AD10XR104K500A RFE | Alldatasheet

Document overview

  • Manufacturer or author: Provided By alldatasheet.com(free datasheet download site)
  • PDF pages: 3

Technical content

Axial Leaded Multilayer Ceramic Capacitors are made with a superior epoxy coating for moisture and mechanical protection. The small size is suitable for a wide range of applications, including: data processing, telecommunications, instrumentation and industrial controls. INTRODUCTION FEATURES

  • Minature Size
  • Auto Insertable
  • Epoxy Coating CAPACITANCE CODE SIZE CODE & CAPACITANCE RANGE Page 1 of 3 MULTILAYER CERAMIC CAPACITOR AD Series (X7R/X5R/Y5V/Z5U): Axial Leaded RoHS Reliable• Code Capacitance 221 0.00022 F 102 222 0.01 103 F 473 0.047 F 104 0.1 F 105 1.0 F 106 10 F0.001 F 0.0022 µF PART NUMBER EXAMPLE AD10 XR 104 K 500 A Temperature Packing Code Voltage Code Tolerance Code Coefficient 2022.05.31 C1BD04 L D L (max)D (max) Size Code Dimensions (mm) 4.02.6 3.1 5.1 AD10 AD15 Voltage Vdc Voltage Code 6.3V 10V 16V 25V 50V 100V 250V 6.3V 10V 16V 25V 50V 100V 250V 500V 050 100 160 250 500 101 251 060 100 160 250 500 101 251 501 X7R X5R Y5V Z5U 0.22~2.20 0.10~1.50 0.00022~0.33 0.001~0.033 1.50~10.00 10.00~22.00 6.80~10.00 0.00022~0.10 0.30~4.70 0.68~2.20 0.47~1.00 0.033~0.47 0.015~0.15 0.001~0.033 0.33~4.70 1.00 0.22 10.00 3.30 4.70~22.00 2.20~10.00 1.00~4.70 0.47~2.20 47.00 22.00 10.00 4.70 2.20 TOLERANCE CODE Symbol Cap. Tolerance C ±0.25pF D ±0.5pF F ±1% G ±2% J ±5% K ±10% M ±20% Z +80%, -20% TEMPERATURE COEFFICIENT Code Temp. Charact. Temperature Range Capacitance Change CG C0G/NPO -55 ~ 125°C 0±30ppm/°C X5R X5R -55 ~ 85°C ±15°C XR X7R -55 ~ 125°C ±15°C * See other AD Series for X5R, X7R, Y5V, Z5U

MULTILAYER CERAMIC CAPACITOR AD Series (X7R/X5R/Y5V/Z5U): Axial Leaded RoHS 2022.05.31 C1BD04 DIMENSIONS

ELECTRICAL CHARACTERISTICS

ENVIRONMENTAL AND TEST CHARACTERISTICS Strength of termination Solderability of leads Measuring Condition Lead wire to be soldered vertically up to the coating end point. At least 75% of lead surface is covered SpecificationParameter Solder temperature: 260 ± 5°C Dipping: 2 ± 0.5 sec. (containing Ag 2~5%) (Flux shall be used) Force : 4 LB min. Keep time : 10±1 sec. Termination not to be broken or loosened Page 2 of 3 Withstanding Voltage Insulation Resistance Dissipation Factor (tanδ) Shall be measured at 25°C ± 2°C at the frequency and voltage X7R/X5R/Y5V @ 1Hz 1Hz ± 10%, 1±0.2Vrms Z5U No defects Apply rated voltage for 1 minute at 25°C ± 2°C and 70% R.H. max Applied voltage: Rated veltage X 2.5 100V~500V Rated voltage (over) X 1.5 Duration: 1 to 5 sec. The charge/discharge current is less than 50mA Parameter Measuring Condition More than 10GΩ or 500M whichever is less 16Vdc product : More than 10GΩ or 100M whichever is less Ω μF Ω μF 16Vdc product : Measurement voltage is 25Vdc X7R= 0.03max X7R= 0.055max.C ≥ 1.0uF) Y5V= 0.075max Z5U= 0.09max 25V min 16V X7R/X5R=0.05max. Y5V= 0.10max10V max X7R/X5R=0.05max. Y5V= 0.125max 6.3V X5R= 0.075max With the specified tolerance Specification Capacitance Tape Specification Symbol Dimension (mm) Pitch of component P 5.08±0.51 Culmulative Tolerance of P Over 6 Consecutive Units ±0.15 Tape Width Wt 6.0±1.0 Lead Wire Protrusion Le 1.0 max Lead Extension into Tape Li 1.5 max Offset Between Tapes ΔT 0.8 max Width Between Tapes Wt 52.4±1.5 Lead Diameter d 0.483 Centered C ±0.76 Deflection from Nominal Position Δh 1.2 max

