961103-6404-AR

IDTF0552NLGI IDT | Alldatasheet

Document overview

Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
PDF pages: 54

Technical content

Sampling IF Receiver 1710MHz to 2050MHz FlatNoiseTM, Zero-DistortionTM, SIF Rx 1 Rev2, January 2014 IDTF0552NLGI Datasheet F0552NBGI Advance Datasheet GENERAL DESCRIPTION This document describes the specifications for the IDTF0552 1710MHz to 2050MHz dual path Sampling Intermediate Frequency (SIF) Receiver ideal for Multi- mode, Multi-carrier BaseStation Receivers. Refer to the Part # Matrix below describing the frequency coverage of the complete series. This series of devices covers all UTRA bands up to 2.7 GHz and offers significantly better Noise and Distortion performance than currently available solutions. IF frequencies up to 450 MHz are supported. The IDTF0552 SIF provides 29dB gain and offers 47dB gain adjustment in 1dB steps designed to operate with a single 5V supply. Nominally, the device offers +45 dBm Output IP3 using 450mA of ICC. Alternately one can configure the device in low current (LC) mode to reduce power consumption to < 1.9 Watts. This device is packaged in a 10x10 68-pin Thin QFN with 50 ohm single-ended RF input and 200 ohm differential IF output impedances for ease of integration into the receiver lineup. The EvKit is configured to match the 200 ohm differential IF output to 100 ohms differential for a broad range of IF center frequencies per the application drawings on page 51. COMPETITIVE ADVANTAGE IDT’s Zero-DistortionTM mixer in combination with interstage filtering and IDT’s proprietary FlatNoiseTM DVGA improves system SNR to the point where the external SAW filter can be eliminated. Both IP3O & NF are kept virtually flat while gain is backed off, enhancing SNR significantly under high level interferer conditions, and greatly benefiting 2G/3G/4G Multi-Carrier IF sampling receivers. In addition, total power consumption is reduced by ~35% compared to conventional solutions.  No external SAW is needed  Reduced Power Consumption by 35%  NF and OIP3 virtually flat for first 17 dB gain reduction The fast-settling, parallel mode gain step of 1.0 dB coupled with the excellent differential non-linearity allow for SNR to be maximized further by targeting the minimum necessary gain in small, accurate increments. The matched output does not require a terminating resistor, thus the gain and distortion performance are preserved when driving Bandpass Anti-Alias filters.

FEATURES

 Dual Channel for Diversity / MIMO Systems  Combines FlatNoiseTM and Zero-DistortionTM technology  29 dB Total Power Gain  47 dB gain control range  1 dB Gain Steps  Ultra linear +45 dBm IP3O  Low NF: 9.6 dB @ GMAX  50 Ω input impedance  Matched to 100 Ω differential output impedance  Ultra high +19.8 dBm P1dBo  Independent channel standby mode  Constant LO impedance in STBY mode  6 bit parallel control  60 MHz to 450 MHz IF frequency range  Excellent 2x2, 3x3, IM2, 2nd Harmonic Rejection  ICC = 450mA STD Mode, 375mA LC Mode  10x10 68-pin TQFN package DEVICE BLOCK DIAGRAM PART# MATRIX Part# RF freq range UTRA bands IF freq range Typ. Gain Injection F0502 698 - 915 5,6,8,12,13,14,17 18,19,20 60 – 300 29 Low & High Side F0552 1710 - 2050 1,2,3,4,9,10,23, 25,33,34,35,36, 37,39 60 – 450 29 Low & High Side F0562 2300 – 2700 7,38,40,41 60 – 450 29 Low & High Side RFIN_A RF VCO RFIN_B Bias Control Decode Logic IFOUT_A+ IFOUT_A- IFOUT_B+ IFOUT_B- GAIN_A[0:5] GAIN_B[0:5] TDD (STBY) LC_Mode Iset

Sampling IF Receiver 1710MHz to 2050MHz FlatNoise TM , Zero-Distortion TM , SIF Rx 2 Rev2, January 2014 IDTF0552NLGI Datasheet F0552NBGI Advance Datasheet TABLE OF CONTENTS

Sampling IF Receiver 1710MHz to 2050MHz FlatNoise TM , Zero-Distortion TM , SIF Rx 3 Rev2, January 2014 IDTF0552NLGI Datasheet F0552NBGI

Sampling IF Receiver 1710MHz to 2050MHz FlatNoise TM , Zero-Distortion TM , SIF Rx 4 Rev2, January 2014 IDTF0552NLGI Datasheet F0552NBGI Advance Datasheet ABSOLUTE MAXIMUM RATINGS VCC to GND -0.3V to +5.5V A[5:0], B[5:0], TDD_A, TDD_B (STBY), LCMode -0.3V to (VCC + 0.25V) MX_IFA+, MX_IFA-, MX_IFB+, MX_IFB- -0.3V to (VCC + 0.25V) IFOUT_A+, IFOUT_A-, IFOUT_B+, IFOUT_B- 1V to (Vcc + 0.3V) LO1_ADJ +1V to +3V LO2_ADJ +2.1V to +4V MX_IF_BiasA, MX_IF_BiasB -0.3V to +0.3V LO_IN, RFIN_A, RFIN_B -0.3V to +0.3V RF Input Power (RFIN_A, RFIN_B) +20dBm ISET_A, ISET_B to GND -0.3V to +2.2V Continuous Power Dissipation 2.5W θJA (Junction – Ambient) +25°C/W θJC (Junction – Case) The Case is defined as the exposed paddle +3°C/W Operating Temperature Range (Case Temperature) TC = -40°C to +105°C Maximum Junction Temperature 150°C Storage Temperature Range -65°C to +150°C Lead Temperature (soldering, 10s) +260°C Stresses above those listed above may cause permanent damage to the device. Functional operation of the device at these or any other conditions above those indicated in the operational section of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability.

Sampling IF Receiver 1710MHz to 2050MHz FlatNoiseTM, Zero-DistortionTM, SIF Rx 5 Rev2, January 2014 IDTF0552NLGI Datasheet F0552NBGI Advance Datasheet TRUTH TABLE – CHANNEL A & B Gain Set Target Gain CodeWord Code Name Gain Set Target Gain CodeWord Code Name Gain Set Target Gain CodeWord Code Name 27 000000 G27 5 010110 G5 -17 101100 G-17 26 000001 G26 4 010111 G4 -18 101101 G-18 25 000010 G25 3 011000 G3 -19 101110 G-19 24 000011 G24 2 011001 G2 -20 101111 G-20 23 000100 G23 1 011010 G1 -20 110000 G-20 22 000101 G22 0 011011 G0 -20 110001 G-20 21 000110 G21 -1 011100 G-1 -20 110010 G-20 20 000111 G20 -2 011101 G-2 -20 110011 G-20 19 001000 G19 -3 011110 G-3 -20 110100 G-20 18 001001 G18 -4 011111 G-4 -20 110101 G-20 17 001010 G17 -5 100000 G-5 -20 110110 G-20 16 001011 G16 -6 100001 G-6 -20 110111 G-20 15 001100 G15 -7 100010 G-7 -20 111000 G-20 14 001101 G14 -8 100011 G-8 -20 111001 G-20 13 001110 G13 -9 100100 G-9 -20 111010 G-20 12 001111 G12 -10 100101 G-10 -20 111011 G-20 11 010000 G11 -11 100110 G-11 -20 111100 G-20 10 010001 G10 -12 100111 G-12 -20 111101 G-20 9 010010 G9 -13 101000 G-13 -20 111110 G-20 8 010011 G8 -14 101001 G-14 -20 111111 G-20 7 010100 G7 -15 101010 G-15 6 010101 G6 -16 101011 G-16

Sampling IF Receiver 1710MHz to 2050MHz FlatNoiseTM, Zero-DistortionTM, SIF Rx 6 Rev2, January 2014 IDTF0552NLGI Datasheet F0552NBGI Advance Datasheet IDTF0552 RECOMMENDED OPERATING CONDITIONS Parameter Comment Symbol min typ max Units Supply Voltage(s) All VCC pins VCC 4.75 5.25 V LO Power PLO -3 +3 dBm Operating Temperature Range Case Temperature TCASE -40 +105 degC RF Freq Range For Cellular Applications FRF 1710 2050 MHz LO Freq Range FLOLS 1345 2330 IF Range FIF 60 450

Sampling IF Receiver 1710MHz to 2050MHz FlatNoiseTM, Zero-DistortionTM, SIF Rx 7 Rev2, January 2014 IDTF0552NLGI Datasheet F0552NBGI Advance Datasheet IDTF0552 SPECIFICATION F0552 Typical Application Circuit, when operated as a Sampling IF Receiver, VCC = +5.00V, TC = +25°C, FRF = 1880 MHz, FIF = 184MHz, FLO = 1696MHz, PLO = 0 dBm, Output power = +3dBm per tone unless otherwise noted, TDD_A, TDD_B = LOW. EVkit IF transformer losses are de-embedded unless otherwise noted. Parameter Comment Symbol min typ max units Logic Input High For all control pins VIH 1.07 V Logic Input Low For all control pins VIL 0.68 V Logic Current For all control pins IIH, IIL -150 10 μA Supply Current Total VCC, STD Mode ISTD 450 510 mA Supply Current Total VCC, LC Mode ILC 375 420 mA Supply Current  Standby Mode  STBY = VIH  Total Both Channels ISTBY 21 28 mA Gain STD Mode Conversion Power Gain Minimum attenuation GSTDMAX 27 291 31 dB Gain LC Mode Conversion Power Gain Minimum attenuation GLC 26.5 28.5 30.5 dB Gain control range GRANGE 472 dB Gain STD mode min gain setting Maximum attenuation GSTDMIN -18 dB Step size GSTEP 1 dB Differential Gain Error Between any two adjacent 1dB steps DNL 0.1 0.2 dB Integral Gain Error Error vs. line (G27 Ref) INL 0.2 0.8 dB Phase Error Maximum phase change between GMAX and any state down to G-14 IPE 2.5 4 degree NF STD Mode Noise Figure (@ +25C) NFSTD 9.6 10.6 dB NF STD Mode 10dB reduced gain NFSTD_G-10 9.6 10.6 dB NF LC Mode Noise Figure (@ +25C) NFLC 9.3 10.3 dB NF LC Mode 10dB reduced gain NFLC_G-10 9.5 10.5 dB NF w/Blocker  +100 MHz offset blocker  PIN = +4dBm  28dB gain reduced NFBLK 19.7 21 dB

Sampling IF Receiver 1710MHz to 2050MHz FlatNoiseTM, Zero-DistortionTM, SIF Rx 8 Rev2, January 2014 IDTF0552NLGI Datasheet F0552NBGI Advance Datasheet IDTF0552 Specification (Continued) F0552 Typical Application Circuit, when operated as a Sampling IF Receiver, VCC = +5.00V, TC = +25°C, FRF = 1880 MHz, FIF = 184MHz, FLO = 1696MHz, PLO = 0 dBm, Output power = +3dBm per tone unless otherwise noted, TDD_A, TDD_B = LOW. EVkit IF transformer losses are de-embedded unless otherwise noted. Parameter Comment Symbol min typ max units Turn-on time  Gate STBY from VIH to VIL  Time for IF Signal to settle to within 0.1 dB of final value TSETTL 0.17 0.20 sec Attenuator adjustment settling time  Any two Adjacent 1dB Steps  +/-0.10 dB Pout settling T1dB 17.5 25 nsec Output IP3 Max Gain, STDMODE  Set GMAX,  800 KHz Tone Separation IP3O1 40 45 dBm Output IP3 10dB reduced gain, STDMODE  From GMAX to GMAX-10,  Pout = +1dBm per tone  800 KHz Tone Separation IP3O2 40 45 dBm Output IP3 10dB reduced gain, STDMODE  From GMAX to GMAX-10,  Pout = +1dBm per tone  800 KHz Tone Separation  -40C ≤ Tcase ≤ +105C  IF = 138MHz, LO = 1742MHz  IF = 184MHz, LO = 1696MHz  IF = 276MHz3, LO = 1604MHz IP3O3 44 dBm Output IP3 Max Gain, LCMODE  Set GMAX,  800 KHz Tone Separation IP3O4 40 45 dBm Input IP3 22dB reduced gain, STDMODE  Set GMAX-22dB,  Pin = - 5dBm per tone  800 KHz Tone Separation IP3ISTD 28 31.5 dBm Input IP3 22dB reduced gain, LCMODE  Set GMAX-22dB,  Pin = -10dBm per tone  800 KHz Tone Separation IP3ILC 24.5 dBm 1 dB Compression Max Gain, STDMODE Output referred P1dBO1 17 19.8 dBm 1 dB Compression 30dB reduced gain, STDMODE  Input referred  Set GMAX-30dB P1dBI1 8.2 9.2 dBm 1 dB Compression Max Gain, LCMODE Output referred P1dBO2 17 19.8 dBm 1 dB Compression 30dB reduced gain, LCMODE  Input referred  Set GMAX-30dB P1dBI2 6.5 7 dBm 2RF – 2LO rejection Max Gain, STDMODE  Frequency = FRF - ½ FIF  PRF = -27dBm 2x21 -75 -65 dBc 2RF – 2LO rejection 22dB reduced gain, STDMODE  Frequency = FRF - ½ FIF  PRF = -5dBm 2x22 -72 -62 dBc

