A24C02 AITSEMI | Alldatasheet
Document overview
- Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
- PDF pages: 19
Technical content
AiT Semiconductor Inc. www.ait-ic.com A24C02 MEMORY EEPROM 2k BITS (256BYTES) TWO-WIRE SERIAL REV3.0 - SEP 2008 RELEASED, SEP 2018 UPDATED - - 1 - DESCRIPTION FEATURES The A24C02 provides 2048 bits of serial electrically erasable and programmable read -only memory (EEPROM), organized as 256 words of 8 bits each. The device is optimized for use in many industrial and commercial applications where l ow-power and low-voltage operation are essential. The A24C02 is available in SOP8, TSSOP8, DFN8, DIP8 and TSOT-25 packages. Compatible with all I2C bidirectional data transfer protocol Memory array: 2k bits (256bytes) of EEPROM Page size: 16 bytes Single supply voltage and high speed:
1 MHz
Random and sequential Read modes Write: Byte Write within 3 ms Page Write within 3 ms Partial Page Writes Allowed Write Protect Pin for Hardware Data Protection Schmitt Trigger , Filtered Inputs for Noise Suppression High-reliability Endurance: 1 Million Write Cycles Data Retention: 100 Years Enhanced ESD/Latch-up protection HBM 6000V Available in SOP8, TSSOP8, DFN8, DIP8 and TSOT-25 Packages
ORDERING INFORMATION
SPQ: 2,500pcs/Reel SPQ: 100pcs/Tube A24C02M8R A24C02M8U A24C02M8VR A24C02M8VU TSSOP8 SPQ: 3,000pcs/Reel SPQ: 100pcs/Tube TMX8 A24C02TMX8R A24C02TMX8U A24C02TMX8VR A24C02TMX8VU DFN8 SPQ: 3,000pcs/Reel J8 A24C02J8R A24C02J8VR DIP8 SPQ: 50pcs/Tube P8 A24C02P8U A24C02P8VU TSOT-25 SPQ: 3,000pcs/Reel TE5 A24C02TE5R A24C02TE5VR Note V: Halogen free Package R: Tape & Reel U: Tube AiT provides all RoHS products
AiT Semiconductor Inc. www.ait-ic.com A24C02 MEMORY EEPROM 2k BITS (256BYTES) TWO-WIRE SERIAL REV3.0 - SEP 2008 RELEASED, SEP 2018 UPDATED - - 2 - PIN DESCRIPTION Top View Top View Top View Top View Top View Pin # Symbol Type Functions SOP8 TSSOP8 DFN8 DIP8 TSOT-25 1 1 1 1 - A0 I Address Input 2 2 2 2 - A1 I Address Input 3 3 3 3 - A2 I Address Input 4 4 4 4 2 GND P Ground 5 5 5 5 3 SDA I/O Serial Data 6 6 6 6 1 SCL I Serial Clock Input 7 7 7 7 5 WP I Write Protect 8 8 8 8 4 VCC P Power Supply
AiT Semiconductor Inc. www.ait-ic.com A24C02 MEMORY EEPROM 2k BITS (256BYTES) TWO-WIRE SERIAL REV3.0 - SEP 2008 RELEASED, SEP 2018 UPDATED - - 3 - ABSOLUTE MAXIMUM RATINGS DC Supply Voltage -0.3V ~ +6.5V Input / Output Voltage GND-0.3V ~ VCC +0.3V Operating Ambient Temperature -40℃ ~ +85℃ Storage Temperature -65℃ ~ +150℃ Electrostatic Pulse (Human Body Model) 6000V Stress beyond above listed “Absolute Maximum Ratings” may lead permanent damage to the device. These are stress ratings only