AAT3104 SKYWORKS | Alldatasheet

Document overview

  • Manufacturer or author: Provided By alldatasheet.com(free datasheet download site)
  • PDF pages: 15

Technical content

Features

  • Drives up to 4 LEDs at up to 3 1mA each
  • Automatic Switching Between 1x and 2x Modes
  • 1MHz Switching Frequency
  • Linear LED Output Current Control
  • Single-wire, S2Cwire Interface AAT3104-1: 16-step AAT3104-2: 32-step
  • ±10% LED Output Current Accuracy
  • ±3% LED Output Current Matching
  • Low-current Shutdown Mode
  • Built-in Thermal Protection
  • Automatic Soft-start
  • Available in 2x2mm SC70JW-10 Package

Applications

  • Cordless Phone Handsets
  • Digital Cameras
  • Mobile Phone Handsets
  • MP3 and PMP Players Typical Application Input Voltage 2.7V to 5.5V EN/SET S2Cwire Interface IN EN/SET OUT COUT 1µF GND AAT3104CP 1µF CIN 1µF

Low Cost 1x/2x Four-Channel Charge Pump WLED Driver Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com 202124A • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice. • July 2, 2012 Pin Descriptions Pin# Name Description 1 D2 LED2 Current Source Output. D2 is the output of LED2 current source. Connect LED2’s anode to D2 and its cathode to GND. 2 D1 LED1 Current Source Output. D1 is the output of LED1 current source. Connect LED1’s anode to D1 and its cathode to GND. 3 OUT Charge Pump Output. OUT is the output of the charge pump. Bypass OUT to GND with a 1μF or larger ceramic capacitor. 4 C- Charge Pump Capacitor Negative Node. 5 C+ Charge Pump Capacitor Positive Node. Connect a 1μF ceramic capacitor between C+ and C-. 6 GND Analog Ground. Connect this pin to the system’s analog ground plane. 7 EN/SET LED Enable and serial control input. EN/SET is the ON/OFF control for the LED and the S2Cwire digital input for the AAT3104-1/-2 to control serially the LED brightness according to the maximum current. 8 IN Power source input. Connect IN to the power source, typically the battery. Bypass IN to GND with a 1μF or larger ceramic capacitor. 9 D4 LED4 Current Source Output. D4 is the output of LED4 current source. Connect LED4’s anode to D4 and its cathode to GND. 10 D3 LED3 Current Source Output. D3 is the output of LED3 current source. Connect LED3’s anode to D3 and its cathode to GND. Pin Configuration SC70JW-10 (Top View) EN/SET GND D2 1 OUT IN

Low Cost 1x/2x Four-Channel Charge Pump WLED Driver Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com 202124A • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice. • July 2, 2012 Absolute Maximum Ratings1 Symbol Description Value Units VIN, VOUT, VC+, VC-, VD1...4 IN, C+, C-, OUT, D1, D2, D3, and D4 Pin Voltages to GND -0.3 to 6.0 V VEN/SET EN/SET Pin Voltage to GND -0.3 to VIN + 0.3 V TS Storage Temperature Range -65 to 150 °C TJ Operating Junction Temperature Range -40 to 150 °C TLEAD Maximum Soldering Temperature (at leads, 10 sec) 300 °C Thermal Information Symbol Description Value Units PD Maximum Power Dissipation2, 3 625 mW θJA Maximum Thermal Resistance3 160 °C/W 1. Stresses above those listed in Absolute Maximum Ratings may cause permanent damage to the device. Functional operation at conditions other than the operating conditions specified is not implied. Only one Absolute Maximum Rating should be applied at any one time. 2. Mounted on an FR4 circuit board. 3. Derate 6.25mW/°C above 40°C ambient temperature.

