AD10CG104K500A RFE | Alldatasheet

Document overview

  • Manufacturer or author: Provided By alldatasheet.com(free datasheet download site)
  • PDF pages: 3

Technical content

Radial Leaded Multilayer Ceramic Capacitors are made with a superior epoxy coating for moisture and mechanical protection. The small size is suitable for a wide range of applications, including: data processing, telecommunications, instrumentation, and industrial controls. INTRODUCTION FEATURES

  • Epoxy Coating
  • Minature Size
  • Auto Insertable
  • Operating Temperature Range -55 to 125°C
  • Temperature Characterisistics 0 ± 30 PPM/°C PART NUMBER EXAMPLE Page 1 of 3 AD10 CG 104 K 500 A Temperature Packing Code Voltage Code Tolerance Code CAPACITANCE CODE Code Capacitance 1.0pF 1R0 3R3 3.3pF 100 10pF 470 47pF 101 100pF 102 1000pF 222 2200pF 103 10000pF 333 33000 pF SIZE CODE & CAPACITANCE RANGE Coefficient MULTILAYER CERAMIC CAPACITOR AD Series (C0G/NPO): Axial Leaded RoHS RFE International • Tel:(949) 833-1988 • Fax:(949) 833-1788 • E-Mail Sales@rfeinc.com C1BD03 2022.05.31 L D D (max) L (max) 50V 500 1 ~ 10,000 100V 101 1 ~ 4,700 250V 251 100 ~ 2,700 50V 500 3,900 ~ 33,000 100V 101 3,900 ~ 10,000 250V 251 3,300 ~ 8,200 500V 501 100 ~ 3,300 Dimensions (mm) C0G / NPO (pF)Voltage Vdc Voltage Code AD15 3.1 5.1 Size Code AD10 2.6 4.0 TOLERANCE CODE Symbol Cap. Tolerance C ±0.25pF D ±0.5pF F ±1% G ±2% J ±5% K ±10% M ±20% Z +80%, -20% TEMPERATURE COEFFICIENT Code Temp. Charact. Temperature Range Capacitance Change CG C0G/NPO -55 ~ 125°C 0±30ppm/°C X5R X5R -55 ~ 85°C ±15°C XR X7R -55 ~ 125°C ±15°C * See other AD Series for X5R, X7R, Y5V, Z5U

RFE International • Tel:(949) 833-1988 • Fax:(949) 833-1788 • E-Mail Sales@rfeinc.com MULTILAYER CERAMIC CAPACITOR AD Series (C0G/NPO): Axial Leaded RoHS C1BD03 2022.05.31

ELECTRICAL CHARACTERISTICS

Q Withstanding Voltage No defects Shall be measured at 25°C ± 2°C at the frequency and voltage Applied voltage: Rated voltage x 2.5 100V~500V Rated voltage (over) x 1.5 Duration: 1 to 5 sec. The charge/discharge current is less than 50mA Insulation Resistance More than 10GΩ or 500MΩ • µF Whichever is less 16Vdc product: More than 10GΩ or 100MΩ • µF whichever is less Capacitance With the specified tolerance SpecificationParameter Apply rated voltage for 1 minute at 25°C ± 2°C and 70% R.H. max 16Vdc product: Measurement voltage is 25Vdc >=C 30pF : Q 1000 C 30pF : Q 400+20xC (C is nominal capacitance) >=< <=C 1000pF@1MHz ± 20%, 1±0.2Vrms C 1000pF@1MHz ± 10%, 1±0.2Vrms> ENVIRONMENTAL AND TEST CHARACTERISTICS Strength of termination Solderability of leads Measuring Condition Lead wire to be soldered vertically up to the coating end point. At least 75% of lead surface is covered SpecificationParameter Solder temperature: 260 ± 5°C Dipping: 2 ± 0.5 sec. (containing Ag 2~5%) (Flux shall be used) Force : 4 LB min. Keep time : 10±1 sec. Termination not to be broken or loosened Tape Specification Symbol Dimension (mm) Pitch of component P 5.08±0.51 Culmulative Tolerance of P Over 6 Consecutive Units ±0.15 Tape Width Wt 6.0±1.0 Lead Wire Protrusion Le 1.0 max Lead Extension into Tape Li 1.5 max Offset Between Tapes ΔT 0.8 max Width Between Tapes Wt 52.4±1.5 Lead Diameter d 0.483 Centered C ±0.76 Deflection from Nominal Position Δh 1.2 max

RFE International • Tel:(949) 833-1988 • Fax:(949) 833-1788 • E-Mail Sales@rfeinc.com MULTILAYER CERAMIC CAPACITOR AD Series (C0G/NPO): Axial Leaded RoHS C1BD03 2022.05.31 Resistance to Soldering heat Let sit at room temperature for 24 ± 2hrs.then measure. Thermal shock Perform the initial measurement. the four heat treatments listed in the following table. Remove and let sit at room temperature for 24 2hrs., ± then measure. Step 1 2 3 4 Temp. (䂝ż Min. Operating Temp. Room Temp. Max. Operating Temp. Room Temp. Time 30Ò3 15 30Ò3 15 Perform the initial measurement. Measuring Condition High temperature loading Measuring Condition Measuring Condition Remove and let sit at room temperature for24 hrs., ± 2 then measure. Apply the rated DC voltage at 40 and 90 to 95% R.H. ± 2°C for 500 hrs.+24 - 0 Perform the initial measurement. Moisture resistance (Steady state) Perform the initial measurement. * 100% for 100V500V over. Apply 200%of the rated DC voltage for 1000 hrs at the maximum operating temperature 2°C. Remove and let sit at ± room temperature for 24 2hrs,± then measure. +48 - 0 The charge/discharge current is less than 50mA. Specification Perform the five cycles according to The lead wire is immersed in the melted solder 1.5mm to 2mm from the main body at 260 for 10 ± sec± 5°C 0.5

  • Withstanding voltage: No defects
  • Exterior: No abnormalities More than 10GΩ or 500MΩ • µF Whichever is less 16Vdc product: More than 10GΩ or 100MΩ • µF whichever is less More than 1000MΩ or 50MΩ • µF Whichever is less 16Vdc product: More than 1000MΩ or 10MΩ • µF whichever is less STORAGE 1. The storage conditions <40°C, <70% R.H. 2. After opening the package, please store in desiccators.