and operations of the device at these or any other conditions beyond those indicated in the operational sections of the specifications are not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. PIN CAPACITANCE Applicable over recommended operating range from: TA = 25℃, f = 1.0MHz, VCC = +1.7V Parameter Symbol Condition Min. Typ. Max. Unit Input / Output Capacitance (SDA) CI/O VI/O=0V - - 8 pF Input Capacitance (A0, A1, A2, SCL) CIN VIN=0V - - 6 pF
AiT Semiconductor Inc. www.ait-ic.com A24C02 MEMORY EEPROM 2k BITS (256BYTES) TWO-WIRE SERIAL REV3.0 - SEP 2008 RELEASED, SEP 2018 UPDATED - - 4 - DC ELECTRICAL CHARACTERISTICS Applicable over recommended operating range from: TA = -40℃ to +85℃, VCC = +1.7V to +5.5V, unless otherwise noted Parameter Symbol Condition Min. Typ. Max. Unit Supply Voltage VCC1 1.7 - 5.5 V Supply Current VCC = 5.0V ICC1 Read at 400kHz - 0.14 0.3 mA Supply Current VCC = 5.0V ICC2 Write at 400kHz - 0.28 0.5 mA Supply Current VCC = 5.0V ISB1 VIN = VCC or VSS - 0.03 0.5 μA Input Leakage Current ILI VIN = VCC or VSS - 0.10 1.0 μA Output Leakage Current ILO VOUT = VCC or VSS - 0.05 1.0 μA Input Low Level VIL1 VCC = 1.7V to 5.5V -0.3 - VCC x 0.3 V Input High Level VIH1 VCC = 1.7V to 5.5V VCC x0.7 - VCC + 0.3 V Output Low Level VCC = 1.7V VOL1 IOL = 0.15mA - - 0.2 V Output Low Level VCC = 5.0V VOL2 IOL = 3.0mA - - 0.4 V AC ELECTRICAL CHARACTERISTICS Applicable over recommended operat ing range from: T A = -40℃ to +85℃, VCC = +1.7V to +5.5V, C L = 1 TTL Gate and 100pF, unless otherwise noted Clock Frequency, SCL fSCL - - 400 - - 1000 kHz Clock Pulse Width Low tLOW 0.6 - - 0.6 - - μs Clock Pulse Width High tHIGH 0.4 - - 0.4 - - μs Noise Suppression Time tI - - 50 - - 50 ns Clock Low to Data Out Valid tAA 0.1 - 0.55 0.1 - 0.55 μs Time the bus must be free before a new transmission can start tBUF 0.5 - - 0.5 - - μs Start Hold Time tHD.STA 0.25 - - 0.25 - - μs Start Setup Time tSU.STA 0.25 - - 0.25 - - μs Data In Hold Time tHD.DAT 0 - - 0 - - μs Data In Setup Time tSU.DAT 100 - - 100 - - ns Inputs Rise TimeNOTE1 tR - - 0.3 - - 0.3 μs Inputs Fall TimeNOTE1 tF - - 0.3 - - 0.3 μs Stop Setup Time tSU.STO 0.25 - - 0.25 - - μs Data Out Hold Time tDH 50 - - 50 - - ns Write Cycle Time tWR - 1.9 3 - 1.9 3 ms 5.0V, 25℃, Byte ModeNOTE1 Endurance 1M - - - - - Write Cycles NOTE1: This parameter is characterized and is not 100% tested. NOTE2: AC measurement conditions: RL(connects to VCC): 1.3kΩ Input pulse voltages: 0.3 VCC to 0.7VCC Input rise and fall time: 50ns Input and output timing reference voltages: 0.5VCC The value of RL should be concerned according to the actual loading on the user’s system.