Low Cost 1x/2x Four-Channel Charge Pump WLED Driver Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com 202124A • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice. • July 2, 2012 Electrical Characteristics1 IN = EN = 3.6V, CIN = 1µF, COUT = 1µF, C1 = 1µF, TA = -40°C to 85°C unless otherwise noted. Typical values are at T A = 25°C. Symbol Description Conditions Min Typ Max Units Input Power Supply VIN Input Voltage Range 2.7 5.5 V Iq Quiescent Current IN = 5.5V, EN = IN, VD1 = VD2 = VD3 = 0V 6 mA IIN No Load Operating Current IN = 5.5V, EN = IN, ID1 = ID2 = ID3 = ID4 = FS, VD1 = VD2 = VD3 = VD4 = IN – 1.5V, Exclude IDN current, 1x mode 3.5 mA Operating, ID1 = ID2 = ID3 = ID4 = OPEN, 2x mode 6 mA IIN(SHDN) Input Shutdown Current EN/SET = GND 1 μA Charge Pump Section IOUT OUT Maximum Output Current 150 mA VOUT Charge Pump Output Voltage When charge pump is on 5 V fOSC Charge Pump Oscillator Frequency 0.6 0.8 1.05 MHz VIN_(TH) Charge Pump Mode Hysteresis ID1 = ID2 = ID3 = ID4 =30mA 150 250 mV tOUT LED Output Current Start-up Time EN/SET =IN 190 μs AAT3104-1/-2: LED Current Source Outputs ID_(MAX) D1 – D4 Current Accuracy (AAT3104-1 only) DATA = 1, VIN – VF = 1.5V 27 30 33 mA ID_(MAX) D1 – D4 Current Accuracy (AAT3104-2 only) DATA = 1, VIN – VF = 1.5V 28 31 34 mA ΔID_(MAX) D1 – D4 Current Matching DATA = 1, VIN – VF = 1.5V ±3 % ID_(DATA15) D1 – D4 Current Accuracy (AAT3104-1 only) DATA = 15, VIN – VF = 1.5V 1.6 2.0 2.4 mA ID_(DATA29) D1 – D4 Current Accuracy (AAT3104-2 only) DATA = 29, VIN – VF = 1.5V 1.6 2.0 2.4 mA VD_(TH) D1- D4 Charge Pump Mode Transition Threshold ID1 = ID2 = ID3 = ID4 = 30mA, VIN – VD1 is measured 380 mV ID1 = ID2 = ID3 = ID4 = 20mA, VIN – VD1 is measured 350 mV AAT3104-1/-2: EN/SET and S2Cwire Control VENH EN/SET Input High Threshold Voltage 1.4 V VENL EN/SET Input Low Threshold Voltage 0.4 V IEN(LKG) EN/SET Input Leakage Current EN/SET = IN = 5V -1 1 μA tEN/SET(OFF) EN/SET Input OFF Timeout 500 µs tEN/SET(LAT) EN/SET Input Latch Timeout 500 µs tEN/SET(LOW) EN/SET Input Low Time 0.3 75 µs tENSET(H-MIN) EN/SET Minimum High Time 50 ns tENSET(H-MAX) EN/SET Maximum High Time 75 µs 1. The AAT3104 is guaranteed to meet performance specification over the -40°C to 85°C operating temperature range and are assured by design, characterization and correlation with statistical process controls.

Low Cost 1x/2x Four-Channel Charge Pump WLED Driver Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com 202124A • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice. • July 2, 2012 Typical Characteristics VIN = 3.6V, CIN = COUT = C1 = 1μF; TA = 25°C, unless otherwise noted. 1X Mode Turn-On Waveform (VIN = 4.2V; Load = 120mA) Time (200µs/div) EN (1V/div) VLED (2V/div) IIN (200mA/div) VOUT (2V/div) 2X Mode Turn-On Waveform (VIN = 3.6V; Load = 120mA) Time (200µs/div) EN (1V/div) VLED (2V/div) IIN (250mA/div) VOUT (2V/div) 2X Mode Turn-Off Waveform (VIN = 3.6V; Load = 120mA) Time (200µs/div) EN (1V/div) VLED (2V/div) IIN (250mA/div) 2X Mode Output Ripple (VIN = 3.6V; Load = 120mA) Time (0.4µs/div) VOUT (AC Coupled) (20mV/div) VIN (AC Coupled) (5mV/div) 1mA to 30mA LED Current Step (VIN = 4.2V) Time (80µs/div) VLED 2V/div IIN 200mA/div VOUT 2V/div EN 1V/div 30mA to 1mA LED Current Step (VIN = 4.2V) Time (80µs/div) VLED (2V/div) IIN (200mA/div) VOUT (2V/div) EN (1V/div)

