ACM2520-102-2P-T002

DATASHEET SEARCH SITE | WWW.ALLDATASHEET.COM

Document overview

• Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
• PDF pages: 9

Technical content

For high-speed differential signal line, general signal line EMC Components ACM2520 [1008 inch]* * Dimensions Code JIS[EIA] Common Mode Filters ACM2520 Type ACM Series

(2/9) 20151227 / cmf_commercial_signal_acm2520_en.fm EMC Components REMINDERS FOR USING THESE PRODUCTS Before using these products, be sure to request the delivery specifications. SAFETY REMINDERS Please pay sufficient attention to the warnings for safe designing when using these products. The storage period is less than 6 months. Be sure to follow the storage conditions (Temperature: 5 to 40°C, Humidity: 10 to 75% RH or less). If the storage period elapses, the soldering of the terminal electrodes may deteriorate. Do not use or store in locations where there are conditions such as gas corrosion (salt, acid, alkali, etc.). Before soldering, be sure to preheat components. The preheating temperature should be set so that the temperature difference between the solder temperature and chip temperature does not exceed 150°C. Soldering corrections after mounting should be within the range of the conditions determined in the specifications. If overheated, a short circuit, performance deterioration, or lifespan shortening may occur. When embedding a printed circuit board where a chip is mounted to a set, be sure that residual stress is not given to the chip due to the overall distortion of the printed circuit board and partial distortion such as at screw tightening portions. Self heating (temperature increase) occurs when the power is turned ON, so the tolerance should be sufficient for the set therm al design. Carefully lay out the coil for the circuit board design of the non-magnetic shield type. A malfunction may occur due to magnetic interference. Use a wrist band to discharge static electricity in your body through the grounding wire. Do not expose the products to magnets or magnetic fields. Do not use for a purpose outside of the contents regulated in the delivery specifications. The products listed on this catalog are intended for use in general electronic equipment (AV equipment, telecommunications equipment, home appliances, amusement equipment, computer equipment, personal equipment, office equipment, measurement equipment, industrial robots) under a normal operation and use condition. The products are not designed or warranted to meet the requirements of the applications listed below, whose performance and/or quality require a more stringent level of safety or reliability, or whose failure, malfunction or trouble could cause serious damage to society, person or property. If you intend to use the products in the applications listed below or if you have special requirements exceeding the range or conditions set forth in the each catalog, please contact us. (1) Aerospace/Aviation equipment (2) Transportation equipment (cars, electric trains, ships, etc.) (3) Medical equipment (4) Power-generation control equipment (5) Atomic energy-related equipment (6) Seabed equipment (7) Transportation control equipment (8) Public information-processing equipment (9) Military equipment (10) Electric heating apparatus, burning equipment (11) Disaster prevention/crime prevention equipment (12) Safety equipment (13) Other applications that are not considered general-purpose

applications

When designing your equipment even for general-purpose applications, you are kindly requested to take into consideration securing protection circuit/device or providing backup circuits in your equipment. REMINDERS

(3/9) 20151227 / cmf_commercial_signal_acm2520_en.fm Please be sure to request delivery specifications that provide further details on the features and specifications of the produc ts for proper and safe use. Please note that the contents may change without any prior notice due to reasons such as upgrading. EMC Components Common Mode Filters For high-speed differential signal line, general signal line

FEATURES

Downsized wound type chip common mode filter that maintains requi red common mode filter characteristics. Impedance for common mode noise can clear 1000/g58 [100MHz], and has excellent EMC suppression. Differential mode impedance is suppressed, so there is virtually no affect on high speed signals. There is a two-line type and a three-line type, so they can be used for various circuits and noise. APPLICATION Common mode noise countermeasure for high-speed differential signals where influence to the signal is a concern. USB line for PCs and peripheral devices. IEEE1394 lines and ETHERNET lines for PCs, STBs, etc. LCD panel LVDS and Panel Link lines. PART NUMBER CONSTRUCTION OPERATING TEMPERATURE RANGE, PACKAGE QUANTITY, PRODUCT WEIGHT /g13/g3The Storage temperature range is for after the circuit board is mounted. Overview of ACM2520 Type ACM 2520 - 301 - 2P - T 002 Series name L×W×H Dimensions Impedance Number of lines Packaging style Internal code(mm) (/g58) at 100MHz 2520 2.5×2.0×1.2 301 300 2P 2 lines T ø180mm reel 002 3P 3 lines Type Temperature range Reel diameter Package quantity Individual weight Operating temperature ʢ°Cʣ Storage temperature/g13 ʢ°Cʣ ʢmmʣ (pieces/reel) ʢmgʣ ACM2520 –40 to +85 –40 to +85 ø180 2,000 25 Product compatible with RoHS directive Compatible with lead-free solders RoHS Directive Compliant Product: See the following for more details related to RoHS Directive compliant products. http://product.tdk.com/en/environment/rohs/

