ACT-45B

DATASHEET SEARCH SITE | WWW.ALLDATASHEET.COM

Document overview

• Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
• PDF pages: 11

Technical content

For automobile signal line ACT series ACT45B [1812 inch]* (CAN-BUS) ACT45R [1812 inch] (FlexRay) ACT45L [1812 inch] (Ethernet) * Dimensions Code JIS[EIA] EMC Components

(2/11) 001-01 / 20131106 / e9711_act.fm EMC Components REMINDERS FOR USING THESE PRODUCTS Before using these products, be sure to request the delivery specifications. SAFETY REMINDERS Please pay sufficient attention to the warnings for safe designing when using these products. The storage period is less than 12 months. Be sure to follow the storage conditions (Temperature: 5 to 40°C, Humidity: 10 to 75% RH or less). If the storage period elapses, the soldering of the terminal electrodes may deteriorate. Do not use or store in locations where there are conditions such as gas corrosion (salt, acid, alkali, etc.). Before soldering, be sure to preheat components. The preheating temperature should be set so that the temperature difference between the solder temperature and chip temperature does not exceed 150°C. Soldering corrections after mounting should be within the range of the conditions determined in the specifications. If overheated, a short circuit, performance deterioration, or lifespan shortening may occur. When embedding a printed circuit board where a chip is mounted to a set, be sure that residual stress is not given to the chip due to the overall distortion of the printed circuit board and partial distortion such as at screw tightening portions. Self heating (temperature increase) occurs when the power is turned ON, so the tolerance should be sufficient for the set therm al design. Carefully lay out the coil for the circuit board design of the non-magnetic shield type. A malfunction may occur due to magnetic interference. Use a wrist band to discharge static electricity in your body through the grounding wire. Do not expose the products to magnets or magnetic fields. Do not use for a purpose outside of the contents regulated in the delivery specifications. The products listed on this catalog are intended for use in general electronic equipment (AV equipment, telecommunications equipment, home appliances, amusement equipment, computer equipment, personal equipment, office equipment, measurement equipment, industrial robots) under a normal operation and use condition. The products are not designed or warranted to meet the requirements of the applications listed below, whose performance and/or quality require a more stringent level of safety or reliability, or whose failure, malfunction or trouble could cause serious damage to society, person or property. If you intend to use the products in the applications listed below or if you have special requirements exceeding the range or conditions set forth in the each catalog, please contact us. (1) Aerospace/Aviation equipment (2) Transportation equipment (electric trains, ships, etc.) (3) Medical equipment (4) Power-generation control equipment (5) Atomic energy-related equipment (6) Seabed equipment (7) Transportation control equipment (8) Public information-processing equipment (9) Military equipment (10) Electric heating apparatus, burning equipment (11) Disaster prevention/crime prevention equipment (12) Safety equipment (13) Other applications that are not considered general-purpose

applications

When designing your equipment even for general-purpose applications, you are kindly requested to take into consideration securing protection circuit/device or providing backup circuits in your equipment. REMINDERS

(3/11) 001-01 / 20131106 / e9711_act.fm

• All specifications are subject to change without notice. EMC Components Common Mode Filters For automobile signal line

FEATURES

Compatible with an operating temperature range of –40 to +150°C, so can be used for vehicle devices requiring compatibility with high temperatures. (ACT45B, ACT45R) When mounting, the terminal and winding tape splicing part do not fuse. ACT45R for FlexRay, which uses our unique technology, is a product that can achieve DCR < 2/g58 @ 125 deg. C by reducing the DC resistance while maintaining a high L-value of 100μH. ACT45L for Ethernet, which uses our unique technology, is a product that can realize higher-level Scd21 mode conversion characteristics while maintaining a high L-value of 200μH. APPLICATION ACT45B CAN-BUS, FAXs, modems, ISDNs, etc. ACT45R FlexRay system. ACT45L Ethernet system. PART NUMBER CONSTRUCTION OPERATING TEMPERATURE RANGE, PACKAGE QUANTITY, PRODUCT WEIGHT /g13/g3The Storage temperature range is for after the circuit board is mounted. Overview of the ACT Series ACT45B - 510 - 2P - TL ˘˘˘ Series name Inductance(typ.) Number of lines Packaging style Internal code(μH) ACT45B 110 11 2P 2 lines TL ø330mm reel ACT45R 220 22 ACT45L 510 51 101 100 201 200 Type Temperature range Package quantity Individual weightOperating temperature Storage temperature/g13 ʢ°Cʣ ʢ°Cʣ ʢpieces/reelʣ ʢgʣ ACT45B –40 to +150 –40 to +150 2,500 0.14 ACT45R –40 to +150 –40 to +150 2,500 0.14 ACT45L –40 to +105 –40 to +105 2,500 0.2 Product compatible with RoHS directive Compatible with lead-free solders AEC-Q200 RoHS Directive Compliant Product: See the following for more details related to RoHS Directive compliant products. http://www.tdk.co.jp/rohs/

(4/11) 001-01 / 20131106 / e9711_act.fm

• All specifications are subject to change without notice. EMC Components Overview of the ACT Series RECOMMENDED REFLOW PROFILE Preheating Soldering Peak Temp. Time Temp. Time Temp. Time T1 T2 t1 T3 t2 T4 t3 150°C 180°C 60 to 120s 230°C 40s max. 245°C 5s Natural cooling Preheating Soldering T3 T3 t: Time Peak T: Temperature

(5/11) 001-01 / 20131106 / e9711_act.fm

• All specifications are subject to change without notice. EMC Components ACT series ACT45B Type SHAPE & DIMENSIONS RECOMMENDED LAND PATTERN CIRCUIT DIAGRAM 4.5±0.2 3.2±0.2 2.8±0.2 0.65±0.10.7±0.1 Marking Dimensions in mm 5.9 3.2 1.6 3.4 Dimensions in mm
• No polarity