Low Cost 1x/2x Four-Channel Charge Pump WLED Driver Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com 202124A • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice. • July 2, 2012 Typical Characteristics VIN = 3.6V, CIN = COUT = C1 = 1μF; TA = 25°C, unless otherwise noted. Current Matching vs. Temperature (AAT3104-2; Code = 1) Temperature (°C) Current (mA) 29.0 29.5 30.0 30.5 31.0 31.5 32.0 32.5 33.0 -40- 15 10 35 60 85 Efficiency vs. Input Voltage (ILED = 31mAx4; Voltage Sweep Upwards) Input Voltage (V) Efficiency (%) VF = 2.7V VF = 3.0V VF = 3.3V VF = 3.6V Efficiency vs. Input Voltage (ILED = 31mAx4; Voltage Sweep Downwards) Input Voltage (V) Efficiency (%) VF = 2.7V VF = 3.0V VF = 3.3V VF = 3.6V Quiescent Current vs. Input Voltage Input Voltage (V) Quiescent Current (mA) 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 6.0 6.5 85°C 25°C -40°C Shutdown Current vs. Temperature Temperature (°C) ShutdownnCurrent (nA) -40- 15 10 35 60 85 VIN = 5.5V VIN = 2.7V Frequency vs. Temperature Temperature (°C) Frequency (KHz) -40- 15 10 35 60 85 750 760 770 780 790 800 810 820 830 840 850

Low Cost 1x/2x Four-Channel Charge Pump WLED Driver Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com 202124A • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice. • July 2, 2012 Typical Characteristics VIN = 3.6V, CIN = COUT = C1 = 1μF; TA = 25°C, unless otherwise noted. No Load Operating Current vs. Input Voltage (2x Mode) Input Voltage (V) Operating Current (mA) 5.0 5.2 5.4 5.6 5.8 6.0 6.2 6.4 85°C 25°C -40°C EN Input High Threshold Voltage vs. Input Voltage Input Voltage (V) VEN(H) (V) 0.2 0.4 0.6 0.8 1.0 1.2 85°C 25°C -40°C EN Input Low Threshold Voltage vs. Input Voltage Input Voltage (V) VEN(L) (V) 0.2 0.4 0.6 0.8 1.0 1.2 85°C 25°C -40°C EN/SET Input Latch Timeout vs. Input Voltage Input Voltage (V) TEN/SET(LAT) (µs) 150 180 210 240 270 300 330 85°C 25°C -40°C EN/SET Input OFF Timeout vs. Input Voltage Input Voltage (V) TEN/SET(OFF) (µs) 150 200 250 300 350 400 85°C 25°C -40°C

Low Cost 1x/2x Four-Channel Charge Pump WLED Driver Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com 202124A • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice. • July 2, 2012 Functional Description The AAT3104 is a low-cost charge-pump solution designed to drive up to four white LEDs. The charge pump operates from a 2.7V to 5.5V power source and converts it to voltage levels necessary to drive the LEDs. LED current is individually controlled through integrated current sources powered from the output of the charge pump. Low 1x charge-pump output resistance and low- drop voltage current sources allow the charge pump to remain in 1x mode with an input voltage as low as 3.8V and LED forward voltages of 3.5V. Once in 2x mode, the charge pump monitors the input supply voltage and automatically switches back to 1x mode when there is sufficient input voltage. The AAT3104 requires only three external components: one 1μF ceramic capacitor for the charge pump flying capacitor (CP), one 1μF ceramic input capacitor (CIN), one 1μF ceramic output capacitor (C OUT). The four constant current outputs of the AAT3104 (D1 to D4) can drive four individual LEDs with a maximum current of 30mA each. Skyworks' S2Cwire serial interface enables the AAT3104- 1/-2 and changes the current source magnitudes through the EN/SET pin. S2Cwire Serial Interface The LED output current of the AAT3104 is controlled by Skyworks' S2Cwire serial interface. Since the LED current is programmable, no PWM or additional control circuitry is needed to control LED brightness. This feature greatly reduces the burden on a microcontroller or system IC to manage LED or display brightness, allowing the user to “set it and forget it.” With its high-speed serial interface (1MHz data rate), the LED current can be changed quick- ly and easily. Also, the non-pulsating LED current reduc- Functional Block Diagram C–C+ OUT GND IN S2Cwire Control 5 Bits DACEN/SET Two-Mode CP Control VF Monitoring IREF5