Sampling IF Receiver 1710MHz to 2050MHz FlatNoiseTM, Zero-DistortionTM, SIF Rx 9 Rev2, January 2014 IDTF0552NLGI Datasheet F0552NBGI Advance Datasheet IDTF0552 Specification (Continued) F0552 Typical Application Circuit, when operated as a Sampling IF Receiver, VCC = +5.00V, TC = +25°C, FRF = 1880 MHz, FIF = 184MHz, FLO = 1696MHz, PLO = 0 dBm, Output power = +3dBm per tone unless otherwise noted, TDD_A, TDD_B = LOW. EVkit IF transformer losses are de-embedded unless otherwise noted. Specification Notes: 1 – Items in min/max columns in bold italics are Guaranteed by Test using BOM1 components supporting 4:1 output impedance transformation to 50 ohms 2 – All other Items in min/max columns are Guaranteed by Design Characterization using BOM2 components supporting 2:1 output impedance transformation to 100 ohms 3 – Matching network changed for 276MHz IF per BOM table values Parameter Comment Symbol min typ max units 2RF – 2LO rejection Max Gain, LCMODE  Frequency = FRF - ½ FIF  PRF = -27dBm 2x23 -74 -60 dBc 2RF – 2LO rejection 22dB reduced gain, LCMODE  Frequency = FRF - ½ FIF  PRF = -5dBm 2x24 -71 -60 dBc 2nd Harmonic Max Gain, STDMODE PRF = -27 dBm HD21 -77 -70 dBc 2nd Harmonic Max Gain, LCMODE PRF = -27 dBm HD23 -76 -70 dBc 3rd Harmonic – Max Gain, STDMODE PRF = -27 dBm HD31 -100 -80 dBc 3rd Harmonic Max Gain, LCMODE PRF = -27 dBm HD33 -100 -82 dBc Channel Isolation Max Gain, STDMODE IF_B Pout vs. IF_A w/ RF_A input ISOC_STD 40 43 dB Channel Isolation Max Gain, LCMODE IF_B Pout vs. IF_A w/ RF_A input ISOC_LC 40 43 dB LO to IF leakage Max Gain, STDMODE ISOLI-1 -53 -45 dBm LO to IF leakage Max Gain, LCMODE ISOLI-3 -54 -45 dBm RF to IF leakage Max Gain, STDMODE PRF = -27 dBm ISORI-1 -84 -75 dBc RF to IF leakage Max Gain, LCMODE PRF = -27 dBm ISORI-2 -85 -75 dBc LO to RF leakage, STDMODE ISOLR -37 dBm RFIN Impedance Single Ended ZRFIN 50 Ω LO Port Impedance Single Ended ZLO 50 IF Output Impedance Differential ZIF 200

Sampling IF Receiver 1710MHz to 2050MHz FlatNoiseTM, Zero-DistortionTM, SIF Rx 10 Rev2, January 2014 IDTF0552NLGI Datasheet F0552NBGI Advance Datasheet TYPICAL OPERATING CONDITIONS (STD MODE, 184MHZ IF) Unless otherwise noted, the following conditions apply to the 184MHz Typ Ops Graphs:  BOM2 Applications circuit with 184 MHz IF Center +/- 40 MHz bandwidth network to provide matching to 100 ohm differential load provided by 2:1 transformer (see page 51)  Pout ~ +1 dBm  PIN from -27 to -6 dBm (Gain Setting Adjusted to yield Pout ~ +1 dBm without exceeding -6 dBm PIN)  Tone Spacing = 800 KHz  Device configured in Standard Mode with Low Side Injection  TCASE = 25C, VCC = 5.00 V, LO Power = 0 dBm  RF Frequency: 1.88 GHz  IF Frequency: 184 MHz  Gain Setting Sweep points: 27 dB (GMAX)  Transformer Losses are de-embedded  Input RF trace Losses are not de-embedded  Listed Temperatures are Case Temperature (TC = Case Temperature)  Where noted, TA or TAMB = Ambient Temperature

Sampling IF Receiver 1710MHz to 2050MHz FlatNoiseTM, Zero-DistortionTM, SIF Rx 11 Rev2, January 2014 IDTF0552NLGI Datasheet F0552NBGI Advance Datasheet TOCS [MAX GAIN, STD MODE, IF = 184M] GAIN (-1-) Gain vs. TCASE [low side inj.] Gain vs. VCC [low side inj.] Gain vs. LO level [low side inj.] Gain vs. TCASE [high side inj.] Gain vs. VCC [high side inj.] Gain vs. LO level [high side inj.] 144M 184M 224M 144M 184M 224M 144M 184M 224M 144M 184M 224M 1.71 GHz 1.85 GHz 1.93 GHz 2.03 GHz -40degC - 5.00V - 0dBm - ChA -40degC - 5.00V - 0dBm - ChB 25degC - 5.00V - 0dBm - ChA 25degC - 5.00V - 0dBm - ChB 105degC - 5.00V - 0dBm - ChA 105degC - 5.00V - 0dBm - ChB Gain (dB) RF Freq / IF Freq 144M 184M 224M 144M 184M 224M 144M 184M 224M 144M 184M 224M 1.71 GHz 1.85 GHz 1.93 GHz 2.03 GHz 25degC - 5.25V - 0dBm - ChA 25degC - 5.25V - 0dBm - ChB 25degC - 5.00V - 0dBm - ChA 25degC - 5.00V - 0dBm - ChB 25degC - 4.75V - 0dBm - ChA 25degC - 4.75V - 0dBm - ChB Gain (dB) RF Freq / IF Freq Gain (dB) RF Freq / IF Freq 144M 184M 224M 144M 184M 224M 144M 184M 224M 144M 184M 224M 1.71 GHz 1.85 GHz 1.93 GHz 2.03 GHz 25degC - 5.00V - 3dBm - ChA 25degC - 5.00V - 3dBm - ChB 25degC - 5.00V - 0dBm - ChA 25degC - 5.00V - 0dBm - ChB 25degC - 5.00V - -3dBm - ChA 25degC - 5.00V - -3dBm - ChB Gain (dB) RF Freq / IF Freq 144M 184M 224M 144M 184M 224M 144M 184M 224M 144M 184M 224M 1.71 GHz 1.85 GHz 1.93 GHz 2.03 GHz -40degC - 5.00V - 0dBm - ChA -40degC - 5.00V - 0dBm - ChB 25degC - 5.00V - 0dBm - ChA 25degC - 5.00V - 0dBm - ChB 105degC - 5.00V - 0dBm - ChA 105degC - 5.00V - 0dBm - ChB Gain (dB) RF Freq / IF Freq 144M 184M 224M 144M 184M 224M 144M 184M 224M 144M 184M 224M 1.71 GHz 1.85 GHz 1.93 GHz 2.03 GHz 25degC - 5.25V - 0dBm - ChA 25degC - 5.25V - 0dBm - ChB 25degC - 5.00V - 0dBm - ChA 25degC - 5.00V - 0dBm - ChB 25degC - 4.75V - 0dBm - ChA 25degC - 4.75V - 0dBm - ChB Gain (dB) RF Freq / IF Freq Gain (dB) RF Freq / IF Freq 144M 184M 224M 144M 184M 224M 144M 184M 224M 144M 184M 224M 1.71 GHz 1.85 GHz 1.93 GHz 2.03 GHz 25degC - 5.00V - 3dBm - ChA 25degC - 5.00V - 3dBm - ChB 25degC - 5.00V - 0dBm - ChA 25degC - 5.00V - 0dBm - ChB 25degC - 5.00V - -3dBm - ChA 25degC - 5.00V - -3dBm - ChB Gain (dB) RF Freq / IF Freq

Sampling IF Receiver 1710MHz to 2050MHz FlatNoiseTM, Zero-DistortionTM, SIF Rx 12 Rev2, January 2014 IDTF0552NLGI Datasheet F0552NBGI Advance Datasheet TOCS [MAX GAIN, STD MODE, IF = 184M] OIP3 (-2-) Output IP3 vs. TCASE [low side inj.] Output IP3 vs. VCC [low side inj.] Output IP3 vs. LO level [low side inj.] Output IP3 vs. TCASE [high side inj.] Output IP3 vs. VCC [high side inj.] Output IP3 vs. LO level [high side inj.] 144M 184M 224M 144M 184M 224M 144M 184M 224M 144M 184M 224M 1.71 GHz 1.85 GHz 1.93 GHz 2.03 GHz -40degC - 5.00V - 0dBm - ChA -40degC - 5.00V - 0dBm - ChB 25degC - 5.00V - 0dBm - ChA 25degC - 5.00V - 0dBm - ChB 105degC - 5.00V - 0dBm - ChA 105degC - 5.00V - 0dBm - ChB Output IP3 (dBm) RF Freq / IF Freq 144M 184M 224M 144M 184M 224M 144M 184M 224M 144M 184M 224M 1.71 GHz 1.85 GHz 1.93 GHz 2.03 GHz 25degC - 5.25V - 0dBm - ChA 25degC - 5.25V - 0dBm - ChB 25degC - 5.00V - 0dBm - ChA 25degC - 5.00V - 0dBm - ChB 25degC - 4.75V - 0dBm - ChA 25degC - 4.75V - 0dBm - ChB Output IP3 (dBm) RF Freq / IF Freq 144M 184M 224M 144M 184M 224M 144M 184M 224M 144M 184M 224M 1.71 GHz 1.85 GHz 1.93 GHz 2.03 GHz 25degC - 5.00V - 3dBm - ChA 25degC - 5.00V - 3dBm - ChB 25degC - 5.00V - 0dBm - ChA 25degC - 5.00V - 0dBm - ChB 25degC - 5.00V - -3dBm - ChA 25degC - 5.00V - -3dBm - ChB Output IP3 (dBm) RF Freq / IF Freq 144M 184M 224M 144M 184M 224M 144M 184M 224M 144M 184M 224M 1.71 GHz 1.85 GHz 1.93 GHz 2.03 GHz -40degC - 5.00V - 0dBm - ChA -40degC - 5.00V - 0dBm - ChB 25degC - 5.00V - 0dBm - ChA 25degC - 5.00V - 0dBm - ChB 105degC - 5.00V - 0dBm - ChA 105degC - 5.00V - 0dBm - ChB Output IP3 (dBm) RF Freq / IF Freq 144M 184M 224M 144M 184M 224M 144M 184M 224M 144M 184M 224M 1.71 GHz 1.85 GHz 1.93 GHz 2.03 GHz 25degC - 5.25V - 0dBm - ChA 25degC - 5.25V - 0dBm - ChB 25degC - 5.00V - 0dBm - ChA 25degC - 5.00V - 0dBm - ChB 25degC - 4.75V - 0dBm - ChA 25degC - 4.75V - 0dBm - ChB Output IP3 (dBm) RF Freq / IF Freq 144M 184M 224M 144M 184M 224M 144M 184M 224M 144M 184M 224M 1.71 GHz 1.85 GHz 1.93 GHz 2.03 GHz 25degC - 5.00V - 3dBm - ChA 25degC - 5.00V - 3dBm - ChB 25degC - 5.00V - 0dBm - ChA 25degC - 5.00V - 0dBm - ChB 25degC - 5.00V - -3dBm - ChA 25degC - 5.00V - -3dBm - ChB Output IP3 (dBm) RF Freq / IF Freq

Sampling IF Receiver 1710MHz to 2050MHz FlatNoiseTM, Zero-DistortionTM, SIF Rx 13 Rev2, January 2014 IDTF0552NLGI Datasheet F0552NBGI Advance Datasheet TOCS [MAX GAIN, STD MODE, IF = 184M] OIP2 (-3-) Output IP2 vs. TCASE [low side inj.] Output IP2 vs. VCC [low side inj.] Output IP2 vs. LO level [low side inj.] Output IP2 vs. TCASE [high side inj.] Output IP2 vs. VCC [high side inj.] Output IP2 vs. LO level [high side inj.] 100 144M 184M 224M 144M 184M 224M 144M 184M 224M 144M 184M 224M 1.71 GHz 1.85 GHz 1.93 GHz 2.03 GHz -40degC - 5.00V - 0dBm - ChA -40degC - 5.00V - 0dBm - ChB 25degC - 5.00V - 0dBm - ChA 25degC - 5.00V - 0dBm - ChB 105degC - 5.00V - 0dBm - ChA 105degC - 5.00V - 0dBm - ChB Output IP2 (dBm) RF Freq / IF Freq 100 144M 184M 224M 144M 184M 224M 144M 184M 224M 144M 184M 224M 1.71 GHz 1.85 GHz 1.93 GHz 2.03 GHz 25degC - 5.25V - 0dBm - ChA 25degC - 5.25V - 0dBm - ChB 25degC - 5.00V - 0dBm - ChA 25degC - 5.00V - 0dBm - ChB 25degC - 4.75V - 0dBm - ChA 25degC - 4.75V - 0dBm - ChB Output IP2 (dBm) RF Freq / IF Freq 100 144M 184M 224M 144M 184M 224M 144M 184M 224M 144M 184M 224M 1.71 GHz 1.85 GHz 1.93 GHz 2.03 GHz 25degC - 5.00V - 3dBm - ChA 25degC - 5.00V - 3dBm - ChB 25degC - 5.00V - 0dBm - ChA 25degC - 5.00V - 0dBm - ChB 25degC - 5.00V - -3dBm - ChA 25degC - 5.00V - -3dBm - ChB Output IP2 (dBm) RF Freq / IF Freq 100 144M 184M 224M 144M 184M 224M 144M 184M 224M 144M 184M 224M 1.71 GHz 1.85 GHz 1.93 GHz 2.03 GHz -40degC - 5.00V - 0dBm - ChA -40degC - 5.00V - 0dBm - ChB 25degC - 5.00V - 0dBm - ChA 25degC - 5.00V - 0dBm - ChB 105degC - 5.00V - 0dBm - ChA 105degC - 5.00V - 0dBm - ChB Output IP2 (dBm) RF Freq / IF Freq 100 144M 184M 224M 144M 184M 224M 144M 184M 224M 144M 184M 224M 1.71 GHz 1.85 GHz 1.93 GHz 2.03 GHz 25degC - 5.25V - 0dBm - ChA 25degC - 5.25V - 0dBm - ChB 25degC - 5.00V - 0dBm - ChA 25degC - 5.00V - 0dBm - ChB 25degC - 4.75V - 0dBm - ChA 25degC - 4.75V - 0dBm - ChB Output IP2 (dBm) RF Freq / IF Freq 100 144M 184M 224M 144M 184M 224M 144M 184M 224M 144M 184M 224M 1.71 GHz 1.85 GHz 1.93 GHz 2.03 GHz 25degC - 5.00V - 3dBm - ChA 25degC - 5.00V - 3dBm - ChB 25degC - 5.00V - 0dBm - ChA 25degC - 5.00V - 0dBm - ChB 25degC - 5.00V - -3dBm - ChA 25degC - 5.00V - -3dBm - ChB Output IP2 (dBm) RF Freq / IF Freq