(6/11) 001-01 / 20131106 / e9711_act.fm

• All specifications are subject to change without notice. EMC Components ACT seriesɹACT45B Type

ELECTRICAL CHARACTERISTICS

CHARACTERISTICS SPECIFICATION TABLE ˓Measurement equipment ˎ Equivalent measurement equipment may be used. IMPEDANCE VS. FREQUENCY CHARACTERISTICS ˓Measurement equipment ˎ Equivalent measurement equipment may be used. Common mode impedance (/g58) [10MHz] Common mode inductance(μH) +50/–30% [100kHz] Stray inductance (μH)typ. [100kHz] DC resistance (/g58)max. Rated current (A)max. Insulation resistance (M/g58)min. Rated voltage (V)max. Part No. min. typ. 300 600 11 0.05 0.6 0.25 10 50 ACT45B-110-2PTL˘˘˘ 500 1200 22 0.08 1.0 0.2 10 50 ACT45B-220-2PTL˘˘˘ 1000 2800 51 0.15 1.0 0.2 10 50 ACT45B-510-2PTL˘˘˘ 2000 5800 100 0.20 2.0 0.15 10 50 ACT45B-101-2PTL˘˘˘ Measurement item Product No. Manufacturer Common mode impedance 4991A Agilent Technologies Common mode inductance 4294A Agilent Technologies DC resistance 4338A Agilent Technologies Insulation resistance 4339A Agilent Technologies Product No. Manufacturer 4991A Agilent Technologies 1 10 100 1000 100000 10000 1000 100 Frequency (MHz) Impedance (Ω)

110 Common mode

101 Common mode

220 Common mode

510 Common mode

220 Differential mode

510 Differential mode

110 Differential mode

101 Differential mode

(7/11) 001-01 / 20131106 / e9711_act.fm

• All specifications are subject to change without notice. EMC Components ACT series ACT45R Type SHAPE & DIMENSIONS RECOMMENDED LAND PATTERN CIRCUIT DIAGRAM 4.5±0.2 3.2±0.2 2.8±0.2 0.65±0.10.7±0.1 Marking 5.9 3.2 1.6 3.4
• No polarity

(8/11) 001-01 / 20131106 / e9711_act.fm

• All specifications are subject to change without notice. EMC Components ACT seriesɹACT45R Type

CHARACTERISTICS SPECIFICATION TABLE ˓Measurement equipment ˎ Equivalent measurement equipment may be used. IMPEDANCE VS. FREQUENCY CHARACTERISTICS ˓Measurement equipment ˎ Equivalent measurement equipment may be used. Common mode impedance (/g58) [10MHz] Common mode inductance(μH) +50/–30% [100kHz] Stray inductance (μH)typ. [100kHz] DC resistance (/g58)max. Rated current (A)max. Insulation resistance (M/g58)min. Rated voltage (V)max. Part No. min. typ. 2200 5500 100 0.2 1.5 0.2 10 50 ACT45R-101-2P-TL001 Measurement item Product No. Manufacturer Common mode impedance 4991A Agilent Technologies Common mode inductance 4294A Agilent Technologies DC resistance 4338A Agilent Technologies Insulation resistance 4339A Agilent Technologies Product No. Manufacturer 4991A Agilent Technologies 1 10 100 1000 100000 10000 1000 100 Frequency (MHz) Impedance (Ω) 101 Common mode

(9/11) 001-01 / 20131106 / e9711_act.fm

• All specifications are subject to change without notice. EMC Components ACT series ACT45L Type SHAPE & DIMENSIONS RECOMMENDED LAND PATTERN CIRCUIT DIAGRAM 4.5±0.2 3.2±0.2 2.8±0.15 (0.65)(0.45) (1.4) Marking Dimensions in mm 5.5 3.9 0.7 2.1 Dimensions in mm
• No polarity

(10/11) 001-01 / 20131106 / e9711_act.fm

• All specifications are subject to change without notice. EMC Components ACT seriesɹACT45L Type

CHARACTERISTICS SPECIFICATION TABLE ˓Measurement equipment ˎ Equivalent measurement equipment may be used. IMPEDANCE VS. FREQUENCY CHARACTERISTICS ˓Measurement equipment ˎ Equivalent measurement equipment may be used. Common mode inductance (μH)typ. [100kHz] DC resistance (/g58)max. Rated current (mA)max. Insulation resistance (M/g58)min. Rated voltage (V)max. Part No. 200 4.5 100 10 50 ACT45L-201-2P-TL000 Measurement item Product No. Manufacturer Common mode inductance 4294A Agilent Technologies DC resistance 4338A Agilent Technologies Insulation resistance 4339A Agilent Technologies Product No. Manufacturer 4294A Agilent Technologies 1 10 100 1000 100000 10000 1000 100 Frequency (MHz) Impedance (Ω)

201 Common mode

201 Differential mode

(11/11) 001-01 / 20131106 / e9711_act.fm

• All specifications are subject to change without notice. EMC Components ACT series Packaging style REEL DIMENSIONS TAPE DIMENSIONS Type A W1 W2 N E ACT45B ø330±2 13.5±0.5 17.5±1 100±1 2 typ. ACT45R ø330±2 13.5±0.5 17.5±1 100±1 2 typ. ACT45L ø330±2 13.5±0.5 17.5±1 100±1 2 typ. Dimensions in mm Type A B øD0 E F P0 P1 P2 W K t ø13.0±0.2 ø21.0±0.8 N E2.0±0.5 A Dimensions in mm 1.0 B FE W P0P2 P1A øD0 t K Dimensions in mm Blank Products Blank 160min. 400 to 500 Drawing direction Start End