Low Cost 1x/2x Four-Channel Charge Pump WLED Driver Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com 202124A • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice. • July 2, 2012 es system noise and improves LED reliability. The S2Cwire interface relies on the number of rising edges to the EN/ SET pin to set the register. A typical write protocol is a burst of EN/SET rising edges, followed by a pause with EN/SET held high for at least t LAT (500μs). The pro - grammed current is then seen at the current source out- puts. When EN/SET is held low for an amount of time longer than t OFF (500μs), the AAT3104 enters into shut - down mode and draws less than 1μA from the input and the internal data register is reset to zero. The AAT3104-1/2’s serial interface reduces the LED cur- rent on each rising pulse of the enable input. If the AAT3104 is in shutdown, the first rising edge of the EN/ SET input turns on the LED driver to the maximum cur - rent. Successive rising edges decrease the LED current as shown in Table 1 and Figure 2 for the AAT3104-1. For the AAT3104-2, Table 2 and Figure 3 illustrate a 32-step LED current control profile. Data EN Rising Edges D1-D4 Current (mA) 1 1 30 2 2 28 3 3 26 4 4 24 5 5 22 6 6 20 7 7 18 8 8 16 9 9 14 10 10 12 11 11 10 12 12 8 13 13 6 14 14 4 15 15 2 16 16 0.5 Table 1: AAT3104-1 LED Current Settings. Data EN Rising Edges D1-D4 Current (mA) 1 1 31 2 2 30 3 3 29 4 4 28 5 5 27 6 6 26 7 7 25 8 8 24 9 9 23 10 10 22 11 11 21 12 12 20 13 13 19 14 14 18 15 15 17 16 16 16 17 17 15 18 18 14 19 19 13 20 20 12 21 21 11 22 22 10 23 23 9 24 24 8 25 25 7 26 26 6 27 27 5 28 28 4 29 29 3 30 30 2 31 31 1 32 32 0.5 Table 2: AAT3104-2 LED Current Settings. 2 3OFFO FF tLO tOFFtHI Figure 1: EN/SET Timing Diagram.

Low Cost 1x/2x Four-Channel Charge Pump WLED Driver Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com 202124A • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice. • July 2, 2012 Applications Information LED Selection The AAT3104 is specifically designed for driving white LEDs. However, the device design will allow the AAT3104 to drive most types of LEDs with forward voltage speci - fications ranging from 2.2V to 4.7V. LED applications may include mixed arrangements for display backlight - ing, keypad display, and any other application needing a constant current source generated from a varying input voltage. Since the D1 to D4 constant current sources are matched with negligible supply voltage dependence, the constant current channels will be matched regardless of the specific LED forward voltage (VF) levels. The low dropout current sources in the AAT3104 maxi - mize performance and make it capable of driving LEDs with high forward voltages. Multiple channels can be combined to obtain a higher LED drive current without complication. All unused LED source pins should be connected to GND or left floating. Do not connect to the OUT pin. Device Switching Noise Performance The AAT3104 operates at a fixed frequency of approxi - mately 1MHz to control noise and limit harmonics that can interfere with the RF operation of mobile communi - cation devices. Back-injected noise appearing on the input pin of the charge pump is 20mV peak-to peak, typically ten times less than inductor-based DC/DC boost converter white LED backlight solutions. The AAT3104 soft-start feature prevents noise transient effects associ- ated with inrush currents during start-up of the charge pump circuit. Shutdown Since the current switches are the only power returns for all loads, there is no leakage current when all source switches are disabled. To enter shutdown operation, the EN/SET input for the AAT3104-1/2 should be strobed low. After tOFF (500μs), AAT3104 will be shut down and typically draws less than 1μA from the input. Registers are reset to 0 in shutdown. Power Efficiency and Device Evaluation The charge pump efficiency discussion in the following sections accounts only for efficiency of the charge pump section itself. Due to the unique circuit architecture and design of the AAT3104, it is very difficult to measure efficiency in terms of a percent value comparing input power over output power. Since the AAT3104 outputs are pure constant current sources and typically drive individual loads, it is difficult to measure the output voltage for a given output to derive an overall output power measurement. For any given application, white LED forward voltage levels can differ, yet the output drive current will be maintained as a constant. This makes quantifying output power a difficult task when taken in the context of comparing to other white LED driver circuit topologies. A better way to quantify total device efficiency is to observe the total input power to the device for a given LED current drive level. The best white LED driver for a given application should be based on trade-offs of size, external component count, reliability, operating range, and total energy usage, not just output power over input power efficiency. The AAT3104 efficiency may be quantified under very specific conditions and is dependent upon the input volt- age versus the output voltage across the loads applied S2C Wire Interface Data Code Dx Output Current (mA) 7.5 15.0 22.5 30.0 12 34 56 78 91 01 11 21 31 41 51 6 S2C Wire Interface Data Code Dx Output Current (mA) 1357 91 11 31 51 71 92 12 32 52 72 93 1 Figure 2: AAT3104-1 Current Control Profile. Figure 3: AAT3104-2 Current Control Profile.

