AD6C101_15 SSOUSA | Alldatasheet

Document overview

  • Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
  • PDF pages: 5

Technical content

1 Form A

The AD6C101 is a bi-directional, single-pole, single-throw, normally open multipurpose solid-state relay. With a high blocking voltage (600V), it is designed to replace electromechanical relays in high voltage switching applications. The relay consists of an integrated circuit that drives two rugged source-to-source enhancement type DMOS transistors - optically coupled to a light emitting diode. The output MOS transistors are protected with free-wheeling diodes that can handle up to 1.5A of inrush current, making the relay ideal for switching lamps and highly inductive loads.

DESCRIPTION

OPTIONS/SUFFIXES* SCHEMATIC DIAGRAM ABSOLUTE MAXIMUM RATINGS* APPROVALS High Blocking Voltage (600V)• High Input-Output Isolation (3750Vrms MIN)• 120mA MAX Continuous Load Current• On Resistance 40 ohms MAX• Long Life/High Reliability• Reed relay replacement• Meter reading systems• Medical equipment• Battery Monitoring• Multiplexers• Surface Mount Leadform Option (50 pcs / tub• -S Tape and Reel Option (1,000 pcs / reel)• -TR NOTE: Suffixes listed above are not included in marking on device for part number identification. PARAMETER UNIT MIN TYP MAX Storage Temperature °C -55 125 Operating Temperature °C -40 85 Continuous Input Current mA 50 Transient Input Current mA 400 Reverse Input Control Voltage V 6 Output Power Dissipation mW 800 Solder Temperature - Wave (10s) ºC 260 Solder Temperature - IR Reflow (10s) ºC 260 *The values indicated are absolute stress ratings. Functional operation of the device is not implied at these or any conditions in excess of those defined in electrical characteristics section of this document. Exposure to Absolute Ratings may cause permanent damage to the device and may adversely affect reliability. UL / C-UL Approved, File E201932• Page 1 of 5 AD6C101 rev 1.41 (3/24/2009) © 2009 Solid State Optronics • San José, CA

ELECTRICAL CHARACTERISTICS - 25°C PARAMETER UNIT MIN TYP MAX TEST CONDITIONS INPUT SPECIFICATIONS LED Forward Voltage V 1.8 2 If = 10mA LED Reverse Voltage V 0.5 Ir = 10uA Turn-On Current m 1.75 5 Io = 120mAA Turn-Off Current m 0.2A OUTPUT SPECIFICATIONS Blocking Voltage V 600 Io = 1uA Continuous Load Current m 120 If = 5mAA On-Resistance Ω 30 40 Io = 120mA Leakage Current µ 0.5 2 Vo = 600VA Output Capacitance p 6 If = 0, f = 1.0MHzF Offset Voltage m 0.2 If = 5mAV COUPLED SPECIFICATIONS Isolation Voltage V 3750 T = 1 minute Turn-On Time m 1 5 If = 5mA, Io = 120mAs Turn-Off Time m 0.5 2 If = 0mA, Io = 120mAs Isolation Resistance G 100Ω Coupled Capacitance p 3F Contact Transient Ratio V 2000 7000 dV = 50V/ µ s Page 2 of 5 AD6C101 rev 1.41 (3/24/2009) © 2009 Solid State Optronics • San José, CA

Turn-Off Time (ms) Device Count AD6C101 Typical Turn-Off Time Distribution N = 100, Ambient Temperature = 25°C 28 29 30 31 32 33 34 35 On-Resistance (ohms) Device Count AD6C101 Leakage Current (uA) Device Count Typical On-Resistance Distribution N = 100, Ambient Temperature = 25°C AD6C101 Typical Leakage Current Distribution N = 100, Ambient Temperature = 25°C 610 620 630 640 650 660 670 680 Blocking Voltage (V) Device Count AD6C101 100 150 -40 -20 0 20 40 60 80 Temperature (C) Load Current (mA) Typical Blocking Voltage Distribution N = 100, Ambient Temperature = 25°C AD6C101 Maximum Load Current vs. Temperature Turn-On Time (ms) Device Count AD6C101 Typical Turn-On Time Distribution N = 100, Ambient Temperature = 25°C Page 3 of 5 AD6C101 rev 1.41 (3/24/2009) © 2009 Solid State Optronics • San José, CA

6 PIN DUAL IN-LINE PACKAGE 6 PIN SURFACE MOUNT DEVICE

rev 1.41 (3/24/2009) © 2009 Solid State Optronics • San José, CA

Solid State Optronics (SSO) makes no warranties or representations wi th regards to the completeness and accuracy of this docume nt. SSO reserves the right to make changes to product description, specifications at any time without further notice. SSO shall not assume any liability arising out of the application or use of any product or circuit described herein. Neither ci rcuit patent licenses nor indemnity are expressed or implied. Except as specified in SSO's Standard Terms & Conditions, SSO disclaims liability for consequential or other damage, and we mak e no other warranty, expressed or implied, including merchantability and fitness for particular use. DISCLAIMER LIFE SUPPORT POLICY SSO does not authorize use of its devices in life support applications wherein failure or malfunction of a device may lead to p ersonal injury or death. Users of SSO devices in life suppor t applications assume all risks of such use and agree to indemnify SSO against any an d all damages resulting from such use. Life support devices are defined as devices or systems which, (a) are intended for surgical implant into the body, or (b) support or sustain life, and (c) whose failure to perf orm when used properly in accordance with instructions for u se can be reasonably expected to result in significant injury to the user, or (d) a crit ical component in any component of a life support device or system whose failure can be reasonably expected to c ause failure of the life support device or sys tem, or to affect its safety or effe ctiveness. Page 5 of 5 AD6C101 rev 1.41 (3/24/2009) © 2009 Solid State Optronics • San José, CA