9700 SENSATA | Alldatasheet
Document overview
- Manufacturer or author: Provided By alldatasheet.com(free datasheet download site)
- PDF pages: 4
Technical content
www.sensata.com Copyright © 2018 Sensata Technologies, Inc.
9700 PROTECTOR
THERMAL PROTECTOR FOR MOTOR/FLUORESCENT BALLASTS AND TEMPERATURE SENSING CONTROLS TECHNICAL SPECIFICATIONS Introduction The Klixon® 9700 protector is a field proven miniature protector developed to protect shaded pole and permanent split capacitor motors, fluorescent ballasts, solenoids, transformers and other electrical equipment against overheating. In addition to being small and lightweight, the unit is both temperature and current sensitive. Since the 9700 is sealed to withstand varnish dipping, it can be mounted directly in windings where it can best sense the true temperature of the electrical equipment. As a result, over-temperature protection is assured. Since the case is not electrically insulated, the protector is furnished with a durable Mylar insulating sleeve. Shrinkable and non-shrinkable sleeves are available. Purpose of the Control Thermal Motor Protector (TMP) Thermal Ballast Protector (TBP) Thermal Cut-Out (TCO) Contact Capacity 250VAC 13A for TCO 250VAC 2A for TBP Temperature Range 60°C to 150°C for TCO and TMP 60°C to 135°C for TBP Tolerance on Open Temp. +/- 5K or +/- 8K Automatic Action Type 3C for TMP Type 2C for TBP and TCO Operating Time Continuous Pollition Station Normal Extent of Sensing Element Whole Control PTI of the Insulation 175 Enclosure Protection Degree IP00
www.sensata.com Page 2 Copyright © 2018 Sensata Technologies, Inc. CURVES Dimensions in mm [Inch] DIMENSIONS
www.sensata.com Page 3 Copyright © 2018 Sensata Technologies, Inc. ORDERING OPTIONS Example : 9700K01-215 Bimetal of 30 ohms/cmf, 120°C Operating Temperature, ±5K Tolerance with AWG#18 (UL3343 125°C -600V), 66.7mm Length Leads, Thick 0.15mm, Dia. 6.9mm, Legnth 34mm, Mylar Sleeve. Device Identification Contact Material Combination Open Temperature Tolerance Operating Temperature and Actuation Disc Material Wire Lead and Sleeve 9700 Serial Number is assigned for each desired temperature and reistance rating. Code Stationaly Contact Movable Contact K AgNi + Silver Cadmium Oxide Steel + Copper + Silver Cadmium Oxide H Brass + Fine Silver Steel + Copper + Silver Cadmium Oxide Note: We only provide H / K Type Devices. K type when new parr number is defined and setup. : ± 5K, 2: ±8K Serial Number is assigned for each desired temperature and reistance rating. Nominal Operating Temperature Resistance of Actuation Disc (ohms.cmf) 30 250 850 100 475 Temperature Code 60 56 57 58 59 60 80 91 92 93 94 95 90 21 22 23 24 25 100 26 27 28 29 30 110 36 37 38 39 40 120 1 2 3 4 5 130 11 12 13 14 15 140 66 67 68 69 70 150 46 47 48 49 50 This is a typical temperature code. There is a temperature code at each 5°C in a step from 60 to 150°C Serial number is assigned for each lead and sleeve configuration, i.e. wire type, length, AWG#, stripped length, sleeve type, and length.
9700 X X YY ZZZZ
www.sensata.comCopyright © 2018 Sensata Technologies, Inc. Sensata Technologies, Inc. (“Sensata”) data sheets are solely intended to assist designers (“Buyers”) who are developing systems that incorporate Sensata products (also referred to herein as “components”). Buyer understands and agrees that Buyer remains responsible for using its independent analysis, evaluation and judgment in designing Buyer’s systems and products. Sensata data sheets have been created using standard laboratory conditions and engineering practices. Sensata has not conducted any testing other than that specifically described in the published documentation for a particular data sheet. Sensata may make corrections, enhancements, improvements and other changes to its data sheets or components without notice. Buyers are authorized to use Sensata data sheets with the Sensata component(s) identified in each particular data sheet. HOWEVER, NO OTHER LICENSE, EXPRESS OR IMPLIED, BY ESTOPPEL OR OTHERWISE TO ANY OTHER SENSATA INTELLECTUAL PROPERTY RIGHT, AND NO LICENSE TO ANY THIRD PARTY TECHNOLOGY OR INTELLECTUAL PROPERTY RIGHT, IS GRANTED HEREIN. SENSATA DATA SHEETS ARE PROVIDED “AS IS”. SENSATA MAKES NO WARRANTIES OR REPRESENTATIONS WITH REGARD TO THE DATA SHEETS OR USE OF THE DATA SHEETS, EXPRESS, IMPLIED OR STATUTORY , INCLUDING ACCURACY OR COMPLETENESS. SENSATA DISCLAIMS ANY WARRANTY OF TITLE AND ANY IMPLIED WARRANTIES OF MERCHANTABILITY , FITNESS FOR A PARTICULAR PURPOSE, QUIET ENJOYMENT, QUIET POSSESSION, AND NON-INFRINGEMENT OF ANY THIRD PARTY INTELLECTUAL PROPERTY RIGHTS WITH REGARD TO SENSATA DATA SHEETS OR USE THEREOF. All products are sold subject to Sensata’s terms and conditions of sale supplied at www.sensata.com SENSATA ASSUMES NO LIABILITY FOR APPLICATIONS ASSISTANCE OR THE DESIGN OF BUYERS’ PRODUCTS. BUYER ACKNOWLEDGES AND AGREES THAT IT IS SOLELY RESPONSIBLE FOR COMPLIANCE WITH ALL LEGAL, REGULATORY AND SAFETY-RELATED REQUIREMENTS CONCERNING ITS PRODUCTS, AND ANY USE OF SENSATA COMPONENTS IN ITS APPLICATIONS, NOTWITHSTANDING ANY APPLICATIONS-RELATED INFORMATION OR SUPPORT THAT MAY BE PROVIDED BY SENSATA. Mailing Address: Sensata Technologies, Inc., 529 Pleasant Street, Attleboro, MA 02703, USA. CONTACT US Revised 03/21/18 Americas +1 (508) 236-2551 electrical-protection-sales@ sensata.com Europe, Middle East & Africa +3 174 357 8156 info-sse@list.sensata.com Asia Pacific sales.isasia@list.sensata.com China +86 (21) 2306 1500 Japan +81 (45) 277 7117 Korea +82 (31) 601 2004 India +91 (80) 67920890 Rest of Asia +886 (2) 27602006 ext 2808 Agency File Number Standard Note UL E 15962 UL2111 Motor protector ENEC 2014531.10 EN60730-2-9 Thermal cut-out ENEC 2014531.10 EN60730-2-2 Thermal motor protector ENEC 2014531.10 EN60730-2-3 Thermal Ballast Protector CQC CQC0200 2001344 AGENCY APPROVALS & CERTIFICATIONS