972-0070 DURATOOL | Alldatasheet
Document overview
- Manufacturer or author: Provided By alldatasheet.com(free datasheet download site)
- PDF pages: 2
Technical content
Page <1> 15/11/11 V1.1 www.element14.com www.farnell.com www.newark.com www.cpc.co.uk www.mcmelectronics.com Description Pilot Hole Bolt Size Thrust Bearing Part Number Metric Round Sizes Circular Hand Hole Cutter, 12.5mm 10 8 NA 970-0010 Circular Hand Hole Cutter, 14.5mm 970-0020 Circular Hand Hole Cutter, 16.5mm 970-0030 Circular Hand Hole Cutter, 18mm 12 10 970-0050 M10 Circular Hand Hole Cutter, 20mm 970-0060 M10 Circular Hand Hole Cutter, 22.5mm 970-0070 M10 Circular Hand Hole Cutter, 25mm 970-0080 M10 Circular Hand Hole Cutter, 27.5mm Yes 970-0090 M10 Circular Hand Hole Cutter, 30mm 14.5 12 970-0100 Specification Table The friction reducing thrust bearings make hole punching effortless. Reducing force required by approximately 65% All hole cutters can be used with hydraulic kit 940-0000 Punches and dies are made from case hardened steel to give reduce wear and give long life Special sizes available on request Features:
- • A complete easy to use system enabling a wide variety of hole configurations to be punched by hand
- • Suitable for sheet steel, stainless, non-ferrous metals and plastics
- • Ideal for switchgear manufacturers, electricians, plumbers and handi-crafters
- • Heat treated steel punches and dies manufactured to close tolerances will punch burr free holes up to 2 mm thick in steel and 3 mm thick in aluminium
Page <2> 15/11/11 V1.1 www.element14.com www.farnell.com www.newark.com www.cpc.co.uk www.mcmelectronics.com Important Notice : This data sheet and its contents (the "Information") belong to the members of the Premier Farnell group of companies (the "Group") or are licensed to it. No licence is granted for the use of it other than for information purposes in connection with the products to which it relates. No licence of any intellectual property rights is granted. The Information is subject to change without notice and replaces all data sheets previously supplied. The Information supplied is believed to be accurate but the Group assumes no responsibility for its accuracy or completeness, any error in or omission from it or for any use made of it. Users of this data sheet should check for themselves the Information and the suitability of the products for their purpose and not make any assumptions based on information included or omitted. Liability for loss or damage resulting from any reliance on the Information or use of it (including liability resulting from negligence or where the Group was aware of the possibility of such loss or damage arising) is excluded. This will not operate to limit or restrict the Group's liability for death or personal injury resulting from its negligence. DURATOOL is the registered trademark of the Group. © Premier Farnell plc 2011. Description Pilot Hole Bolt Size Thrust Bearing Part Number Metric Round Sizes M12 Circular Hand Hole Cutter, 35mm 14.5 12 Yes 970-0110 M16 Circular Hand Hole Cutter, 50mm 20 16 970-0130 M16 Circular Hand Hole Cutter, 60mm 970-0140 M16 Circular Hand Hole Cutter, 70mm 970-0150 Imperial Round Sizes M10 Circular Hand Hole Cutter, 1 1/4 Inches 12 10 NA 971-0040 M12 Circular Hand Hole Cutter, 1 1/2 Inches 14.5 12 Yes 971-0050 M16 Circular Hand Hole Cutter, 1 3/4 Inches 20 16 971-0060 Square Series Sizes M10 Square Hand Hole Cutter, 19.1mm 14.5 10 Yes 972-0040 M10 Circular Hand Hole Cutter, 12.6mm 10 8 972-0050 M10 Circular Hand Hole Cutter, 15.1mm 972-0060 M12 Circular Hand Hole Cutter, 32.5mm 16.5 12 972-0070 Specification Table