. Total device output resistance is guaranteed to be less than 0.25 ohms, making this device the ideal choice where high load current and minimal signal attenuation is required.

DESCRIPTION

ORDERING INFO/SUFFIXES* ABSOLUTE MAXIMUM RATINGS* APPROVALS Low on-resistance (0.17 ohms TYP)• High load current rating (1.8A MAX continuous load current)• Low input power consumption• High input-output isolation voltage• RoHS / Lead-Free / REACH Compliant• Security Systems• Multiplexers• Battery Monitoring• Meter Reading Systems• Data Acquisition• Medical Equipment• SMD/Surface Mount Leadform Option (50 pcs / tube)AD6C741-S: SMD/Tape & Reel packing option (1000 pcs / reel)AD6C741-STR: NOTE: Suffixes listed above are not included in marking on device for part number identification but must be included when ordering. PARAMETER UNIT MIN TYP MAX Storage Temperature °C -55 125 Operating Temperature °C -40 85 Continuous Input Current mA 50 Transient Input Current mA 400 Reverse Input Control Voltage V 6 Output Power Dissipation mW 800 Solder Temperature - Wave (10s) ºC 260 Solder Temperature - IR Reflow (10s) ºC 260 *The values indicated are absolute stress ratings. Functional operation of the device is not implied at these or any conditions in excess of those defined in electrical characteristics section of this document. Exposure to Absolute Ratings may cause permanent damage to the device and may adversely affect reliability. UL/ C-UL Recognized Component: File # E201932• EN/IEC 60950-01 Compliant• Page 1 of 5 AD6C741 rev 1.41 (9/17/2010) © 2010 Solid State Optronics • San José, CA AD6C741: DIP/Thru Hole (50 pcs / tube) SCHEMATIC DIAGRAM

ELECTRICAL CHARACTERISTICS - 25°C PARAMETER UNIT MIN TYP MAX TEST CONDITIONS INPUT SPECIFICATIONS LED Forward Voltage V 1.2 1.5 If = 5mA LED Reverse Voltage V 61 2 Ir = 10uA Turn-On Current m 2.5 5 Io = 1.5AA Turn-Off Current m 1A OUTPUT SPECIFICATIONS Blocking Voltage V 60 Io = 1uA Continuous Load Current m 1.8 If = 10mAA On-Resistance Ω 0.17 0.25 Io = 1A Leakage Current µ 0.2 1 Vo = 60VA Output Capacitance p 130 Vo = 25V, f = 1.0MHzF Offset Voltage m 0.2 If = 5mAV COUPLED SPECIFICATIONS Isolation Voltage V 3750 T = 1 minute Turn-On Time m 0.95 2.5 If = 10mA, Io = 1As Turn-Off Time m 0.03 0.25 If = 0mA, Io = 1As Isolation Resistance G 100Ω Coupled Capacitance p 3F Contact Transient Ratio V 2000 7000 dV = 50V/µ s Page 2 of 5 AD6C741 rev 1.41 (9/17/2010) © 2010 Solid State Optronics • San José, CA

Turn-Off Time (ms) Device Cou AD6C741 Typical Turn-Off Time Distribution N = 100, Ambient Temperature = 25°C On-Resistance (ohms) Device Cou AD6C741 100 Leakage Current (uA) Device Cou Typical On-Resistance Distribution N = 100, Ambient Temperature = 25°C AD6C741 Typical Leakage Current Distribution N = 100, Ambient Temperature = 25°C 69 70 71 72 73 74 75 76 Blocking Voltage (V) Device Cou AD6C741 500 1000 1500 2000 -40 -20 0 20 40 60 80 Temperature (C) Load Current (m Typical Blocking Voltage Distribution N = 100, Ambient Temperature = 25°C AD6C741 Maximum Load Current vs. Temperature Turn-On Time (ms) Device Cou AD6C741 Typical Turn-On Time Distribution N = 100, Ambient Temperature = 25°C Page 3 of 5 AD6C741 rev 1.41 (9/17/2010) © 2010 Solid State Optronics • San José, CA

6 PIN DUAL IN-LINE PACKAGE 6 PIN SURFACE MOUNT DEVICE

rev 1.41 (9/17/2010) © 2010 Solid State Optronics • San José, CA

Solid State Optronics (SSO) makes no warranties or representations with regards to the completeness and accuracy of this docume nt. SSO reserves the right to make changes to product description, specifications at any time without further notice. SSO shall not assume any liability arising out of the appl ication or use of any product or circuit described herein. Neither ci rcuit patent licenses nor indemnity are expressed or implied. Except as specified in SSO's Standard Terms & Conditions, SSO disclaims liability for consequential or other damage, and we mak e no other warranty, expressed or implied, including merchantability and fitness for particular use. DISCLAIMER LIFE SUPPORT POLICY SSO does not authorize use of its devices in life support applications wherein failure or malfunction of a device may lead to personal injury or death. Users of SSO devices in life support applications assume all risks of such use and agree to indemnify SSO against any an d all damages resulting from such use. Life support devices are defined as devices or systems which, (a) are intended for surgical im plant into the body, or (b) support or sustain life, and (c ) whose failure to perform when used properly in accordance with instructions for use can be reasonably expected to result in significant injury to the user, or (d) a critical component in any component of a life support device or system whose failure can be reasonably expected to caus e failure of the life support device or system, or to affect its safety or effe ctiveness. Page 5 of 5 AD6C741 rev 1.41 (9/17/2010) © 2010 Solid State Optronics • San José, CA