AD2C101 SSOUSA | Alldatasheet

Document overview

  • Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
  • PDF pages: 5

Technical content

1 Form A

The AD2C101 is a bi-directional, single-pole, single-throw, normally open multipurpose solid-state relay. The relay consists of an IR LED optically coupled to a Photo Diode Array, which in turn drives two output MOSFETs. The AD2C101 provides high load voltage (600V) and high input-to-output isolation (5kV) in a miniature 4 pin DIP / SMD package, making it ideal for high-density board applications.

DESCRIPTION

OPTIONS/SUFFIXES* SCHEMATIC DIAGRAM ABSOLUTE MAXIMUM RATINGS* APPROVALS High Blocking Voltage (600V)• Small 4-pin DIP / SMD package• High input-to-output isolation (5000Vrms)• 100mA maximum continuous load current• 40 ohms maximum on-resistance• Long life/high reliability• Multiplexers• Meter reading systems• Data Acquisition• Medical equipment• Battery monitoring• Home/Safety security systems• Surface Mount Option (65 pcs / tube)• -S Tape and Reel Option (2000 pcs / reel)• -TR .04" (10.16mm) lead spacing (VDE0884)• -V NOTE: Suffixes listed above are not included in marking on device for part number identification. PARAMETER UNIT MIN TYP MAX Storage Temperature °C -40 150 Operating Temperature °C -40 85 Continuous Input Current mA 50 Transient Input Current (1us) mA 400 Reverse Input Control Voltage V 5 Output Power Dissipation mW 500 Solder Temperature - Wave (10s) 260 Solder Temperature - IR Reflow (10s) 260 *The values indicated are absolute stress ratings. Functional operation of the device is not implied at these or any conditions in excess of those defined in electrical characteristics section of this document. Exposure to Absolute Ratings may cause permanent damage to the device and may adversely affect reliability. Page 1 of 5 AD2C101 rev 1.42 (5/15/2008) © 2008 Solid State Optronics • San José, CA + INPUT - INPUT LOAD LOAD UL / C-UL Approved: File E201932

ELECTRICAL CHARACTERISTICS - 25°C PARAMETER UNIT MIN TYP MAX TEST CONDITIONS INPUT SPECIFICATIONS LED Forward Voltage V 1.8 2 If = 10mA Turn-On Current m 2.5 5 Io = 100mAA Turn-Off Current m 0.2A OUTPUT SPECIFICATIONS Blocking Voltage V 600 Io = 1uA Continuous Load Current m 100 If = 5mAA On-Resistance Ω 30 40 Io = 100mA Leakage Current µ 0.2 1 Vo = 600VA Output Capacitance p 6 If=0, f = 1.0MHzF Offset Voltage m 0.2 If = 5mAV COUPLED SPECIFICATIONS Isolation Voltage V 5000 T = 1 minuterm s Turn-On Time m 1 5 If = 5mA, Io = 100mA, Vo=20V, t=10mss Turn-Off Time m 0.05 3 If = 0mA, Io = 100mA, Vo=20V, t=10mss Isolation Resistance G 100Ω Coupled Capacitance p 3F Contact Transient Ratio V 2000 7000 dV = 50V/µ s Page 2 of 5 AD2C101 rev 1.42 (5/15/2008) © 2008 Solid State Optronics • San José, CA

Turn-Off Time (ms) Device Count AD2C101 Typical Turn-Off Time Distribution N = 100, Ambient Temperature = 25°C 27 28 29 30 31 32 33 34 On-Resistance (ohms) Device Count AD2C101 Leakage Current (uA) Device Count Typical On-Resistance Distribution N = 100, Ambient Temperature = 25°C AD2C101 Typical Leakage Current Distribution N = 100, Ambient Temperature = 25°C 600 610 620 630 640 650 660 670 Blocking Voltage (V) Device Count AD2C101 100 120 -40 -20 0 20 40 60 80 Temperature (C) Load Current (mA) Typical Blocking Voltage Distribution N = 100, Ambient Temperature = 25°C AD2C101 Maximum Load Current vs. Temperature Turn-On Time (ms) Device Count AD2C101 Typical Turn-On Time Distribution N = 100, Ambient Temperature = 25°C Page 3 of 5 AD2C101 rev 1.42 (5/15/2008) © 2008 Solid State Optronics • San José, CA

4 PIN DUAL IN-LINE PACKAGE 4 PIN SURFACE MOUNT DEVICE

rev 1.42 (5/15/2008) © 2008 Solid State Optronics • San José, CA

Solid State Optronics (SSO) makes no warranties or representations wi th regards to the completeness and accuracy of this docume nt. SSO reserves the right to make changes to product description, specifications at any time without further notice. SSO shall not assume any liability arising out of the application or use of any product or circuit described herein. Neither ci rcuit patent licenses nor indemnity are expressed or implied. Except as specified in SSO's Standard Terms & Conditions, SSO disclaims liability for consequential or other damage, and we mak e no other warranty, expressed or implied, including merchantability and fitness for particular use. DISCLAIMER LIFE SUPPORT POLICY SSO does not authorize use of its devices in life support applications wherein failure or malfunction of a device may lead to p ersonal injury or death. Users of SSO devices in life suppor t applications assume all risks of such use and agree to indemnify SSO against any an d all damages resulting from such use. Life support devices are defined as devices or systems which, (a) are intended for surgical implant into the body, or (b) support or sustain life, and (c) whose failure to perf orm when used properly in accordance with instructions for u se can be reasonably expected to result in significant injury to the user, or (d) a crit ical component in any component of a life support device or system whose failure can be reasonably expected to c ause failure of the life support device or sys tem, or to affect its safety or effe ctiveness. Page 5 of 5 AD2C101 rev 1.42 (5/15/2008) © 2008 Solid State Optronics • San José, CA