Sampling IF Receiver 1710MHz to 2050MHz FlatNoiseTM, Zero-DistortionTM, SIF Rx 14 Rev2, January 2014 IDTF0552NLGI Datasheet F0552NBGI Advance Datasheet TOCS [MAX GAIN, STD MODE, IF = 184M] 2X2 (-4-) 2x2 Rejection vs. TCASE [low side inj.] 2x2 Rejection vs. VCC [low side inj.] 2x2 Rejection vs. LO level [low side inj.] 2x2 Rejection vs. TCASE [high side inj.] 2x2 Rejection vs. VCC [high side inj.] 2x2 Rejection vs. LO level [high side inj.] -100 -90 -80 -70 -60 -50 -40 -30 -20 144M 184M 224M 144M 184M 224M 144M 184M 224M 144M 184M 224M 1.71 GHz 1.85 GHz 1.93 GHz 2.03 GHz -40degC - 5.00V - 0dBm - ChA -40degC - 5.00V - 0dBm - ChB 25degC - 5.00V - 0dBm - ChA 25degC - 5.00V - 0dBm - ChB 105degC - 5.00V - 0dBm - ChA 105degC - 5.00V - 0dBm - ChB 2X2 Rejection (dBc) RF Freq / IF Freq -100 -90 -80 -70 -60 -50 -40 -30 -20 144M 184M 224M 144M 184M 224M 144M 184M 224M 144M 184M 224M 1.71 GHz 1.85 GHz 1.93 GHz 2.03 GHz 25degC - 5.25V - 0dBm - ChA 25degC - 5.25V - 0dBm - ChB 25degC - 5.00V - 0dBm - ChA 25degC - 5.00V - 0dBm - ChB 25degC - 4.75V - 0dBm - ChA 25degC - 4.75V - 0dBm - ChB 2X2 Rejection (dBc) RF Freq / IF Freq -100 -90 -80 -70 -60 -50 -40 -30 -20 144M 184M 224M 144M 184M 224M 144M 184M 224M 144M 184M 224M 1.71 GHz 1.85 GHz 1.93 GHz 2.03 GHz 25degC - 5.00V - 3dBm - ChA 25degC - 5.00V - 3dBm - ChB 25degC - 5.00V - 0dBm - ChA 25degC - 5.00V - 0dBm - ChB 25degC - 5.00V - -3dBm - ChA 25degC - 5.00V - -3dBm - ChB 2X2 Rejection (dBc) RF Freq / IF Freq -100 -90 -80 -70 -60 -50 -40 -30 -20 144M 184M 224M 144M 184M 224M 144M 184M 224M 144M 184M 224M 1.71 GHz 1.85 GHz 1.93 GHz 2.03 GHz -40degC - 5.00V - 0dBm - ChA -40degC - 5.00V - 0dBm - ChB 25degC - 5.00V - 0dBm - ChA 25degC - 5.00V - 0dBm - ChB 105degC - 5.00V - 0dBm - ChA 105degC - 5.00V - 0dBm - ChB 2X2 Rejection (dBc) RF Freq / IF Freq -100 -90 -80 -70 -60 -50 -40 -30 -20 144M 184M 224M 144M 184M 224M 144M 184M 224M 144M 184M 224M 1.71 GHz 1.85 GHz 1.93 GHz 2.03 GHz 25degC - 5.25V - 0dBm - ChA 25degC - 5.25V - 0dBm - ChB 25degC - 5.00V - 0dBm - ChA 25degC - 5.00V - 0dBm - ChB 25degC - 4.75V - 0dBm - ChA 25degC - 4.75V - 0dBm - ChB 2X2 Rejection (dBc) RF Freq / IF Freq -100 -90 -80 -70 -60 -50 -40 -30 -20 144M 184M 224M 144M 184M 224M 144M 184M 224M 144M 184M 224M 1.71 GHz 1.85 GHz 1.93 GHz 2.03 GHz 25degC - 5.00V - 3dBm - ChA 25degC - 5.00V - 3dBm - ChB 25degC - 5.00V - 0dBm - ChA 25degC - 5.00V - 0dBm - ChB 25degC - 5.00V - -3dBm - ChA 25degC - 5.00V - -3dBm - ChB 2X2 Rejection (dBc) RF Freq / IF Freq

Sampling IF Receiver 1710MHz to 2050MHz FlatNoiseTM, Zero-DistortionTM, SIF Rx 15 Rev2, January 2014 IDTF0552NLGI Datasheet F0552NBGI Advance Datasheet TOCS [MAX GAIN, STD MODE, IF = 184M] LEAKAGE (-5-) LO to IF Leakage vs. TCASE [low side inj.] LO to IF Leakage vs. VCC [low side inj.] LO to IF Leakage vs. LO level [low side inj.] LO to IF Leakage vs. TCASE [high side inj.] LO to IF Leakage vs. VCC [high side inj.] LO to IF Leakage vs. LO level [high side inj.] -65 -60 -55 -50 -45 -40 -35 -30 -25 144M 184M 224M 144M 184M 224M 144M 184M 224M 144M 184M 224M 1.71 GHz 1.85 GHz 1.93 GHz 2.03 GHz -40degC - 5.00V - 0dBm - ChA -40degC - 5.00V - 0dBm - ChB 25degC - 5.00V - 0dBm - ChA 25degC - 5.00V - 0dBm - ChB 105degC - 5.00V - 0dBm - ChA 105degC - 5.00V - 0dBm - ChB LO to IF Leakage (dBm) RF Freq / IF Freq -65 -60 -55 -50 -45 -40 -35 -30 -25 144M 184M 224M 144M 184M 224M 144M 184M 224M 144M 184M 224M 1.71 GHz 1.85 GHz 1.93 GHz 2.03 GHz 25degC - 5.25V - 0dBm - ChA 25degC - 5.25V - 0dBm - ChB 25degC - 5.00V - 0dBm - ChA 25degC - 5.00V - 0dBm - ChB 25degC - 4.75V - 0dBm - ChA 25degC - 4.75V - 0dBm - ChB LO to IF Leakage (dBm) RF Freq / IF Freq -65 -60 -55 -50 -45 -40 -35 -30 -25 144M 184M 224M 144M 184M 224M 144M 184M 224M 144M 184M 224M 1.71 GHz 1.85 GHz 1.93 GHz 2.03 GHz 25degC - 5.00V - 3dBm - ChA 25degC - 5.00V - 3dBm - ChB 25degC - 5.00V - 0dBm - ChA 25degC - 5.00V - 0dBm - ChB 25degC - 5.00V - -3dBm - ChA 25degC - 5.00V - -3dBm - ChB LO to IF Leakage (dBm) RF Freq / IF Freq -65 -60 -55 -50 -45 -40 -35 -30 -25 144M 184M 224M 144M 184M 224M 144M 184M 224M 144M 184M 224M 1.71 GHz 1.85 GHz 1.93 GHz 2.03 GHz -40degC - 5.00V - 0dBm - ChA -40degC - 5.00V - 0dBm - ChB 25degC - 5.00V - 0dBm - ChA 25degC - 5.00V - 0dBm - ChB 105degC - 5.00V - 0dBm - ChA 105degC - 5.00V - 0dBm - ChB LO to IF Leakage (dBm) RF Freq / IF Freq -65 -60 -55 -50 -45 -40 -35 -30 -25 144M 184M 224M 144M 184M 224M 144M 184M 224M 144M 184M 224M 1.71 GHz 1.85 GHz 1.93 GHz 2.03 GHz 25degC - 5.25V - 0dBm - ChA 25degC - 5.25V - 0dBm - ChB 25degC - 5.00V - 0dBm - ChA 25degC - 5.00V - 0dBm - ChB 25degC - 4.75V - 0dBm - ChA 25degC - 4.75V - 0dBm - ChB LO to IF Leakage (dBm) RF Freq / IF Freq -65 -60 -55 -50 -45 -40 -35 -30 -25 144M 184M 224M 144M 184M 224M 144M 184M 224M 144M 184M 224M 1.71 GHz 1.85 GHz 1.93 GHz 2.03 GHz 25degC - 5.00V - 3dBm - ChA 25degC - 5.00V - 3dBm - ChB 25degC - 5.00V - 0dBm - ChA 25degC - 5.00V - 0dBm - ChB 25degC - 5.00V - -3dBm - ChA 25degC - 5.00V - -3dBm - ChB LO to IF Leakage (dBm) RF Freq / IF Freq

Sampling IF Receiver 1710MHz to 2050MHz FlatNoiseTM, Zero-DistortionTM, SIF Rx 16 Rev2, January 2014 IDTF0552NLGI Datasheet F0552NBGI Advance Datasheet TOCS [MAX GAIN, STD MODE, IF = 184M] DC CURRENT (-6-) Total Current Drain vs. TCASE [low side inj.] Total Current Drain vs. VCC [low side inj.] Total Current Drain vs. LO level [low side inj.] Total Current Drain vs. TCASE [high side inj.] Total Current Drain vs. VCC [high side inj.] Total Current Drain vs. LO level [high side inj.] 0.42 0.44 0.46 0.48 0.50 0.52 144M 184M 224M 144M 184M 224M 144M 184M 224M 144M 184M 224M 1.71 GHz 1.85 GHz 1.93 GHz 2.03 GHz -40degC - 5.00V - 0dBm 25degC - 5.00V - 0dBm 105degC - 5.00V - 0dBm RF Freq / IF Freq Total ICC (Amps) 0.42 0.44 0.46 0.48 0.50 0.52 144M 184M 224M 144M 184M 224M 144M 184M 224M 144M 184M 224M 1.71 GHz 1.85 GHz 1.93 GHz 2.03 GHz 25degC - 5.25V - 0dBm 25degC - 5.00V - 0dBm 25degC - 4.75V - 0dBm RF Freq / IF Freq Total ICC (Amps) 0.42 0.44 0.46 0.48 0.50 0.52 144M 184M 224M 144M 184M 224M 144M 184M 224M 144M 184M 224M 1.71 GHz 1.85 GHz 1.93 GHz 2.03 GHz 25degC - 5.00V - 3dBm 25degC - 5.00V - 0dBm 25degC - 5.00V - -3dBm RF Freq / IF Freq Total ICC (Amps) 0.42 0.44 0.46 0.48 0.50 0.52 144M 184M 224M 144M 184M 224M 144M 184M 224M 144M 184M 224M 1.71 GHz 1.85 GHz 1.93 GHz 2.03 GHz -40degC - 5.00V - 0dBm 25degC - 5.00V - 0dBm 105degC - 5.00V - 0dBm RF Freq / IF Freq Total ICC (Amps) 0.42 0.44 0.46 0.48 0.50 0.52 144M 184M 224M 144M 184M 224M 144M 184M 224M 144M 184M 224M 1.71 GHz 1.85 GHz 1.93 GHz 2.03 GHz 25degC - 5.25V - 0dBm 25degC - 5.00V - 0dBm 25degC - 4.75V - 0dBm RF Freq / IF Freq Total ICC (Amps) 0.42 0.44 0.46 0.48 0.50 0.52 144M 184M 224M 144M 184M 224M 144M 184M 224M 144M 184M 224M 1.71 GHz 1.85 GHz 1.93 GHz 2.03 GHz 25degC - 5.00V - 3dBm 25degC - 5.00V - 0dBm 25degC - 5.00V - -3dBm RF Freq / IF Freq Total ICC (Amps)

Sampling IF Receiver 1710MHz to 2050MHz FlatNoiseTM, Zero-DistortionTM, SIF Rx 17 Rev2, January 2014 IDTF0552NLGI Datasheet F0552NBGI Advance Datasheet TOCS SWEPT GAIN SETTING [STD MODE, IF =184M, LS INJECTION] GAIN, OIP3, IIP3 (-7-) Gain [1.71 GHz] Output IP3 [1.71 GHz] Input IP3 [1.71 GHz] Gain [1.88 GHz] Output IP3 [1.88 GHz] Input IP3 [1.88 GHz] -22 -18 -14 -10 -22-18-14-10-6-226101418222630 Gain (dB) Gain Setting (dB) -40degC ChA -40degC ChB 25degC ChA 25degC ChB 105degC ChA 105degC ChB -22-18-14-10-6-2261014182226 -40C / ChA -40C / ChB +25C / ChA +25C / ChB +105C / ChA +105C / ChB Gain Setting (dB) / ~PIN (dBm) Output IP3 (dBm) -22-18-14-10-6-2261014182226 -40C / ChA -40C / ChB +25C / ChA +25C / ChB +105C / ChA +105C / ChB Gain Setting (dB) / ~PIN (dBm per Tone) Input IP3 (dBm) -22 -18 -14 -10 -22-18-14-10-6-226101418222630 Gain (dB) Gain Setting (dB) -40degC ChA -40degC ChB 25degC ChA 25degC ChB 105degC ChA 105degC ChB -22-18-14-10-6-2261014182226 -40C / ChA -40C / ChB +25C / ChA +25C / ChB +105C / ChA +105C / ChB Gain Setting (dB) / ~PIN (dBm) Output IP3 (dBm) -22-18-14-10-6-2261014182226 -40C / ChA -40C / ChB +25C / ChA +25C / ChB +105C / ChA +105C / ChB Gain Setting (dB) / ~PIN (dBm per Tone) Input IP3 (dBm)