AiT Semiconductor Inc. www.ait-ic.com A24C02 MEMORY EEPROM 2k BITS (256BYTES) TWO-WIRE SERIAL REV3.0 - SEP 2008 RELEASED, SEP 2018 UPDATED - - 5 - BLOCK DIAGRAM
AiT Semiconductor Inc. www.ait-ic.com A24C02 MEMORY EEPROM 2k BITS (256BYTES) TWO-WIRE SERIAL REV3.0 - SEP 2008 RELEASED, SEP 2018 UPDATED - - 6 - DETAILED INFORMATION DEVICE/PAGE ADDRESSES (A2, A1 and A0): The A2, A1 and A0 pins are device address inputs that are hard wire for the A24C02. Eight 2 k devices may be addressed on a single bus system (device addres sing is discussed in detail under the Device Addressing section). SERIAL DATA (SDA): The SDA pin is bi-directional for serial data transfer. This pin is open -drain driven and may be wire-ORed with any number of other open-drain or open- collector devices. SERIAL CLOCK (SCL): The SCL input is used to positive edge clock data into each EEPROM device and negative edge clock data out of each device. WRITE PROTECT (WP): The A24C02 has a Write Protect pin that provides hardware data protection. The Write Pro tect pin allows normal read/write operations when connected to ground (GND). When the Write Protection pin is connected to V CC, the write protection feature is enabled and operates as shown in the following Table 1. Table1: Write Protect WP Pin Status A24C02 At VCC Full(2k)Array At GND Normal Read/Write Operations
AiT Semiconductor Inc. www.ait-ic.com A24C02 MEMORY EEPROM 2k BITS (256BYTES) TWO-WIRE SERIAL REV3.0 - SEP 2008 RELEASED, SEP 2018 UPDATED - - 7 - FUNCTIONAL DESCRIPTION 1. Memory Organization A24C02, 2k SERIAL EEPROM: Internally organized with 1 6 pages of 16 bytes each, the 2k requires a 8 -bit data word address for random word addressing. 2. Device Operation CLOCK and DATA TRANSITIONS: The SDA pin is normally pulled high with an external device. Data on the SDA pin may change only during SCL low time periods ( see Figure 1 on page 10). Data changes during SCL high periods will indicate a start or stop condition as defined below. START CONDITION: A high-to-low transition of SDA with SCL high is a start condition which must precede any other command (see Figure 2 on page 10). STOP CONDITION: A low-to-high transition of SDA with SCL high is a stop condition. After a read sequence, the stop command will place the EEPROM in a standby power mode (see Figure 2 on page 10). ACKNOWLEDGE: All addresses and data words are serially transmitted to and from the EEPROM in 8 -bit words. The EEPROM sends a "0" to acknowledge that it has received each word. This happens during the ninth clock cycle. STANDBY MODE: The A24C02 features a low -power standby mode which is enabled: (a) upon power -up and (b) after the receipt of the STOP bit and the completion of any internal operations. MEMORY RESET: After an interruption in protocol, power loss or system reset, any two -wire part can be reset by following these steps: 1. Clock up to 9 cycles. 2. Look for SDA high in each cycle while SCL is high. 3. Create a start condition.