(4/9) 20151227 / cmf_commercial_signal_acm2520_en.fm Please be sure to request delivery specifications that provide further details on the features and specifications of the produc ts for proper and safe use. Please note that the contents may change without any prior notice due to reasons such as upgrading. EMC Components ACM2520 Type RECOMMENDED REFLOW PROFILE Preheating Soldering Peak Temp. Time Temp. Time Temp. Time T1 T2 t1 T3 t2 T4 t3 150°C 180°C 60 to 120s 230°C 10 to 30s 245°C 5s Natural cooling Preheating Soldering T3 T3 t: Time Peak T: Temperature

(5/9) 20151227 / cmf_commercial_signal_acm2520_en.fm Please be sure to request delivery specifications that provide further details on the features and specifications of the produc ts for proper and safe use. Please note that the contents may change without any prior notice due to reasons such as upgrading. EMC Components ACM2520-2P Type SHAPE & DIMENSIONS RECOMMENDED LAND PATTERN CIRCUIT DIAGRAM 2.5±0.2 2.0±0.21.2±0.1 0.85 1.30 1.6 0.450.45 Dimensions in mm 1.5 0.80.8 0.40 1.3 Dimensions in mm

• No polarity

(6/9) 20151227 / cmf_commercial_signal_acm2520_en.fm Please be sure to request delivery specifications that provide further details on the features and specifications of the produc ts for proper and safe use. Please note that the contents may change without any prior notice due to reasons such as upgrading. EMC Components ACM2520-2P Type

ELECTRICAL CHARACTERISTICS

CHARACTERISTICS SPECIFICATION TABLE ˓Measurement equipment ˎ Equivalent measurement equipment may be used. IMPEDANCE VS. FREQUENCY CHARACTERISTICS ˓Measurement equipment ˎ Equivalent measurement equipment may be used. Impedance [100MHzʧ DC resistance [per line] Rated voltage Insulation resistance Rated current Part No. 225 300 0.35 20 10 0.4 ACM2520-301-2P-T002 330 450 0.4 20 10 0.35 ACM2520-451-2P-T002 450 600 0.45 20 10 0.3 ACM2520-601-2P-T002 750 1000 0.9 20 10 0.2 ACM2520-102-2P-T002 Measurement item Product No. Manufacturer Common mode impedance 4991A Keysight Technologies DC resistance 4338A Keysight Technologies Insulation resistance 4339A Keysight Technologies Product No. Manufacturer 4991A Keysight Technologies 1 10 100 1000 10000 1000 100 Frequency (MHz) Impedance (Ω)

601 Common mode

301 Common mode

451 Common mode

102 Common mode

451 Differential mode

601 Differential mode

301 Differential mode

102 Differential mode

(7/9) 20151227 / cmf_commercial_signal_acm2520_en.fm Please be sure to request delivery specifications that provide further details on the features and specifications of the produc ts for proper and safe use. Please note that the contents may change without any prior notice due to reasons such as upgrading. EMC Components ACM2520-3P Type SHAPE & DIMENSIONS RECOMMENDED LAND PATTERN CIRCUIT DIAGRAM 2.5±0.2 1.2±0.1 0.85 1.6 0.450.45 2.0±0.2 1.3=P0.65×2 Dimensions in mm 1.5 0.80.8 0.35 1.3=P0.65×2 Dimensions in mm 3 4

• No polarity

(8/9) 20151227 / cmf_commercial_signal_acm2520_en.fm Please be sure to request delivery specifications that provide further details on the features and specifications of the produc ts for proper and safe use. Please note that the contents may change without any prior notice due to reasons such as upgrading. EMC Components ACM2520-3P Type CHARACTERISTICS SPECIFICATION TABLE ˓Measurement equipment ˎ Equivalent measurement equipment may be used. IMPEDANCE VS. FREQUENCY CHARACTERISTICS ˓Measurement equipment ˎ Equivalent measurement equipment may be used. Impedance [100MHzʧ DC resistance [per line] Rated voltage Insulation resistance Rated current Part No. 600 800 1.6 20 10 0.15 ACM2520-801-3P-T002 Measurement item Product No. Manufacturer Common mode impedance 4991A Keysight Technologies DC resistance 4338A Keysight Technologies Insulation resistance 4339A Keysight Technologies Product No. Manufacturer 4991A Keysight Technologies 1 10 100 1000 10000 1000 100 Frequency (MHz) Impedance (Ω)

801 Common mode

801 Differential mode

(9/9) 20151227 / cmf_commercial_signal_acm2520_en.fm Please be sure to request delivery specifications that provide further details on the features and specifications of the produc ts for proper and safe use. Please note that the contents may change without any prior notice due to reasons such as upgrading. EMC Components ACM2520 Type PACKAGING STYLE REEL DIMENSIONS TAPE DIMENSIONS Type A W1 W2 N E ACM2520 ø180±3 9+1/–0 13±1 60+1–0 2 typ. Dimensions in mm Type A B øD0 E F P0 P1 P2 W K t ø13.0±0.2 ø21.0±0.8 N E2.0±0.5 A Dimensions in mm 1.0 W F E P2øD0 B A t K 160min. Taping 440min. Drawing direction 500 to 560min. Dimensions in mm