Sampling IF Receiver 1710MHz to 2050MHz FlatNoiseTM, Zero-DistortionTM, SIF Rx 18 Rev2, January 2014 IDTF0552NLGI Datasheet F0552NBGI Advance Datasheet TOCS SWEPT GAIN SETTING [STD MODE, IF =184M, LS INJECTION] OIP2, IIP2, 2X2 (-8-) Output IP2 [1.71 GHz] Input IP2 [1.71 GHz] 2x2 Rejection [1.71 GHz] Output IP2 [1.88 GHz] Input IP2 [1.88 GHz] 2x2 Rejection [1.88 GHz] -22-18-14-10-6-2261014182226 -40C / ChA -40C / ChB +25C / ChA +25C / ChB +105C / ChA +105C / ChB Gain Setting (dB) / ~PIN (dBm per Tone) Output IP2 (dBm) -22-18-14-10-6-2261014182226 -40C / ChA -40C / ChB +25C / ChA +25C / ChB +105C / ChA +105C / ChB Gain Setting (dB) / ~PIN (dBm per Tone) Input IP2 (dBm) -100 -90 -80 -70 -60 -50 -40 -30 -20 -22-18-14-10-6-2261014182226 -40C / ChA -40C / ChB +25C / ChA +25C / ChB +105C / ChA +105C / ChB Gain Setting (dB) / ~PIN (dBm per Tone) 2x2 Rejection (dBc) -22-18-14-10-6-2261014182226 -40C / ChA -40C / ChB +25C / ChA +25C / ChB +105C / ChA +105C / ChB Gain Setting (dB) / ~PIN (dBm per Tone) Output IP2 (dBm) -22-18-14-10-6-2261014182226 -40C / ChA -40C / ChB +25C / ChA +25C / ChB +105C / ChA +105C / ChB Gain Setting (dB) / ~PIN (dBm per Tone) Input IP2 (dBm) -100 -90 -80 -70 -60 -50 -40 -30 -20 -22-18-14-10-6-2261014182226 -40C / ChA -40C / ChB +25C / ChA +25C / ChB +105C / ChA +105C / ChB Gain Setting (dB) / ~PIN (dBm per Tone) 2x2 Rejection (dBc)

Sampling IF Receiver 1710MHz to 2050MHz FlatNoiseTM, Zero-DistortionTM, SIF Rx 19 Rev2, January 2014 IDTF0552NLGI Datasheet F0552NBGI Advance Datasheet TOCS SWEPT GAIN SETTING [STD MODE, IF =184M, LS INJECTION] 3X3, LEAKAGE (-9-) 3x3 Rejection [1.71 GHz] LO to IF Leakage [low side inj, 1.85 GHz] RF to IF Leakage [low side inj., 1.85 GHz] 3x3 Rejection [1.88 GHz] LO to IF Leakage [high side inj., 1.85 GHz] RF to IF Leakage [high side inj., 1.85 GHz] -100 -90 -80 -70 -60 -50 -40 -30 -20 -22-18-14-10-6-2261014182226 -40C / ChA -40C / ChB +25C / ChA +25C / ChB +105C / ChA +105C / ChB Gain Setting (dB) / ~PIN (dBm per Tone) 3x3 Rejection (dBc) -76 -72 -68 -64 -60 -56 -52 -48 -44 -40 -36 -32 -28 -24 -22-18-14-10-6-226101418222630 LO to IF Leakage (dBm) Gain Setting (dB) / PIN (dBm) -40degC ChA -40degC ChB 25degC ChA 25degC ChB 105degC ChA 105degC ChB -30 -26 -22 -18 -14 -10 -6 -2 0 0 0 0 0 0 -92 -88 -84 -80 -76 -72 -68 -64 -60 -56 -52 -48 -44 -40 -22-18-14-10-6-226101418222630 RF to IF Leakage (dBm) Gain Setting (dB) / PIN (dBm) -40degC ChA -40degC ChB 25degC ChA 25degC ChB 105degC ChA 105degC ChB -30 -26 -22 -18 -14 -10 -6 -2 0 0 0 0 0 0 -100 -90 -80 -70 -60 -50 -40 -30 -20 -22-18-14-10-6-2261014182226 -40C / ChA -40C / ChB +25C / ChA +25C / ChB +105C / ChA +105C / ChB Gain Setting (dB) / ~PIN (dBm per Tone) 3x3 Rejection (dBc) -76 -72 -68 -64 -60 -56 -52 -48 -44 -40 -36 -32 -28 -24 -22-18-14-10-6-226101418222630 LO to IF Leakage (dBm) Gain Setting (dB) / PIN (dBm) -40degC ChA -40degC ChB 25degC ChA 25degC ChB 105degC ChA 105degC ChB -30 -26 -22 -18 -14 -10 -6 -2 0 0 0 0 0 0 -92 -88 -84 -80 -76 -72 -68 -64 -60 -56 -52 -48 -44 -40 -22-18-14-10-6-226101418222630 RF to IF Leakage (dBm) Gain Setting (dB) / PIN (dBm) -40degC ChA -40degC ChB 25degC ChA 25degC ChB 105degC ChA 105degC ChB -30 -26 -22 -18 -14 -10 -6 -2 0 0 0 0 0 0

Sampling IF Receiver 1710MHz to 2050MHz FlatNoiseTM, Zero-DistortionTM, SIF Rx 20 Rev2, January 2014 IDTF0552NLGI Datasheet F0552NBGI Advance Datasheet TOCS NOISE FIGURE [STD MODE, CHA ONLY] (-10-) RF & IF Freq Sweep [GMAX, Low Side inj.] RF & IF Freq Sweep [GMAX, High Side inj.] Gain Setting Sweep [LO = 1.75 GHz, IF = 184 MHz] RF & IF Freq Sweep [G10dB, Low Side inj.] RF & IF Freq Sweep [G10dB, High Side inj.] Blocker Power Sweep [LO = 2.15 GHz, TA = 25C] 144M 184M 224M 144M 184M 224M 144M 184M 224M

1550 MHz 1750 MHz 1950 MHz

-40 degC 25 degC 105 degC LO Freq / IF Freq Noise Figure (dB) 144M 184M 224M 144M 184M 224M 144M 184M 224M

1750 MHz 1950 MHz 2150 MHz

-40 degC 25 degC 105 degC LO Freq / IF Freq Noise Figure (dB) 27 20 10 0 -10 -20 -40 degC 25 degC 105 degC Gain Setting (dB) Noise Figure (dB) 144M 184M 224M 144M 184M 224M 144M 184M 224M -40 degC 25 degC 105 degC LO Freq / IF Freq Noise Figure (dB) 144M 184M 224M 144M 184M 224M 144M 184M 224M -40 degC 25 degC 105 degC LO Freq / IF Freq Noise Figure (dB) -28 -24 -20 -16 -12 -8 -4 0 4 8 12 Noise Figure (dB) Input Blocker Power (dBm) Constant Pout / offset = 100 MHz Constant Pout / offset = 20 MHz Gain = Gmax / offset = 100 MHz Gain = Gmax / offset = 20 MHz

Sampling IF Receiver 1710MHz to 2050MHz FlatNoiseTM, Zero-DistortionTM, SIF Rx 21 Rev2, January 2014 IDTF0552NLGI Datasheet F0552NBGI Advance Datasheet TOCS SPURS [STD MODE, IF MATCH 184M, LO = 1.563 GHZ, GAIN = 0 dB, TA = 25C] (-11-) Close-In Spurs [ChA, PRF = -5 dBm] Close-In Spurs [ChA, PRF = 0 dBm] Other Spurs [ChA, PRF = -5 dBm] Close-In Spurs [ChB, PRF = -5 dBm] Close-In Spurs [ChB, PRF = 0 dBm] Other Spurs [ChB, PRF = -5 dBm] 7-9 -1 8 9 -2 -3 -4-5-6-7-8-9 98765 4 3 2 -8 1 -7 8 -6 7 -5 -68 1 -7 -8 2 3 4 56789 -9-8-7-6-5-4 -3 -2 9 -1 8 -9 7 -8 6 -1000.0 1000.0 3000.0 5000.0 7000.0 9000.0 11000.0 -120 -110 -100 -90 -80 -70 -60 -50 -40 -30 -20 -10 1350 1400 1450 1500 1550 1600 1650 1700 1750 1800 1850 Spur Rejection (dBc) Frequency (MHz) Spur (dBc) M x RF N x LO FundamentalImage 7-9 -1 8 9 -2 -3 -4-5-6-7-8-9 98765 4 3 2 -8 1 -7 8 -6 7 -5 -68 1 -7 -8 2 3 4 56789 -9-8-7-6-5-4 -3 -2 9 -1 8 -9 7 -8 6 -1000.0 1000.0 3000.0 5000.0 7000.0 9000.0 11000.0 -120 -110 -100 -90 -80 -70 -60 -50 -40 -30 -20 -10 1350 1400 1450 1500 1550 1600 1650 1700 1750 1800 1850 Spur Rejection (dBc) Frequency (MHz) Spur (dBc) M x RF N x LO FundamentalImage 6 -45 -74 -37-6 6 3-5 5 -2 -4-6 64 2 -5 5-3 3 -4 -54 5 -1 -2 -3-4 -7 5-6 9-5 4-98 -8 -47 -7 3 69 -9-6 -3 8 -85 -5 7 9-7 -9 2 4 68 -1000.0 1000.0 3000.0 5000.0 7000.0 9000.0 11000.0 -120 -110 -100 -90 -80 -70 -60 -50 -40 -30 -20 -10 1850 1950 2050 2150 2250 2350 2450 2550 2650 2750 2850 2950 3050 3150 Spur Rejection (dBc) Frequency (MHz) Spur (dBc) M x RF N x LO 7-9 -1 8 9 -2 -3 -4-5-6-7-8-9 98765 4 3 2 -8 1 -7 8 -6 7 -5 -68 1 -7 -8 2 3 4 56789 -9-8-7-6-5-4 -3 -2 9 -1 8 -9 7 -8 6 -1000.0 1000.0 3000.0 5000.0 7000.0 9000.0 11000.0 -120 -110 -100 -90 -80 -70 -60 -50 -40 -30 -20 -10 1350 1400 1450 1500 1550 1600 1650 1700 1750 1800 1850 Spur Rejection (dBc) Frequency (MHz) Spur (dBc) M x RF N x LO FundamentalImage 7-9 -1 8 9 -2 -3 -4-5-6-7-8-9 98765 4 3 2 -8 1 -7 8 -6 7 -5 -68 1 -7 -8 2 3 4 56789 -9-8-7-6-5-4 -3 -2 9 -1 8 -9 7 -8 6 -1000.0 1000.0 3000.0 5000.0 7000.0 9000.0 11000.0 -120 -110 -100 -90 -80 -70 -60 -50 -40 -30 -20 -10 1350 1400 1450 1500 1550 1600 1650 1700 1750 1800 1850 Spur Rejection (dBc) Frequency (MHz) Spur (dBc) M x RF N x LO FundamentalImage 6 -45 -74 -37-6 6 3-5 5 -2 -4-6 64 2 -5 5-3 3 -4 -54 5 -1 -2 -3-4 -7 5-6 9-5 4-98 -8 -47 -7 3 69 -9-6 -3 8 -85 -5 7 9-7 -9 2 4 68 -1000.0 1000.0 3000.0 5000.0 7000.0 9000.0 11000.0 -120 -110 -100 -90 -80 -70 -60 -50 -40 -30 -20 -10 1850 1950 2050 2150 2250 2350 2450 2550 2650 2750 2850 2950 3050 3150 Spur Rejection (dBc) Frequency (MHz) Spur (dBc) M x RF N x LO

Sampling IF Receiver 1710MHz to 2050MHz FlatNoiseTM, Zero-DistortionTM, SIF Rx 22 Rev2, January 2014 IDTF0552NLGI Datasheet F0552NBGI Advance Datasheet GAIN ACCURACY, BOARD LOSSES (-12-) Accuracy vs. TCASE [RF = 1.85 GHz, IF = 184 MHz] Transformer TC2-7T Loss vs. Temperature Accuracy vs. IF Freq [RF = 1.85 GHz, TCASE = 25C] -1.25 -1.00 -0.75 -0.50 -0.25 0.00 0.25 0.50 0.75 1.00 1.25 27 23 19 15 11 7 3 -1 -5 -9 -13 -17 105 degC - Channel A 105 degC - Channel B 25 degC - Channel A 25 degC - Channel B -40 degC - Channel A -40 degC - Channel B Gain Setting (dB) Absolute Gain Error (dB) 0.00 0.25 0.50 0.75 1.00 1.25 1.50 -40 25 100 IF Frequency (GHz) TC2 Loss (dB) -1.25 -1.00 -0.75 -0.50 -0.25 0.00 0.25 0.50 0.75 1.00 1.25 27 23 19 15 11 7 3 -1 -5 -9 -13 -17

144 MHz - Channel A 144 MHz - Channel B

184 MHz - Channel A 184 MHz - Channel B

224 MHz - Channel A 224 MHz - Channel B

Gain Setting (dB) Absolute Gain Error (dB)

Sampling IF Receiver 1710MHz to 2050MHz FlatNoiseTM, Zero-DistortionTM, SIF Rx 23 Rev2, January 2014 IDTF0552NLGI Datasheet F0552NBGI Advance Datasheet TOCS P1dB [STD MODE] (-13-) P1dB RF Sweep [IF = 184 MHz, Low Side inj.] P1dB Gain Set Sweep [RF = 1.88 GHz IF = 184 MHz] P1dB RF Sweep [IF = 184 MHz, High Side inj.] 1.7 1.85 1.93 2.03 27dB Gain Set - Channel A 27dB Gain Set - Channel B 17dB Gain Set - Channel A 17dB Gain Set - Channel B 7dB Gain Set - Channel A 7dB Gain Set - Channel B RF Freq (GHz) Output P1dB (dBm) -10 27 23 19 15 11 7 3 -1 -5 -9 -13 -17 -40 28 105 Gain Setting (dB) Input P1dB (dBm) Case Temperature 1.7 1.85 1.93 2.03 27dB Gain Set - Channel A 27dB Gain Set - Channel B 17dB Gain Set - Channel A 17dB Gain Set - Channel B 7dB Gain Set - Channel A 7dB Gain Set - Channel B RF Freq (GHz) Output P1dB (dBm)