AiT Semiconductor Inc. www.ait-ic.com A24C02 MEMORY EEPROM 2k BITS (256BYTES) TWO-WIRE SERIAL REV3.0 - SEP 2008 RELEASED, SEP 2018 UPDATED - - 8 - 3. Device Addressing The 2k EEPROM devices all require an 8 -bit device address word following a start condition to enable the chip for a read or write operation (see Figure 4 on page11) The device address word consists of a mandatory "1", "0" sequence for the first four most significant bits as shown. This is common to all the Serial EEPROM devices. The 2k EEPROM uses A2, A1 and A0 device address bits to allow as much as eight devices on the same bus. These 3 bits must be compared to their correspondin g hardwired input pins. The A2, A1 and A0 pins use an internal proprietary circuit that biases them to a logic low condition if the pins are allowed to float. The eighth bit of the device address is the read/write operation select bit. A read operation is initiated if this bit is high and a write operation is initiated if this bit is low. Upon a compare of the device address, the EEPROM will output a "0". If a compare is not made, the chip will return to a standby state. DATA SECURITY: The A24C02 has a hardware data protection scheme that allows the user to write protect the entire memory when the WP pin is at VCC. 4. Write Operations BYTE WRITE: A write operation requires an 8 -bit data word address following the device address word and acknowledgment. Upon receipt of this address, the EEPROM will again respond with a "0" and then clock in the first 8 -bit data word. Following receipt of the 8 -bit data word, the EEPROM will output a "0" and the addressing device, such as a microcontroller, must terminate the write sequence with a stop condition. At this time the EEPROM enters an internally timed write cycle, t WR, to the nonvolatile memory. All inputs are disabled during this write cycle and the EEPROM will not respond until the write is complete (see Figure 6 on page11). PAGE WRITE: The 2k EEPROM is capable of an 16 -byte page write. A page write is initiated the same as a byte write, but the microcontroller does not send a stop condition after the first data word is clocked in. Instead, after the EEPROM acknow ledges receipt of the first data word, the microcontroller can transmit up to seven more data words. The EEPROM will respond with a "0" after each data word received. The microcontroller must terminate the page write sequence with a stop condition (see Figure 7 on page11). The data word address lower three bits are internally incremented following the receipt of each data word. The higher data word address bits are not incremented, retaining the memory page row location. When the word address, internally generated, reaches the page boundary, the following byte is placed at the beginning of the same page. If more than eight data words are transmitted to the EEPROM, the data word address will "roll over" and previous data will be overwritten.
AiT Semiconductor Inc. www.ait-ic.com A24C02 MEMORY EEPROM 2k BITS (256BYTES) TWO-WIRE SERIAL REV3.0 - SEP 2008 RELEASED, SEP 2018 UPDATED - - 9 - ACKNOWLEDGE POLLING: Once the internally timed write cycle has started and the EEPROM inputs are disabled, acknowledge polling can be initiated. This involves sending a start condition followed by the device address word. The read/write bit is representative of the operat ion desired. Only if the internal write cycle has completed will the EEPROM respond with a "0", allowing the read or write sequence to continue. 5. Read Operations Read operations are initiated the same way as write operations with the exception that the rea d/write select bit in the device address word is set to "1". There are three read operations: current address read, random address read and sequential read. CURRENT ADDRESS READ: The internal data word address counter maintains the last address accessed during the last read or write operation, incremented by one. This address stays valid between operations as long as the chip power is maintained. The address "roll over" during read is from the last byte of the last memory page to the first byte of the fir st page. The address "roll over" during write is from the last byte of the current page to the first byte of the same page. Once the device address with the read/write select bit set to "1" is clocked in and acknowledged by the EEPROM, the current address data word is serially clocked out. The microcontroller does not respond with an input "0" but does generate a following stop condition (see Figure 8 on page12). RANDOM READ: A random read requires a "dummy" byte write sequence to load in the data word add ress. Once the device address word and data word address are clocked in and acknowledged by the EEPROM, the microcontroller must generate another start condition. The microcontroller now initiates a current address read by sending a device address with the read/write select bit high. The EEPROM acknowledges the device address and serially clocks out the data word. The microcontroller does not respond with a "0" but does generate a following stop condition (see Figure 9 on page12) SEQUENTIAL READ: Sequential reads are initiated by either a current address read or a random address read. After the microcontroller receives a data word, it responds with an acknowledge. As long as the EEPROM receives an acknowledge, it will continue to increment the data word add ress and serially clock out sequential data words. When the memory address limit is reached, the data word address will "roll over" and the sequential read will continue. The sequential read operation is terminated when the microcontroller does not respond with a "0" but does generate a following stop condition (see Figure 10 on page12).