for 48 4hrs, then measure. Apply the rated DC voltage at 40 ± 2°C and 90 to 95% R.H. for 500 hrs.+24 - 0 Initial measurement for perform a heat treatment at 150 °C for 1 for 48 4hrs.At room temperature. Perform the initial measurement. hours. Remove and let sit ± + 0 - 10 Perform the five cycles according to the four heat treatments listed in the following table. Remove and let sit at room temperaturefor 48 4hrs., then measure.± + 0 - 10 Initial measurement for perform a heat treatment at 150 °C for 1 for 48 4hrs. At room temperature. Perform the initial measurement. hours. Remove and let sit ± The lead wire is immersed in the melted solder 1.5mm to 2mm form the main body at 260 ± 5°C for 10 ± 0.5 sec Let sit at room temperature for 48 then measure. ± 4hrs. Initial measurement for perform a heat treatment at 150 for 1 for 48 4hrs.At room temperature. Perform the initial measurement. hours. Remove and let sit ± + 0 - 10 D.F. I.R. X7R/X5R= ±7.5% Y5V= ± 20% Z5U= ± 20% Item Measuring Condition Resistance to Soldering heat C Temperature Compensating Thermal shock Measuring Condition X7R= 0.03max X7R= 0.055max.(C≥1.0uF) Y5V= 0.075max Z5U= 0.09max 25V min 16V X7R/X5R=0.05max. Y5V= 0.10max 10V max X7R/X5R=0.05max. Y5V= 0.125max 6.3V X5R= 0.075max More than 10G or 500MΩ More than 10G or 100MΩ ‧ F, ‧ F, μ whichever is less. 16V dc product: μ whichever is less. Step Temp. (°C) Min. Operating Temp. Room Temp. Max. Operating Temp. Room Temp. Time 30±3 30±3 D.F. I.R. Item Measuring Condition C Temperature Compensating Measuring Condition 25V min 16V 10V max 6.3V Moisture resistance High temperature loading(Steady state) X7R/X5R= ±15% Y5V= ± 30% Z5U= ± 30% X7R/X5R=0.10max. Y5V= 0.15max X7R/X5R=0.10max. Y5V= 0.1875max X5R= 0.15max X7R= 0.06max X7R= 0.11max.(C≥1.0uF) Y5V= 0.1125max Z5U= 0.135max More than 1000G or 50M More than 1000G or 10M ‧ F, ‧ F, μ whichever is less. 16V dc product: μ whichever is less. Initial measurement for Apply 200% of the rated DC voltage for 1 hour at the maximum operating temperature Remove temperature for 48 4hrs. Perform the initial measurement. * 100% for 100V~500V ± 2°C. let sit at room Apply the 200% of rated DC voltage for 1000 hrs. ± 2°C. Remove and let sit at room at the maximum operating temperature temperaturefor 48 ± 4hrs., then measure. +48 - 0 The charge/discharge current is less than 50mA. MULTILAYER CERAMIC CAPACITOR AD Series (X7R/X5R/Y5V/Z5U): Axial Leaded RoHS 2022.05.31 C1BD04 Page 3 of 3 STORAGE 1. The storage conditions < 40°C, < 70% R.H. 2. After opening the package, please store in desiccators.