Sampling IF Receiver 1710MHz to 2050MHz FlatNoiseTM, Zero-DistortionTM, SIF Rx 24 Rev2, January 2014 IDTF0552NLGI Datasheet F0552NBGI Advance Datasheet TYPICAL OPERATING CONDITIONS (STD MODE, 138MHZ IF) Unless otherwise noted, the following conditions apply to the 138MHz Typ Ops Graphs:  BOM2 Applications circuit with 138 MHz IF Center +/- 40 MHz bandwidth network to provide matching to 100 ohm differential load provided by 2:1 transformer (see page 51)  Pout ~ +1 dBm  PIN from -27 to -6 dBm (Gain Setting Adjusted to yield Pout ~ +1 dBm without exceeding -6 dBm PIN)  Tone Spacing = 800 KHz  Device configured in Standard Mode with Low Side Injection  TCASE = 25C, VCC = 5.00 V, LO Power = 0 dBm  RF Frequency: 1.88 GHz  IF Frequency: 138 MHz  Transformer Losses are de-embedded  Input RF trace Losses are not de-embedded

Sampling IF Receiver 1710MHz to 2050MHz FlatNoiseTM, Zero-DistortionTM, SIF Rx 25 Rev2, January 2014 IDTF0552NLGI Datasheet F0552NBGI Advance Datasheet TOCS [STD MODE, IF = 138M, LS INJECTION] GAIN, OIP3, OIP2 (-14-) Gain vs. TCASE [1.71 GHz RF] Output IP3 vs. TCASE [1.71 GHz RF] Output IP2 vs. TCASE [1.71 GHz RF] Gain vs. TCASE [1.88 GHz RF] Output IP3 vs. TCASE [1.88 GHz RF] Output IP2 vs. TCASE [1.88 GHz RF] 27 25 23 21 19 17 27 25 23 21 19 17 27 25 23 21 19 17 98MHz - 138MHz - 178MHz Gain (dB) IF Frequency / Gain Setting (dB) or -Pin (dBm) -40degC / 1.71GHz -40degC / 1.88GHz 25degC / 1.71GHz 25degC / 1.88GHz 105degC / 1.71GHz 105degC / 1.88GHz 27 25 23 21 19 17 27 25 23 21 19 17 27 25 23 21 19 17 98MHz - 138MHz - 178MHz Output IP3 (dBm) IF Frequency / Gain Setting (dB) or -Pin (dBm) -40degC / Channel A -40degC / Channel B 25degC / Channel A 25degC / Channel B 105degC / Channel A 105degC / Channel B 100 27 25 23 21 19 17 27 25 23 21 19 17 27 25 23 21 19 17 98MHz - 138MHz - 178MHz Output IP2 (dBm) IF Frequency / Gain Setting (dB) or -Pin (dBm) -40degC / Channel A -40degC / Channel B 25degC / Channel A 25degC / Channel B 105degC / Channel A 105degC / Channel B 27 25 23 21 19 17 27 25 23 21 19 17 27 25 23 21 19 17 98MHz - 138MHz - 178MHz Gain (dB) IF Frequency / Gain Setting (dB) or -Pin (dBm) -40degC / Channel A -40degC / Channel B 25degC / Channel A 25degC / Channel B 105degC / Channel A 105degC / Channel B 27 25 23 21 19 17 27 25 23 21 19 17 27 25 23 21 19 17 98MHz - 138MHz - 178MHz Output IP3 (dBm) IF Frequency / Gain Setting (dB) or -Pin (dBm) -40degC / Channel A -40degC / Channel B 25degC / Channel A 25degC / Channel B 105degC / Channel A 105degC / Channel B 100 27 25 23 21 19 17 27 25 23 21 19 17 27 25 23 21 19 17 98MHz - 138MHz - 178MHz Output IP2 (dBm) IF Frequency / Gain Setting (dB) or -Pin (dBm) -40degC / Channel A -40degC / Channel B 25degC / Channel A 25degC / Channel B 105degC / Channel A 105degC / Channel B

Sampling IF Receiver 1710MHz to 2050MHz FlatNoiseTM, Zero-DistortionTM, SIF Rx 26 Rev2, January 2014 IDTF0552NLGI Datasheet F0552NBGI Advance Datasheet TOCS [STD MODE, IF = 138M, LS INJECTION] 2X2, 3X3, LEAKAGE (-15-) 2 X 2 vs. TCASE [1.71 GHz RF] 3 x 3 vs. TCASE [1.71 GHz RF] LO to IF Leakage vs. TCASE [1.71 GHz RF] 2 X 2 vs. TCASE [1.88 GHz RF] 3 x 3 vs. TCASE [1.88 GHz RF] LO to IF Leakage vs. TCASE [1.88 GHz RF] -100 -90 -80 -70 -60 -50 -40 -30 -20 27 25 23 21 19 17 27 25 23 21 19 17 27 25 23 21 19 17 98MHz - 138MHz - 178MHz 2 x 2 Rejection (dBc) IF Frequency / Gain Setting (dB) or -Pin (dBm) -40degC / Channel A -40degC / Channel B 25degC / Channel A 25degC / Channel B 105degC / Channel A 105degC / Channel B -100 -90 -80 -70 -60 -50 -40 -30 -20 27 25 23 21 19 17 27 25 23 21 19 17 27 25 23 21 19 17 98MHz - 138MHz - 178MHz 3 x 3 Rejection (dBc) IF Frequency / Gain Setting (dB) or -Pin (dBm) -40degC / Channel A -40degC / Channel B 25degC / Channel A 25degC / Channel B 105degC / Channel A 105degC / Channel B -65 -60 -55 -50 -45 -40 -35 -30 -25 27 25 23 21 19 17 27 25 23 21 19 17 27 25 23 21 19 17 98MHz - 138MHz - 178MHz LO to IF Leakage (dBm) IF Frequency / Gain Setting (dB) or -Pin (dBm) -40degC / Channel A -40degC / Channel B 25degC / Channel A 25degC / Channel B 105degC / Channel A 105degC / Channel B -100 -90 -80 -70 -60 -50 -40 -30 -20 27 25 23 21 19 17 27 25 23 21 19 17 27 25 23 21 19 17 98MHz - 138MHz - 178MHz 2 x 2 Rejection (dBc) IF Frequency / Gain Setting (dB) or -Pin (dBm) -40degC / Channel A -40degC / Channel B 25degC / Channel A 25degC / Channel B 105degC / Channel A 105degC / Channel B -100 -90 -80 -70 -60 -50 -40 -30 -20 27 25 23 21 19 17 27 25 23 21 19 17 27 25 23 21 19 17 98MHz - 138MHz - 178MHz 3 x 3 Rejection (dBc) IF Frequency / Gain Setting (dB) or -Pin (dBm) -40degC / Channel A -40degC / Channel B 25degC / Channel A 25degC / Channel B 105degC / Channel A 105degC / Channel B -65 -60 -55 -50 -45 -40 -35 -30 -25 27 25 23 21 19 17 27 25 23 21 19 17 27 25 23 21 19 17 98MHz - 138MHz - 178MHz LO to IF Leakage (dBm) IF Frequency / Gain Setting (dB) or -Pin (dBm) -40degC / Channel A -40degC / Channel B 25degC / Channel A 25degC / Channel B 105degC / Channel A 105degC / Channel B

Sampling IF Receiver 1710MHz to 2050MHz FlatNoiseTM, Zero-DistortionTM, SIF Rx 27 Rev2, January 2014 IDTF0552NLGI Datasheet F0552NBGI Advance Datasheet TOCS [STD MODE, IF = 138M, LS INJECTION] OIP3, OIP3, 2X2 (-16-) Output IP3 [1.71 GHz RF] Output IP2 [1.71 GHz RF] 2x2 Rejection [1.71 GHz RF] Output IP3 [1.88 GHz RF] Output IP2 [1.88 GHz RF] 2x2 Rejection [1.88 GHz RF] -22-18-14-10-6-2261014182226 Output IP3 (dBm) Gain Setting (dB) / ~Pin (dBm) -40degC / Channel A -40degC / Channel B 25degC / Channel A 25degC / Channel B 105degC / Channel A 105degC / Channel B -22-18-14-10-6-2261014182226 Output IP2 (dBm) Gain Setting (dB) / ~Pin (dBm) -40degC / Channel A -40degC / Channel B 25degC / Channel A 25degC / Channel B 105degC / Channel A 105degC / Channel B -100 -90 -80 -70 -60 -50 -40 -30 -20 -22-18-14-10-6-2261014182226 2 x 2 Rejection (dBc) Gain Setting (dB) / ~Pin (dBm) -40degC / Channel A -40degC / Channel B 25degC / Channel A 25degC / Channel B 105degC / Channel A 105degC / Channel B -22-18-14-10-6-2261014182226 Output IP3 (dBm) Gain Setting (dB) / ~Pin (dBm) -40degC / Channel A -40degC / Channel B 25degC / Channel A 25degC / Channel B 105degC / Channel A 105degC / Channel B -22-18-14-10-6-2261014182226 Output IP2 (dBm) Gain Setting (dB) / ~Pin (dBm) -40degC / Channel A -40degC / Channel B 25degC / Channel A 25degC / Channel B 105degC / Channel A 105degC / Channel B -100 -90 -80 -70 -60 -50 -40 -30 -20 -22-18-14-10-6-2261014182226 2 x 2 Rejection (dBc) Gain Setting (dB) / ~Pin (dBm) -40degC / Channel A -40degC / Channel B 25degC / Channel A 25degC / Channel B 105degC / Channel A 105degC / Channel B

Sampling IF Receiver 1710MHz to 2050MHz FlatNoiseTM, Zero-DistortionTM, SIF Rx 28 Rev2, January 2014 IDTF0552NLGI Datasheet F0552NBGI Advance Datasheet TOCS [STD MODE, IF = 138M, LS INJECTION] 3X3, LEAKAGE (-17-) 3x3 Rejection [1.71 GHz RF] LO to IF Leakage [1.71 GHz RF] RF to IF Leakage [1.71 GHz RF] 3x3 Rejection [1.88 GHz RF] LO to IF Leakage [1.88 GHz RF] RF to IF Leakage [1.88 GHz RF] -100 -90 -80 -70 -60 -50 -40 -30 -20 -22-18-14-10-6-2261014182226 3 x 3 Rejection (dBc) Gain Setting (dB) / ~Pin (dBm) -40degC / Channel A -40degC / Channel B 25degC / Channel A 25degC / Channel B 105degC / Channel A 105degC / Channel B -100 -90 -80 -70 -60 -50 -40 -30 -20 -22-18-14-10-6-2261014182226 LO to IF Leakage (dBm) Gain Setting (dB) / ~Pin (dBm) -40degC / Channel A -40degC / Channel B 25degC / Channel A 25degC / Channel B 105degC / Channel A 105degC / Channel B -100 -90 -80 -70 -60 -50 -40 -30 -20 -22-18-14-10-6-2261014182226 RF to IF Leakage (dBc) Gain Setting (dB) / ~Pin (dBm) -40degC / Channel A -40degC / Channel B 25degC / Channel A 25degC / Channel B 105degC / Channel A 105degC / Channel B -100 -90 -80 -70 -60 -50 -40 -30 -20 -22-18-14-10-6-2261014182226 3 x 3 Rejection (dBc) Gain Setting (dB) / ~Pin (dBm) -40degC / Channel A -40degC / Channel B 25degC / Channel A 25degC / Channel B 105degC / Channel A 105degC / Channel B -100 -90 -80 -70 -60 -50 -40 -30 -20 -22-18-14-10-6-2261014182226 LO to IF Leakage (dBm) Gain Setting (dB) / ~Pin (dBm) -40degC / Channel A -40degC / Channel B 25degC / Channel A 25degC / Channel B 105degC / Channel A 105degC / Channel B -100 -90 -80 -70 -60 -50 -40 -30 -20 -22-18-14-10-6-2261014182226 RF to IF Leakage (dBc) Gain Setting (dB) / ~Pin (dBm) -40degC / Channel A -40degC / Channel B 25degC / Channel A 25degC / Channel B 105degC / Channel A 105degC / Channel B

Sampling IF Receiver 1710MHz to 2050MHz FlatNoiseTM, Zero-DistortionTM, SIF Rx 29 Rev2, January 2014 IDTF0552NLGI Datasheet F0552NBGI Advance Datasheet TYPICAL OPERATING CONDITIONS (STD MODE, 276MHZ IF) Unless otherwise noted, the following conditions apply to the 276MHz Typ Ops Graphs:  BOM2 Applications circuit with 276 MHz IF Center +/- 40 MHz bandwidth network to provide matching to 100 ohm differential load provided by 2:1 transformer (see page 51)  Pout ~ +1 dBm  PIN from -27 to -6 dBm (Gain Setting Adjusted to yield Pout ~ +1 dBm without exceeding -6 dBm PIN)  Tone Spacing = 800 KHz  Device configured in Standard Mode with Low Side Injection  TCASE = 25C, VCC = 5.00 V, LO Power = 0 dBm  RF Frequency: 1.88 GHz  IF Frequency: 276 MHz  Transformer Losses are de-embedded  Input RF trace Losses are not de-embedded

