A2F-EVAL-KIT MICROSEMI | Alldatasheet
Document overview
- Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
- PDF pages: 4
Technical content
© 2012 Microsemi Corporation. All rights reserved. SmartFusion Evaluation Kit Quickstart Card Kit Contents – A2F-EVAL-KIT-2 Overview Microsemi’s SmartFusion Evaluation Kit provides designers access to SmartFusion customizable system-on-chip (SoC) FPGAs, the only devices that integrate an FPGA, an ARM® Cortex™-M3 processor, and programmable analog, offering full customization, IP protection, and ease-of-use. The device contains on-chip flash and on-chip SRAM memory, as well as additional SPI flash memory on the board. Quantity Description 1S m a r t F u s i o n® Evaluation board with A2F200M3F-FGG484 2 USB 2.0 A to mini-B cable Note: The A2F-EVAL-KIT-2 is RoHS compliant. 10/100 Ethernet Interface Regulators USB Program & Debug Interface SmartFusion Device User SW2 USB Power & USB-UART Interface Potentiometer Reset Switch J22 – Debug I/Os JP8 – UART Header JP9 – I2C Header JP11 – LED JP12 – LED JP13 – LED JP14 – LED JP7 – Debug Select JP10 – JTAG Select
8 User LEDs
OLED DisplayRVI – Header SPI-Flash Memory J23 – SPI Header PU_N Switch JP 6 – VRPSM Voltage Option
20 MHz
32.768 KHz
J24 – VAREFOUT/ VAREF Header User SW1 Mixed Signal Header
SmartFusion Evaluation Kit Quickstart Card Jumpers Settings, Programming, and Debug Prior to powering up the A2F-EVAL-KIT-2 for the first time, make sure the jumpers are in the following positions: Jumpers JP7 and JP10 control the programming and debug interaction with the SmartFusion device. JP8 is the UART header and JP9 is the I2C header. Jumpers JP11–JP14 control LED access. J23 is the SPI header. The UAR T and circuitry on the top left of the board replicate the functionality of the Microsemi standalone low-cost programming stick (LCPS) and provide the Microsemi programming and debug interface used with the FlashPro programming software and SoftConsole Integrated Design Environment (IDE) software. The R VI header on the board is used for communication through J-LINK or U-LINK for Keil™ and IAR Systems. The table below indicates how these settings can be used. Note: USB to UART for HyperT erminal is connected through the second UART connection and is not affected by these settings. For a full description of all jumpers, refer to the SmartFusion Evaluation Kit User’ s Guide. Jumper Location Purpose Setting J6 2 pins next to the Ethe rnet jack 3.3 V Regulator 1–2 JP6 Next to the PU_N switch VRPSM voltage option 2–3 JP7 Right side of board Input selecting option 1–2 JP10 Right side of boa rd JTAG programming option 1–2 JP11 Right side of boa rd Access to LED5 1–2 JP12 Right side of boa rd Access to LED6 1–2 JP13 Right side of boa rd Access to LED7 1–2 JP14 Right side of boa rd Access to LED8 1–2 J24 Bottom right side of board V AREFOUT/ V AREF Header 1–2, 3–4 Function Software Connector JP7 JP10 Debug Cortex-M3 SoftConsole J13 – USB PROG 1–2 (USB PROG) 2–3 (M3) Debug Cortex-M3 Keil or IAR J3 – R VI-HEADER 2–3 (R VI) 2–3 (M3) Debug FPGA Identify J13 – USB PROG 1–2 (USB PROG) 1–2 (FPGA) Programming FlashPro J13 – USB PROG 1–2 (USB PROG) 1–2 (FPGA)
SmartFusion Evaluation Kit Quickstart Card Running the Demo Design The SmartFusion Evaluation Kit comes with a preloaded demo design. If the board is programmed correctly, you will see the following message displayed on the OLED: Note: You may have to press the RESET or PUB switch to activate the demo design. The OLED will then update to show the following: If the board is not preprogrammed, the programming file and the source files for the demo are provided on the SmartFusion Evaluation Kit page. The programming file for the demo is provided standalone as a zip file under the SmartFusion Evaluation Kit Quickstart Card. The source files are posted with the SmartFusion Webserver Demo Using uIP and FreeRTOS document: www.microsemi.com/soc/products/hardware/devkits_boards/smartfusion_eval.aspx Running the Manufacturing Test You can run the manufacturing test to verify the device and board connections. The manufacturing test files are available from the SmartFusion Evaluation Kit web page. Instructions on how to run the test are available in the SmartFusion Evaluation Kit User's Guide.
50200210-4/8.12 SmartFusion Evaluation Kit Quickstart Card Software and Licensing The SmartFusion Evaluation Kit is supported by Libero® System-on-Chip (SoC) v10.0 or later, which includes a web install option. SoftConsole Software IDE and FlashPro are enabled by default in the web install; these software tools can be used for software design and debug. SmartFusion is also supported by Keil and IAR Systems, which can be installed separately. Refer to the SmartFusion Evaluation Kit User’ s Guide for more information. Software releases: www.microsemi.com/download/software/libero Keil and IAR information: www.microsemi.com/soc/products/smartfusion/ecosystem.aspx Libero SoC v10.0 requires a valid Gold, Platinum, or Standalone Libero license. If you need a new license, select FREE Libero SoC Gold license and request a new one from your Microsemi Customer Portal account. This license supports all tools for designing with the SmartFusion family and associated development kits. License updates: www.microsemi.com/soc/Portal/default.aspx?r=1 Documentation Resources For further kit information, including user's guide, tutorial, and full design examples, refer to the SmartFusion Evaluation Kit page: Documentation: www.microsemi.com/soc/products/hardware/devkits_boards/ smartfusion_eval.aspx As new demos and tutorials become available, they will be posted on the SmartFusion Evaluation Kit. Microsemi recommends that you sign up for Product Updates to be notified when new material is available. You can sign up for product updates from your Microsemi Customer Portal account. Product updates: https://www.actel.com/portal/default.aspx?r=2 Technical Support and Contacts Technical support is available online at www.microsemi.com/soc/support and by email at soc_tech@microsemi.com. Microsemi SoC Sales offices, including Representatives and Distributors, are located worldwide. To find your local representative visit www.microsemi.com/soc/company/contact.