Low Cost 1x/2x Four-Channel Charge Pump WLED Driver Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com 202124A • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice. • July 2, 2012 to outputs D1 through for a given constant current set - ting. Depending on the combination of V IN and voltages sensed at the current sources, the device will operate in load switch mode. When any one of the voltages sensed at the current sources nears dropout, the device will operate in 2X charge pump mode. Each of these modes will yield different efficiency values. Refer to the following two sections for explanations for each operational mode. 1X Mode Efficiency The AAT3104 1X mode is operational at all times and functions alone to enhance device power conversion effi- ciency when V IN is higher than the voltage across the load. When in 1X mode, voltage conversion efficiency is defined as output power divided by input power. An expression for the ideal efficiency ( η) in 1X charge- pump mode can be expressed as: POUT PIN VF · ILED VIN · IIN VF · ILED VIN · IOUT VF VIN η = = = ≈ -or V F V IN η (%) = · 100 For a charge pump led driver with V F of 3.2V and 4.2V input voltage, the theoretical efficiency is 76%. Due to internal switching losses and IC quiescent current con - sumption, the actual efficiency can be measured at 73%. 2X Charge Pump Mode Efficiency The AAT3104 contains a charge pump which will boost the input supply voltage in the event where V IN is less than the voltage required to supply the output. The effi- ciency ( η) can be simply defined as a linear voltage regulator with an effective output voltage that is equal to one and two times the input voltage. Efficiency (η) for an ideal 2X charge pump can typically be expressed as the output power divided by the input power. η = PF PIN In addition, with an ideal 2X charge pump, the output current may be expressed as 1/3 of the input current. The expression to define the ideal efficiency ( η) can be rewritten as POUT PIN VF · ILED VIN · IIN VF · ILED VIN · 2 · IOUT VF 2 · VIN η = = = ≈ or V F 2 · V IN η (%) = · 100 For a charge pump current source driver with VF of 3.2V and 2.7V input voltage, the theoretical efficiency is 59%. Due to internal switching losses and IC quiescent current consumption, the actual efficiency can be measured at 57%. Efficiency will decrease substantially as load cur - rent drops below 1mA or when the voltage level at V IN approaches the voltage level at VOUT. Additional Applications The current sources of the AAT3104 can be combined freely to drive higher current levels through one LED. As an example, a single LED can be driven at 120mA by combining together D1 through D4 outputs. For lower-cost applications, the flying capacitor can be removed; C+ and C- should be floating . This will force AAT3104 to operate in 1X mode. To maintain regulated LED current, the input supply voltage has to be higher than the charge-pump's dropout voltage in 1X mode plus the forward voltage of the LED at the preset LED current. Capacitor Selection Careful selection of the three external capacitors CIN, CP, and C OUT is important because they will affect turn-on time, output ripple, and transient performance. Optimum performance will be obtained when low equivalent series resistance (ESR) ceramic capacitors are used, in general, low ESR may be defined as less than 100mΩ. A value of 1μF for all four capacitors is a good starting point when choosing capacitors. If the constant current sources are only programmed for light current levels, then the capacitor size may be decreased. Capacitor Characteristics Ceramic composition capacitors are highly recommended over all other types of capacitors for use with the AAT3104. Ceramic capacitors offer many advantages over their tantalum and aluminum electrolytic counter - parts. A ceramic capacitor typically has very low ESR, is lowest cost, has a smaller PCB footprint, and is non- polarized. Low ESR ceramic capacitors help maximizing charge pump transient response. Since ceramic capaci - tors are non-polarized, they are not prone to incorrect connection damage.