Sampling IF Receiver 1710MHz to 2050MHz FlatNoiseTM, Zero-DistortionTM, SIF Rx 30 Rev2, January 2014 IDTF0552NLGI Datasheet F0552NBGI Advance Datasheet TOCS [MAX GAIN, IF = 276M, STD MODE] GAIN, OIP3, OIP2 (-18-) Gain vs. TCASE [low side inj.] Output IP3 vs. TCASE [low side inj.] Output IP2 vs. TCASE [low side inj.] Gain vs. TCASE [high side inj.] Output IP3 vs. TCASE [high side inj.] Output IP2 vs. TCASE [high side inj.] 236M 276M 316M 236M 276M 316M 1.71 GHz 1.88 GHz -40 - Channel A -40 - Channel B 25 - Channel A 25 - Channel B 105 - Channel A 105 - Channel B Gain (dB) RF Freq / IF Freq 236M 276M 316M 236M 276M 316M 1.71 GHz 1.88 GHz -40 - Channel A -40 - Channel B 25 - Channel A 25 - Channel B 105 - Channel A 105 - Channel B RF Freq / IF Freq Output IP3 (dBm) 100 236M 276M 316M 236M 276M 316M 1.71 GHz 1.88 GHz -40 - Channel A -40 - Channel B 25 - Channel A 25 - Channel B 105 - Channel A 105 - Channel B Output IP2 (dBm) RF Freq / IF Freq 276M 276M 1.71 GHz 1.88 GHz -40 - Channel A -40 - Channel B 25 - Channel A 25 - Channel B 105 - Channel A 105 - Channel B Gain (dB) RF Freq / IF Freq 276M 276M 1.71 GHz 1.88 GHz -40 - Channel A -40 - Channel B 25 - Channel A 25 - Channel B 105 - Channel A 105 - Channel B RF Freq / IF Freq Output IP3 (dBm) 100 276M 276M 1.71 GHz 1.88 GHz -40 - Channel A -40 - Channel B 25 - Channel A 25 - Channel B 105 - Channel A 105 - Channel B Output IP2 (dBm) RF Freq / IF Freq

Sampling IF Receiver 1710MHz to 2050MHz FlatNoiseTM, Zero-DistortionTM, SIF Rx 31 Rev2, January 2014 IDTF0552NLGI Datasheet F0552NBGI Advance Datasheet TOCS [MAX GAIN, IF = 276M, STD MODE] 2X2, 3X3, LEAKAGE (-19-) 2 X 2 vs. TCASE [low side inj.] 3 x 3 vs. TCASE [low side inj.] LO to IF Leakage vs. TCASE [low side inj.] 2 X 2 vs. TCASE [high side inj.] 3 x 3 vs. TCASE [high side inj.] LO to IF Leakage vs. TCASE [high side inj.] -100 -90 -80 -70 -60 -50 -40 -30 -20 236M 276M 316M 236M 276M 316M 1.71 GHz 1.88 GHz -40 degC - Channel A -40 degC - Channel B 25 degC - Channel A 25 degC - Channel B 105 degC - Channel A 105 degC - Channel B 2X2 Rejection (dBc) RF Freq / IF Freq -100 -90 -80 -70 -60 -50 -40 -30 -20 236M 276M 316M 236M 276M 316M 1.71 GHz 1.88 GHz -40 degC - Channel A -40 degC - Channel B 25 degC - Channel A 25 degC - Channel B 105 degC - Channel A 105 degC - Channel B 3x3 Rejection (dBc) RF Freq / IF Freq -65 -60 -55 -50 -45 -40 -35 -30 -25 236M 276M 316M 236M 276M 316M 1.71 GHz 1.88 GHz -40 degC - Channel A -40 degC - Channel B 25 degC - Channel A 25 degC - Channel B 105 degC - Channel A 105 degC - Channel B LO to IF Leakage (dBm) RF Freq / IF Freq -100 -90 -80 -70 -60 -50 -40 -30 -20 276M 276M 1.71 GHz 1.88 GHz -40 degC - Channel A -40 degC - Channel B 25 degC - Channel A 25 degC - Channel B 105 degC - Channel A 105 degC - Channel B 2X2 Rejection (dBc) RF Freq / IF Freq -100 -90 -80 -70 -60 -50 -40 -30 -20 276M 276M 1.71 GHz 1.88 GHz -40 degC - Channel A -40 degC - Channel B 25 degC - Channel A 25 degC - Channel B 105 degC - Channel A 105 degC - Channel B 3x3 Rejection (dBc) RF Freq / IF Freq -65 -60 -55 -50 -45 -40 -35 -30 -25 276M 276M 1.71 GHz 1.88 GHz -40 degC - Channel A -40 degC - Channel B 25 degC - Channel A 25 degC - Channel B 105 degC - Channel A 105 degC - Channel B LO to IF Leakage (dBm) RF Freq / IF Freq

Sampling IF Receiver 1710MHz to 2050MHz FlatNoiseTM, Zero-DistortionTM, SIF Rx 32 Rev2, January 2014 IDTF0552NLGI Datasheet F0552NBGI Advance Datasheet TOCS SWEPT GAIN SETTING [STD MODE, IF =276M, LS INJECTION] GAIN, OIP3, IIP3 (-20-) Gain [1.71 GHz] Output IP3 [1.71 GHz] Input IP3 [1.71 GHz] Gain [1.88 GHz] Output IP3 [1.88 GHz] Input IP3 [1.88 GHz] -22 -18 -14 -10 -22-18-14-10-6-2261014182226 Gain (dB) Gain Setting (dB) / Pin (dBm) -40C / ChA -40C / ChB +25C / ChA +25C / ChB +105C / ChA +105C / ChB -22-18-14-10-6-2261014182226 Output IP3 (dBm) Gain Setting (dB) / Pin (dBm) -40C / ChA -40C / ChB +25C / ChA +25C / ChB +105C / ChA +105C / ChB -22-18-14-10-6-2261014182226 Input IP3 (dBm) Gain Setting (dB) / Pin (dBm) -40C / ChA -40C / ChB +25C / ChA +25C / ChB +105C / ChA +105C / ChB -22 -18 -14 -10 -22-18-14-10-6-2261014182226 Gain (dB) Gain Setting (dB) / Pin (dBm) -40C / ChA -40C / ChB +25C / ChA +25C / ChB +105C / ChA +105C / ChB -22-18-14-10-6-2261014182226 Output IP3 (dBm) Gain Setting (dB) / Pin (dBm) -40C / ChA -40C / ChB +25C / ChA +25C / ChB +105C / ChA +105C / ChB -22-18-14-10-6-2261014182226 Input IP3 (dBm) Gain Setting (dB) / Pin (dBm) -40C / ChA -40C / ChB +25C / ChA +25C / ChB +105C / ChA +105C / ChB

Sampling IF Receiver 1710MHz to 2050MHz FlatNoiseTM, Zero-DistortionTM, SIF Rx 33 Rev2, January 2014 IDTF0552NLGI Datasheet F0552NBGI Advance Datasheet TOCS SWEPT GAIN SETTING [STD MODE, IF =276M, LS INJECTION] OIP2, IIP2, 2X2 (-21-) Output IP2 [1.71 GHz] Input IP2 [1.71 GHz] 2x2 Rejection [1.71 GHz] Output IP2 [1.88 GHz] Input IP2 [1.88 GHz] 2x2 Rejection [1.88 GHz] -22-18-14-10-6-2261014182226 Output IP2 (dBm) Gain Setting (dB) / Pin (dBm) -40C / ChA -40C / ChB +25C / ChA +25C / ChB +105C / ChA +105C / ChB -22-18-14-10-6-2261014182226 Input IP2 (dBm) Gain Setting (dB) / Pin (dBm) -40C / ChA -40C / ChB +25C / ChA +25C / ChB +105C / ChA +105C / ChB -100 -90 -80 -70 -60 -50 -40 -30 -20 -22-18-14-10-6-2261014182226

2 X 2 Rejection (dBc)

Gain Setting (dB) / Pin (dBm) -40C / ChA -40C / ChB +25C / ChA +25C / ChB +105C / ChA +105C / ChB -22-18-14-10-6-2261014182226 Output IP2 (dBm) Gain Setting (dB) / Pin (dBm) -40C / ChA -40C / ChB +25C / ChA +25C / ChB +105C / ChA +105C / ChB -22-18-14-10-6-2261014182226 Input IP2 (dBm) Gain Setting (dB) / Pin (dBm) -40C / ChA -40C / ChB +25C / ChA +25C / ChB +105C / ChA +105C / ChB -100 -90 -80 -70 -60 -50 -40 -30 -20 -22-18-14-10-6-2261014182226 Gain Setting (dB) / Pin (dBm) -40C / ChA -40C / ChB +25C / ChA +25C / ChB +105C / ChA +105C / ChB

Sampling IF Receiver 1710MHz to 2050MHz FlatNoiseTM, Zero-DistortionTM, SIF Rx 34 Rev2, January 2014 IDTF0552NLGI Datasheet F0552NBGI Advance Datasheet TOCS SWEPT GAIN SETTING [STD MODE, IF =276M, LS INJECTION] 3X3, LEAKAGE (-22-) 3x3 Rejection [1.71 GHz] LO to IF Leakage [low side inj, 1.88 GHz] RF to IF Leakage [1.71 GHz] 3x3 Rejection [1.88 GHz] LO to IF Leakage [high side inj., 1.88 GHz] RF to IF Leakage [1.88 GHz] -100 -90 -80 -70 -60 -50 -40 -30 -20 -22-18-14-10-6-2261014182226

3 X 3 Rejection (dBc)

Gain Setting (dB) / Pin (dBm) -40C / ChA -40C / ChB +25C / ChA +25C / ChB +105C / ChA +105C / ChB -76 -72 -68 -64 -60 -56 -52 -48 -44 -40 -36 -32 -28 -24 -22-18-14-10-6-2261014182226 LO to IF Leakage (dBm) Gain Setting (dB) / Pin (dBm) -40C / ChA -40C / ChB +25C / ChA +25C / ChB +105C / ChA +105C / ChB -100 -96 -92 -88 -84 -80 -76 -72 -68 -64 -60 -56 -52 -48 -22-18-14-10-6-2261014182226 RF to IF Leakage (dBm) Gain Setting (dB) / Pin (dBm) -40C / ChA -40C / ChB +25C / ChA +25C / ChB +105C / ChA +105C / ChB -100 -90 -80 -70 -60 -50 -40 -30 -20 -22-18-14-10-6-2261014182226 Gain Setting (dB) / Pin (dBm) -40C / ChA -40C / ChB +25C / ChA +25C / ChB +105C / ChA +105C / ChB -76 -72 -68 -64 -60 -56 -52 -48 -44 -40 -36 -32 -28 -24 -22-18-14-10-6-2261014182226 LO to IF Leakage (dBm) Gain Setting (dB) / Pin (dBm) -40C / ChA -40C / ChB +25C / ChA +25C / ChB +105C / ChA +105C / ChB -100 -96 -92 -88 -84 -80 -76 -72 -68 -64 -60 -56 -52 -48 -22-18-14-10-6-2261014182226 RF to IF Leakage (dBm) Gain Setting (dB) / Pin (dBm) -40C / ChA -40C / ChB +25C / ChA +25C / ChB +105C / ChA +105C / ChB

Sampling IF Receiver 1710MHz to 2050MHz FlatNoiseTM, Zero-DistortionTM, SIF Rx 35 Rev2, January 2014 IDTF0552NLGI Datasheet F0552NBGI Advance Datasheet TYPICAL OPERATING CONDITIONS (LC MODE, 184MHZ) Unless otherwise noted, the following conditions apply to the 184MHz LC Mode Typ Ops Graphs:  BOM2 Applications circuit for 100 ohm differential load with 184 MHz IF Center +/- 40 MHz BW into 2:1 Transformer (see page 51)  Pout ~ +1 dBm  PIN from -29 to -6 dBm (Gain Setting Adjusted to yield Pout ~ +1 dBm without exceeding -6 dBm PIN)  Tone Spacing = 800 KHz  Device configured in Standard Mode with Low Side Injection  TCASE = 25C, VCC = 5.00 V, LO Power = 0 dBm  RF Frequency: 1.88 GHz  IF Frequency: 184 MHz  Transformer Losses are de-embedded  Input RF trace Losses are not de-embedded 320 330 340 350 360 370 380 390 400 410 420 -22-18-14-10-6-2261014182226 Total ICC (mA) Gain Setting (dB) / Pin (dBm) -40degC / 1.71 GHz RF -40degC / 1.88 GHz RF 25degC / 1.71 GHz RF 25degC / 1.88 GHz RF 105degC / 1.71 GHz RF 105degC / 1.88 GHz RF

Sampling IF Receiver 1710MHz to 2050MHz FlatNoiseTM, Zero-DistortionTM, SIF Rx 36 Rev2, January 2014 IDTF0552NLGI Datasheet F0552NBGI Advance Datasheet TOCS SWEPT GAIN SETTING [LC MODE, IF =184M, LS INJECTION] GAIN, OIP3, IIP3 (-23-) Gain [1.71 GHz] Output IP3 [1.71 GHz] Input IP3 [1.71 GHz] Gain [1.88 GHz] Output IP3 [1.88 GHz] Input IP3 [1.88 GHz] -22 -18 -14 -10 -22-18-14-10-6-2261014182226 Gain (dB) Gain Setting (dB) / ~Pin (dBm) -40degC / Channel A -40degC / Channel B 25degC / Channel A 25degC / Channel B 105degC / Channel A 105degC / Channel B -22-18-14-10-6-2261014182226 Output IP3 (dBm) Gain Setting (dB) / ~Pin (dBm) -40degC / Channel A -40degC / Channel B 25degC / Channel A 25degC / Channel B 105degC / Channel A 105degC / Channel B -22-18-14-10-6-2261014182226 Input IP3 (dBm) Gain Setting (dB) / ~Pin (dBm) -40degC / Channel A -40degC / Channel B 25degC / Channel A 25degC / Channel B 105degC / Channel A 105degC / Channel B -22 -18 -14 -10 -22-18-14-10-6-2261014182226 Gain (dB) Gain Setting (dB) / ~Pin (dBm) -40degC / Channel A -40degC / Channel B 25degC / Channel A 25degC / Channel B 105degC / Channel A 105degC / Channel B -22-18-14-10-6-2261014182226 Output IP3 (dBm) Gain Setting (dB) / ~Pin (dBm) -40degC / Channel A -40degC / Channel B 25degC / Channel A 25degC / Channel B 105degC / Channel A 105degC / Channel B -22-18-14-10-6-2261014182226 Input IP3 (dBm) Gain Setting (dB) / ~Pin (dBm) -40degC / Channel A -40degC / Channel B 25degC / Channel A 25degC / Channel B 105degC / Channel A 105degC / Channel B