AiT Semiconductor Inc. www.ait-ic.com A24C02 MEMORY EEPROM 2k BITS (256BYTES) TWO-WIRE SERIAL REV3.0 - SEP 2008 RELEASED, SEP 2018 UPDATED - - 14 -
PACKAGE INFORMATION
Dimension in SOP8 (Unit: mm) Symbol Min Max A 1.35 1.75 A1 0.10 0.25 b 0.31 0.51 C 0.17 0.25 D 4.80 5.00 E1 3.81 3.99 E 5.79 6.20 e 1.27BSC L 0.40 1.27 θ 0° 8°
AiT Semiconductor Inc. www.ait-ic.com A24C02 MEMORY EEPROM 2k BITS (256BYTES) TWO-WIRE SERIAL REV3.0 - SEP 2008 RELEASED, SEP 2018 UPDATED - - 15 - Dimension in TSSOP8 Package (Unit: mm) Symbol Min Max D 2.90 3.10 E 6.40 BSC E1 4.30 4.50 A - 1.20 A2 0.80 1.05 b 0.19 0.30 e 0.65 BSC L 0.45 0.75 L1 1.00 REF
AiT Semiconductor Inc. www.ait-ic.com A24C02 MEMORY EEPROM 2k BITS (256BYTES) TWO-WIRE SERIAL REV3.0 - SEP 2008 RELEASED, SEP 2018 UPDATED - - 16 - Dimension in DFN8 (Unit: mm) Symbol Min Max A >0.50 0.60 A1 0.00 0.05 A3 0.15 REF. D 1.95 2.05 E 2.95 3.05 b 0.20 0.30 L 0.20 0.40 D2 1.25 1.50 E2 1.15 1.40 e 0.50 BSC
AiT Semiconductor Inc. www.ait-ic.com A24C02 MEMORY EEPROM 2k BITS (256BYTES) TWO-WIRE SERIAL REV3.0 - SEP 2008 RELEASED, SEP 2018 UPDATED - - 17 - Dimension in DIP8 (Unit: inches) Symbol Min Max A - 0.210 A2 0.115 0.195 b 0.014 0.022 b2 0.045 0.070 b3 0.030 0.045 c 0.008 0.014 D 0.355 0.400 D1 0.005 - E 0.300 0.325 E1 0.240 0.280 e 0.100 BSC eA 0.300 BSC L 0.115 0.150
AiT Semiconductor Inc. www.ait-ic.com A24C02 MEMORY EEPROM 2k BITS (256BYTES) TWO-WIRE SERIAL REV3.0 - SEP 2008 RELEASED, SEP 2018 UPDATED - - 18 - Dimension in TSOT-25 (Unit: mm) Symbol Min. Max. A - 0.90 A1 0.00 0.15 A2 0.65 0.85 A3 0.35 0.45 c 0.14 0.20 c1 0.14 0.16 D 2.85 3.05 E 2.65 2.95 E1 1.60 1.70 e 0.90 1.00 e1 1.80 2.00 L 0.30 0.60 L1 0.575REF L2 0.258BSC R - 0.25 R1 - 0.25 θ 0° 8° θ1 3° 7° θ2 10° 14°
AiT Semiconductor Inc. www.ait-ic.com A24C02 MEMORY EEPROM 2k BITS (256BYTES) TWO-WIRE SERIAL REV3.0 - SEP 2008 RELEASED, SEP 2018 UPDATED - - 19 - IMPORTANT NOTICE AiT Semiconductor Inc. (AiT) reserves the right to make changes to any its product, specifications, to discontinue any integrate d circuit product or service without notice, and advises its customers to obtain the latest version of relevant information to verify, before placing orders, that the information being relied on is current. AiT Semiconductor Inc. 's integrated circuit pro ducts are not designed, intended, authorized, or warranted to be suitable for use in life support applications, devices or systems or other critical applications. Use of AiT products in such applications is understood to be fully at the risk of the custom er. As used herein may involve potential risks of death, personal injury, or serv er property, or environmental damage. In order to minimize risks associated with the customer's applications, the customer should provide adequate design and operating safeguards. AiT Semiconductor Inc . assumes to no liability to customer product design or application support. AiT warrants the performance of its products of the specifications applicable at the time of sale.