Low Cost 1x/2x Four-Channel Charge Pump WLED Driver Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com 202124A • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice. • July 2, 2012

Ordering Information

Package Interface Current Control, Inverting Marking1 Part Number (Tape and Reel)2 SC70JW-10 S2Cwire 16-step AAT3104IJQ-1-T1 SC70JW-10 S2Cwire 32-step 4DXYY AAT3104IJQ-2-T1 Skyworks Green™ products are compliant with all applicable legislation and are halogen-free. For additional information, refer to Skyworks Definition of Green™, document number SQ04-0074.

Package Information

0.45 ± 0.10 0.05 ± 0.05 2.10 ± 0.30 4° ± 4° 0.15 ± 0.05 2.00 ± 0.20 7° ± 3° 0.85 ± 0.15

1.10 MAX

0.100 0.225 ± 0.075 1.75 ± 0.10 2.20 ± 0.20

0.40 BSC

All dimensions in millimeters. 1. XYY = assembly and date code. 2. Sample stock is generally held on part numbers listed in BOLD.

Low Cost 1x/2x Four-Channel Charge Pump WLED Driver Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com 202124A • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice. • July 2, 2012 Copyright © 2012 Skyworks Solutions, Inc. All Rights Reserved. Information in this document is provided in connection with Skyworks Solutions, Inc. (“Skyworks”) products or services. These materials, including the information contained herein, are provided by Skyworks as a service to its customers and may be used for informational purposes only by the customer. Skyworks assumes no responsibility for errors or omissions in these materials or the information contained herein. Sky - works may change its documentation, products, services, specifications or product descriptions at any time, without notice. Skyworks makes no commitment to update the materials or information and shall have no responsibility whatsoever for conflicts, incompatibilities, or other difficulties arising from any future changes. No license, whether express, implied, by estoppel or otherwise, is granted to any intellectual property rights by this document. Skyworks assumes no liability for any materials, products or information provided here- under, including the sale, distribution, reproduction or use of Skyworks products, information or materials, except as may be provided in Skyworks Terms and Conditions of Sale. THE MATERIALS, PRODUCTS AND INFORMATION ARE PROVIDED “AS IS” WITHOUT WARRANTY OF ANY KIND, WHETHER EXPRESS, IMPLIED, STATUTORY, OR OTHERWISE, INCLUDING FITNESS FOR A PARTICULAR PURPOSE OR USE, MERCHANTABILITY, PERFORMANCE, QUALITY OR NON-INFRINGEMENT OF ANY INTELLECTUAL PROPERTY RIGHT; ALL SUCH WARRANTIES ARE HEREBY EXPRESSLY DISCLAIMED. SKYWORKS DOES NOT WARRANT THE ACCURACY OR COMPLETENESS OF THE INFORMATION, TEXT, GRAPHICS OR OTHER ITEMS CONTAINED WITHIN THESE MATERIALS. SKYWORKS SHALL NOT BE LIABLE FOR ANY DAMAGES, IN - CLUDING BUT NOT LIMITED TO ANY SPECIAL, INDIRECT, INCIDENTAL, STATUTORY, OR CONSEQUENTIAL DAMAGES, INCLUDING WITHOUT LIMITATION, LOST REVENUES OR LOST PROFITS THAT MAY RESULT FROM THE USE OF THE MATERIALS OR INFORMATION, WHETHER OR NOT THE RECIPIENT OF MATERIALS HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. Skyworks products are not intended for use in medical, lifesaving or life-sustaining applications, or other equipment in which the failure of the Skyworks products could lead to personal injury, death, physical or en- vironmental damage. Skyworks customers using or selling Skyworks products for use in such applications do so at their own risk and agree to fully indemnify Skyworks for any damages resulting from such improper use or sale. Customers are responsible for their products and applications using Skyworks products, which may deviate from published specifications as a result of design defects, errors, or operation of products outside of pub- lished parameters or design specifications. Customers should include design and operating safeguards to minimize these and other risks. Skyworks assumes no liability for applications assistance, customer product design, or damage to any equipment resulting from the use of Skyworks products outside of stated published specifications or parameters. Skyworks, the Skyworks symbol, and “Breakthrough Simplicity” are trademarks or registered trademarks of Skyworks Solutions, Inc., in the United States and other countries. Third-party brands and names are for identification purposes only, and are the property of their respective owners. Additional information, including relevant terms and conditions, posted at www.skyworksinc.com, are incorporated by reference.