Sampling IF Receiver 1710MHz to 2050MHz FlatNoiseTM, Zero-DistortionTM, SIF Rx 37 Rev2, January 2014 IDTF0552NLGI Datasheet F0552NBGI Advance Datasheet TOCS SWEPT GAIN SETTING [LC MODE, IF =184M, LS INJECTION] OIP2, IIP2, 2X2 (-24-) Output IP2 [1.71 GHz] Input IP2 [1.71 GHz] 2x2 Rejection [1.71 GHz] Output IP2 [1.88 GHz] Input IP2 [1.88 GHz] 2x2 Rejection [1.88 GHz] -22-18-14-10-6-2261014182226 Output IP2 (dBm) Gain Setting (dB) / ~Pin (dBm) -40degC / Channel A -40degC / Channel B 25degC / Channel A 25degC / Channel B 105degC / Channel A 105degC / Channel B -22-18-14-10-6-2261014182226 Input IP2 (dBm) Gain Setting (dB) / ~Pin (dBm) -40degC / Channel A -40degC / Channel B 25degC / Channel A 25degC / Channel B 105degC / Channel A 105degC / Channel B -100 -90 -80 -70 -60 -50 -40 -30 -20 -22-18-14-10-6-2261014182226 2x2 Rejection (dBc) Gain Setting (dB) / ~Pin (dBm) -40degC / Channel A -40degC / Channel B 25degC / Channel A 25degC / Channel B 105degC / Channel A 105degC / Channel B -22-18-14-10-6-2261014182226 Output IP2 (dBm) Gain Setting (dB) / ~Pin (dBm) -40degC / Channel A -40degC / Channel B 25degC / Channel A 25degC / Channel B 105degC / Channel A 105degC / Channel B -22-18-14-10-6-2261014182226 Input IP2 (dBm) Gain Setting (dB) / ~Pin (dBm) -40degC / Channel A -40degC / Channel B 25degC / Channel A 25degC / Channel B 105degC / Channel A 105degC / Channel B -100 -90 -80 -70 -60 -50 -40 -30 -20 -22-18-14-10-6-2261014182226 2x2 Rejection (dBc) Gain Setting (dB) / ~Pin (dBm) -40degC / Channel A -40degC / Channel B 25degC / Channel A 25degC / Channel B 105degC / Channel A 105degC / Channel B

Sampling IF Receiver 1710MHz to 2050MHz FlatNoiseTM, Zero-DistortionTM, SIF Rx 38 Rev2, January 2014 IDTF0552NLGI Datasheet F0552NBGI Advance Datasheet TOCS SWEPT GAIN SETTING [LC MODE, IF =184M, LS INJECTION] 3X3, LEAKAGE (-25-) 3x3 Rejection [1.71 GHz] LO to IF Leakage [low side inj, 1.88 GHz] RF to IF Leakage [1.71 GHz] 3x3 Rejection [1.88 GHz] LO to IF Leakage [high side inj., 1.88 GHz] RF to IF Leakage [1.88 GHz] -100 -90 -80 -70 -60 -50 -40 -30 -20 -22-18-14-10-6-2261014182226 3x3 Rejection (dBc) Gain Setting (dB) / ~Pin (dBm) -40degC / Channel A -40degC / Channel B 25degC / Channel A 25degC / Channel B 105degC / Channel A 105degC / Channel B -100 -90 -80 -70 -60 -50 -40 -30 -20 -22-18-14-10-6-2261014182226 LO to IF Leakage (dBm) Gain Setting (dB) / ~Pin (dBm) -40degC / Channel A -40degC / Channel B 25degC / Channel A 25degC / Channel B 105degC / Channel A 105degC / Channel B -100 -90 -80 -70 -60 -50 -40 -30 -20 -22-18-14-10-6-2261014182226 RF to IF Leakage (dBm) Gain Setting (dB) / ~Pin (dBm) -40degC / Channel A -40degC / Channel B 25degC / Channel A 25degC / Channel B 105degC / Channel A 105degC / Channel B -100 -90 -80 -70 -60 -50 -40 -30 -20 -22-18-14-10-6-2261014182226 3x3 Rejection (dBc) Gain Setting (dB) / ~Pin (dBm) -40degC / Channel A -40degC / Channel B 25degC / Channel A 25degC / Channel B 105degC / Channel A 105degC / Channel B -100 -90 -80 -70 -60 -50 -40 -30 -20 -22-18-14-10-6-2261014182226 LO to IF Leakage (dBm) Gain Setting (dB) / ~Pin (dBm) -40degC / Channel A -40degC / Channel B 25degC / Channel A 25degC / Channel B 105degC / Channel A 105degC / Channel B -100 -90 -80 -70 -60 -50 -40 -30 -20 -22-18-14-10-6-2261014182226 RF to IF Leakage (dBm) Gain Setting (dB) / ~Pin (dBm) -40degC / Channel A -40degC / Channel B 25degC / Channel A 25degC / Channel B 105degC / Channel A 105degC / Channel B

Sampling IF Receiver 1710MHz to 2050MHz FlatNoiseTM, Zero-DistortionTM, SIF Rx 39 Rev2, January 2014 IDTF0552NLGI Datasheet F0552NBGI Advance Datasheet TOCS SWEPT GAIN SETTING [LC MODE, IF =184M, LS INJECTION] CHA ISO (-26-) Channel Isolation [ChA to ChB] Channel Isolation [ChB to ChA] 1700 1750 1800 1850 1900 1950 2000 2050 ChA to ChB Isolation (dBc) RF Frequency (MHz) IF = 134 MHz IF = 184 MHz IF = 224 MHz 1700 1750 1800 1850 1900 1950 2000 2050 ChB to ChA Isolation (dBc) RF Frequency (MHz) IF = 134 MHz IF = 184 MHz IF = 224 MHz

Sampling IF Receiver 1710MHz to 2050MHz FlatNoiseTM, Zero-DistortionTM, SIF Rx 40 Rev2, January 2014 IDTF0552NLGI Datasheet F0552NBGI Advance Datasheet TOCS RETURN LOSS [STD MODE] (-27-) IF_A Output Return Loss 138M, 184M match IF_A Return Loss 276MHz match RF Input Return Loss IF_A Output Return Loss 330MHz match IF_B Return Loss 276MHz match LO Input Return Loss -40 -35 -30 -25 -20 -15 -10 84 104 124 144 164 184 204 224 244 264 284 G=27 dB G=20 dB G=10 dB G=0 dB G=-10 dB G=-20 dB IF Frequency (MHz) IF_A Return Loss (dB) -40 -35 -30 -25 -20 -15 -10 176 196 216 236 256 276 296 316 336 356 376 G-20 G10 G15 G17 G20 G23 G25 G27 IF Frequency (MHz) IF_A Return Loss (dB) -40 -35 -30 -25 -20 -15 -10 1400 1500 1600 1700 1800 1900 2000 2100 2200 2300 2400 LO=1800 MHz LO=1900 MHz LO=2000 MHz LO=2100 MHz LO=2200 MHz LO=2300 MHz RF Frequency (MHz) RF Return Loss (dB) -50 -45 -40 -35 -30 -25 -20 -15 -10 230 250 270 290 310 330 350 370 390 410 430 IF Return Loss (dB) IF Frequency (MHz) G27 G17 G-20 -40 -35 -30 -25 -20 -15 -10 176 196 216 236 256 276 296 316 336 356 376 G-20 G10 G15 G17 G20 G23 G25 G27 IF Frequency (MHz) IF_B Return Loss (dB) -40 -35 -30 -25 -20 -15 -10 1200 1400 1600 1800 2000 2200 2400 LO match LO Frequency (MHz) LO Port Return Loss (dB)

Sampling IF Receiver 1710MHz to 2050MHz FlatNoiseTM, Zero-DistortionTM, SIF Rx 41 Rev2, January 2014 IDTF0552NLGI Datasheet F0552NBGI Advance Datasheet TOCS HISTOGRAMS [N= 1090, TCASE = 25C] (-28-) Gain [RF = 1880M, LO =1696M, GMAX] ATTN Accuracy1 [RF = 1880M, LO =1696, ChA] ICC STD Mode [LO =1696M, VCC = 5.00 V] Output IP3 [RF = 1880M, LO =1696M, GMAX] ATTN Accuracy2 [RF = 1880M, LO =1696, ChA] ICC LC Mode [LO =1696M, VCC = 5.00 V] 10% 15% 20% 25% 30% 35%Percent Gain Bin (dB) Channel A Channel B 10% 20% 30% 40% 50% 60% 70% Percent Attenuation Accuracy Bin (dB) 8dB ATTN 16dB ATTN 10% 15% 20% 25% 30% 35% Percent Total ICC Bin (mA) STD Mode 10% 15% 20% 25% Percent Output IP3 Bin (dBm) Channel A Channel B 10% 15% 20% 25% 30% 35% Percent Attenuation Accuracy Bin (dB) 32dB ATTN 47dB ATTN 10% 15% 20% 25% 30% 35% Percent Total ICC Bin (mA) LC Mode

Sampling IF Receiver 1710MHz to 2050MHz FlatNoiseTM, Zero-DistortionTM, SIF Rx 42 Rev2, January 2014 IDTF0552NLGI Datasheet F0552NBGI Advance Datasheet PACKAGE DRAWING (10X10 68-PIN THIN QFN)

Sampling IF Receiver 1710MHz to 2050MHz FlatNoiseTM, Zero-DistortionTM, SIF Rx 43 Rev2, January 2014 IDTF0552NLGI Datasheet F0552NBGI Advance Datasheet F0552 PINOUT IDTF0552/0502/0562NLGI 68B5 NC VCC ISET_B GND IFOUT_B+ IFOUT_B- NC NC NC MX_IF_BiasB NC MX_IFB+ MX_IFB- GND VCC GND VCC LO1_Adj GND GND LO_IN LO_IN_RTN VCC LO2_Adj GND NC MX_IFA- MX_IFA+ NC MX_IF_BiasA NC NC GND IFOUT_A- IFOUT_A+ GND ISET_A VCC NC VCC GND VCC GND RFIN_A GND NC TDD_A LCmode TDD_B NC GND RFIN_B GND VCC GND VCC

Sampling IF Receiver 1710MHz to 2050MHz FlatNoiseTM, Zero-DistortionTM, SIF Rx 44 Rev2, January 2014 IDTF0552NLGI Datasheet F0552NBGI Advance Datasheet F0552 PIN DESCRIPTION TABLE Pin Name Function 1, 3, 15, 17, 25, 38, 40, 46, VCC Power Supply. Bypass to GND with capacitors shown in the Typical Application Circuit as close as possible to pin. 2, 4, 6, 12, 14, 16, 27, 37, 39, 42, 43, 48, 56, GND Ground these pins. 5 RFIN_A Main Channel RF Input. Internally matched to 50Ω. DO NOT apply DC to these pins 7, 11, 24, 30, 31, 32, 34, 49, 52, 54, 55, 62 NC No Connection. Not internally connected. OK to connect to VCC, OK to connect to GND

8 TDD_A

Standby control for Channel A. Includes an internal pull-up resistor so leave as NC for Standby mode. Set this pin to low or GND for normal operation. 9 LCmode Low_Current Mode. Includes an internal pull-up resistor so leave as NC for LC mode. Set this pin to low or GND for STD mode.

10 TDD_B

Standby control for Channel B. Includes an internal pull-up resistor so leave as NC for Standby mode. Set this pin to low or GND for normal operation. 13 RFIN_B Diversity Channel RF Input. Internally matched to 50Ω 18 B5 Parallel Gain Control Input – MSB. Includes an internal pull-up resistor. 19 B4 Parallel Gain Control Input. Includes an internal pull-up resistor. 20 B3 Parallel Gain Control Input. Includes an internal pull-up resistor. 21 B2 Parallel Gain Control Input. Includes an internal pull-up resistor. 22 B1 Parallel Gain Control Input. Includes an internal pull-up resistor. 23 B0 Parallel Gain Control Input – LSB (1 dB step). Includes an internal pull-up resistor. 26 ISET_B ChB VGA Icc set: Recommended resistor value = 3.83K 28 IFOUT_B+ Channel B Differential Output +. Pull up to Vcc through an inductor 29 IFOUT_B- Channel B Differential Output -. Pull up to Vcc through an inductor

33 MX_IF_BiasB

Connect the specified resistor for either Standard mode (41ohm) or LC mode (62ohm) from this pin to ground to set the bias for the Diversity IF amplifier. This is NOT a current set resistor. 35 MX_IFB+ Diversity Mixer Differential IF (+) Output. Connect a pullup inductor from this pin to VCC. 36 MX_IFB- Diversity Mixer Differential IF (-) Output. Connect a pullup inductor from this pin to VCC.

Sampling IF Receiver 1710MHz to 2050MHz FlatNoiseTM, Zero-DistortionTM, SIF Rx 45 Rev2, January 2014 IDTF0552NLGI Datasheet F0552NBGI Advance Datasheet F0552 PIN DESCRIPTION TABLE (CONTINUED)

41 LO1_ADJ

Connect the specified resistor for either Standard mode (220ohm) or LC mode (240ohm) from this pin to ground to set the LO common buffer Icc. 44 LO_IN Local Oscillator Input. Connect the LO to this port through the recommended coupling capacitor. 45 LO_IN_RTN Transformer ground return. Ground this pin.

47 LO2_ADJ

Connect the specified resistor for either Standard mode (1.3K) or LC mode (2.15K) from this pin to ground to set the LO drive buffers Icc. 50 MX_IFA- Diversity Mixer Differential IF (-) Output. Connect a pullup inductor from this pin to VCC. 51 MX_IFA+ Diversity Mixer Differential IF (+) Output. Connect a pullup inductor from this pin to VCC.

53 MX_IF_BiasA

Connect the specified resistor for either Standard mode (41ohm) or LC mode (62ohm) from this pin to ground to set the bias for the Diversity IF amplifier. This is NOT a current set resistor. 57 IFOUT_A- Channel A Differential Output -. Pull up to Vcc through an inductor 58 IFOUT_A+ Channel A Differential Output +. Pull up to Vcc through an inductor 60 ISET_A ChA VGA Icc set: Recommended resistor value = 3.83K 63 A0 Parallel Gain Control Input – LSB (1dB step). Includes an internal pull-up resistor. 64 A1 Parallel Gain Control Input. Includes an internal pull-up resistor. 65 A2 Parallel Gain Control Input. Includes an internal pull-up resistor. 66 A3 Parallel Gain Control Input. Includes an internal pull-up resistor. 67 A4 Parallel Gain Control Input. Includes an internal pull-up resistor. 68 A5 Parallel Gain Control Input – MSB. Includes an internal pull-up resistor. — EP Exposed Pad. Internally connected to GND. Solder this exposed pad to a PCB pad that uses multiple ground vias to provide heat transfer out of the device into the PCB ground planes. These multiple via grounds are also required to achieve the noted RF performance.

Sampling IF Receiver 1710MHz to 2050MHz FlatNoiseTM, Zero-DistortionTM, SIF Rx 46 Rev2, January 2014 IDTF0552NLGI Datasheet F0552NBGI Advance Datasheet F0552 DIGITAL PIN VOLTAGE & RESISTANCE VALUES The following table provides open-circuit DC voltage and resistance values referenced to ground for each of the control pins listed. Pin Name DC voltage (volts) Pull-up Resistance (ohms)

8 TDD_A 5 50k

9 LC_MODE 5 50k

10 TDD_B 5 50k

18 – 23 B0-B5 5 50k 63 - 68 A0-A5 5 50k

Sampling IF Receiver 1710MHz to 2050MHz FlatNoiseTM, Zero-DistortionTM, SIF Rx 47 Rev2, January 2014 IDTF0552NLGI Datasheet F0552NBGI Advance Datasheet APPLICATIONS INFORMATION Power Supplies A common VCC power supply should be used for all pins requiring DC power. All supply pins should be bypassed with external capacitors to minimize noise and fast transients. Supply noise can degrade noise figure and fast transients can trigger ESD clamps and cause them to fail. Supply voltage change or transients should have a slew rate smaller than 1V/20uS. In addition, all control pins should remain at 0V (+/-0.3V) while the supply voltage ramps or while it returns to zero. Control Pin Interface If control signal integrity is a concern and clean signals cannot be guaranteed due to overshoot, undershoot, ringing, etc., provisions for an R-C circuit at the input of each control and data pin is recommended. This applies to pins 8, 9, 10, 18 - 23, and 63 - 68 as shown below. IDTF0552/0502/0562NLGI B3 B2 TDD_A LCmode TDD_B 5Kohm 2pf 5Kohm 2pf 5Kohm 2pf 5Kohm 2pf 5Kohm 2pf 5Kohm 2pf 5Kohm 2pf 5Kohm 2pf 5Kohm 2pf 5Kohm 2pf 5Kohm 2pf 5Kohm 2pf 5Kohm 2pf 5Kohm 2pf 5Kohm 2pf

Sampling IF Receiver 1710MHz to 2050MHz FlatNoiseTM, Zero-DistortionTM, SIF Rx 48 Rev2, January 2014 IDTF0552NLGI Datasheet F0552NBGI Advance Datasheet EVKIT & TYPICAL APPLICATION SCHEMATIC The following schematic describes the recommended EVkit and applications circuit. Note: Unless otherwise specified, all caps are 0402, 50V

Sampling IF Receiver 1710MHz to 2050MHz FlatNoiseTM, Zero-DistortionTM, SIF Rx 49 Rev2, January 2014 IDTF0552NLGI Datasheet F0552NBGI Advance Datasheet SCHEMATIC CONTINUED FROM PREVIOUS PAGE

Sampling IF Receiver 1710MHz to 2050MHz FlatNoiseTM, Zero-DistortionTM, SIF Rx 50 Rev2, January 2014 IDTF0552NLGI Datasheet F0552NBGI Advance Datasheet EVKIT PICTURE LEAVE OPEN FOR LC MODE, SHORT FOR STD MODE INSTALL JUMPER IN OUTER POSITION FOR CHANNEL A STD MODE INNER POSITION FOR CHANNEL A LC MODE SHORT FOR CHANNEL A NORMAL OPERATION LEAVE OPEN CHANNEL A STBY MODE SHORT FOR CHANNEL B NORMAL OPERATION LEAVE OPEN CHANNEL B STBY MODE INSTALL JUMPER IN OUTER POSITION FOR STD MODE INNER POSITION FOR LC MODE INSTALL JUMPER IN OUTER POSITION FOR CHANNEL B STD MODE INNER POSITION FOR CHANNEL B LC MODE

Sampling IF Receiver 1710MHz to 2050MHz FlatNoiseTM, Zero-DistortionTM, SIF Rx 51 Rev2, January 2014 IDTF0552NLGI Datasheet F0552NBGI Advance Datasheet F0552 BOM 1 & 2 Two EV Kit BOMs are included: BOM1 supports the 4:1 output transformation from 200ohms to 50ohms used for production test and BOM2 supports the 2:1 output transformation from 200ohms to 100ohms used to generate the typical operating curve graphs. BOM1 includes components for 4:1 output transformation supporting production test (IF center frequency 184MHz) BOM2 includes components for 2:1 output transformation used for TOCs (IF center frequency 184MHz +/ - 40MHz) For the complete list of matching values for IF frequencies other than 184MHz, see the following table. F0552 BOM For 4:1 IF=184Mhz for Correlation Item # Value Size Desc Mfr. Part # Mfr. Supplier Part # Supplier Part Reference Qty 1 18pF 0402 CAP CER 18pF 50V 5% C0G 0402 GRM1555C1H180JZ01DMURATA 490-1281-1-ND Digikey C3,4 2 2 39pF 0402 CAP CER 39pF 50V 5% C0G 0402 GRM1555C1H390JZ010MURATA 490-1286-1-ND Digikey C19 1 3 1000pF 0402 CAP CER 1000PF 50V C0G 0402 GRM1555C1H102JA01DMURATA 490-3244-1-ND Digikey C9,12,24,27 4 4 10nF 0402 CAP CER 10000PF 16V 10% X7R 0402 GRM155R71C103KA01DMURATA 490-1313-1-ND Digikey C1,2,5,6,7,10,11,14,15, 5 10uF 0603 CAP CER 10UF 6.3V X5R 0603 GRM188R60J106ME47DMURATA 490-3896-1-ND Digikey C31 1 6 220 0402 RES 220 OHM 1/10W 1% 0402 SMD ERJ-2RKF2200X Panasonic P220LCT-ND Digikey R15 1 7 240 0402 RES 240 OHM 1/10W 1% 0402 SMD ERJ-2RKF2400X Panasonic P240LCT-ND Digikey R16 1 8 1.3K 0402 RES 1.30K OHM 1/10W 1% 0402 SMD ERJ-2RKF1301X Panasonic P1.30KLCT-ND Digikey R18 1 9 2.15k 0402 RES 2.15K OHM 1/10W 1% 0402 SMD ERJ-2RKF2151X Panasonic P2.15KLCT-ND Digikey R19 1 10 62 0402 RES 62.0 OHM 1/10W 1% 0402 SMD ERJ-2RKF62R0X Panasonic P62.0LCT-ND Digikey R10,21 2 11 3.83K 0402 RES 3.83K OHM 1/10W 1% 0402 SMD ERJ-2RKF3831X Panasonic P3.83KLCT-ND Digikey R9,24 2 12 40.2 0402 RES 40.2 OHM 1/10W 1% 0402 SMD ERJ-2RKF40R2X Panasonic P40.2LCT-ND Digikey R11,20 2 13 0 0402 RES 0.0 OHM 1/10W 0402 SMD ERJ-2GE0R00X Panasonic P0.0JCT-ND Digikey R1,2,12,13,14,17,25, L9 -1211 14 SMA_END_LAUNCH.062 SMA_END_LAUNCH (small) 142-0711-821 Emerson Johnson530-142-0711-821Mouser J6,12,14 3 15 SMA_END_LAUNCH.062 SMA_END_LAUNCH (Big) 142-0701-851 Emerson Johnson530-142-0701-851Mouser J1,5,9 3

16 Header 14 Pin TH 14 CONN HEADER VERT SGL 14POS GOLDN2514-6002-RB 3M MHC14K-ND Digikey J15 1

17 Header 2 Pin TH 2 CONN HEADER VERT SGL 2POS GOLD 961102-6404-AR 3M 3M9447-ND Digikey J2,3,4,13 4

18 Header 3 Pin TH 3 CONN HEADER VERT SGL 3POS GOLD 961103-6404-AR 3M 3M9448-ND Digikey J7,8,10,11 4

19 1:4 Balun SM-22 4:1 Center Tap Balun TC4-1WG2+ Mini Circuits TC4-1WG2+ Mini Circuits T1,2 2 20 390 nH 0805 0805CS (2012) Ceramic Chip Inductor 0805CS-391XJLB COILCRAFT 0805CS-391XJLBCOILCRAFT L1-8 8

21 F0552 / Socket TQFN-68Sampling IF receiver / Socket F0552 IDT F0552 IDT U1 1

22 Not populated C13,25

23 PCB Rev 02 PCB Rev 02 F0552 EV Kit Rev 02 SBC 1

24 BOM Rev 04 F0552 BOM Rev 04

F0552 BOM For 2:1 IF=184Mhz Item # Value Size Desc Mfr. Part # Mfr. Supplier Part # Supplier Part Reference Qty 1 18pF 0402 CAP CER 18pF 50V 5% C0G 0402 GRM1555C1H180JZ01DMURATA 490-1281-1-ND Digikey C3,4 2 2 39pF 0402 CAP CER 39pF 50V 5% C0G 0402 GRM1555C1H390JZ010MURATA 490-1286-1-ND Digikey C19 1 3 20pF 0402 CAP CER 20pF 50V C0G 0402 GRM1555C1H200JZ01DMURATA 490-1282-1-ND Digikey C9,12,24,27 4 4 3pF 0402 CAP CER 3pF 50V C0G 0402 GRM1555C1H3R0CZ01DMURATA 490-3205-1-ND Digikey C13,25 2 5 10nF 0402 CAP CER 10000PF 16V 10% X7R 0402 GRM155R71C103KA01DMURATA 490-1313-1-ND Digikey C1,2,5,6,7,10,11,14 ,15, 6 10uF 0603 CAP CER 10UF 6.3V X5R 0603 GRM188R60J106ME47DMURATA 490-3896-1-ND Digikey C31 1 7 220 0402 RES 220 OHM 1/10W 1% 0402 SMD ERJ-2RKF2200X Panasonic P220LCT-ND Digikey R15 1 8 240 0402 RES 240 OHM 1/10W 1% 0402 SMD ERJ-2RKF2400X Panasonic P240LCT-ND Digikey R16 1 9 1.3K 0402 RES 1.30K OHM 1/10W 1% 0402 SMD ERJ-2RKF1301X Panasonic P1.30KLCT-ND Digikey R18 1 10 2.15k 0402 RES 2.15K OHM 1/10W 1% 0402 SMD ERJ-2RKF2151X Panasonic P2.15KLCT-ND Digikey R19 1 11 62 0402 RES 62.0 OHM 1/10W 1% 0402 SMD ERJ-2RKF62R0X Panasonic P62.0LCT-ND Digikey R10,21 2 12 3.83K 0402 RES 3.83K OHM 1/10W 1% 0402 SMD ERJ-2RKF3831X Panasonic P3.83KLCT-ND Digikey R9,24 2 13 40.2 0402 RES 40.2 OHM 1/10W 1% 0402 SMD ERJ-2RKF40R2X Panasonic P40.2LCT-ND Digikey R11,20 2 14 0 0402 RES 0.0 OHM 1/10W 0402 SMD ERJ-2GE0R00X Panasonic P0.0JCT-ND Digikey R1,2,12,13,14,17,25 7 15 SMA_END_LAUNCH.062 SMA_END_LAUNCH (small) 142-0711-821 Emerson Johnson530-142-0711-821Mouser J6,12,14 3 16 SMA_END_LAUNCH.062 SMA_END_LAUNCH (Big) 142-0701-851 Emerson Johnson530-142-0701-851Mouser J1,5,9 3

17 Header 14 Pin TH 14 CONN HEADER VERT SGL 14POS GOLDN2514-6002-RB 3M MHC14K-ND Digikey J15 1

18 Header 2 Pin TH 2 CONN HEADER VERT SGL 2POS GOLD 961102-6404-AR 3M 3M9447-ND Digikey J2,3,4,13 4

19 Header 3 Pin TH 3 CONN HEADER VERT SGL 3POS GOLD 961103-6404-AR 3M 3M9448-ND Digikey J7,8,10,11 4

20 2:1 Balun SM-22 2:1 Center Tap Balun TC2-72T+ Mini Circuits TC2-72T+ Mini Circuits T1,2 2 21 390 nH 0805 0805CS (2012) Ceramic Chip Inductor 0805CS-391XJLB COILCRAFT 0805CS-391XJLBCOILCRAFT L1,2,5,6 4 22 150nH 0805 0805CS (2012) Ceramic Chip Inductor 0805CS-151XJLB COILCRAFT 0805CS-151XJLB COILCRAFT L3,4,7,8 4 23 30nH 0402 0402CS Ceramic Chip Inductor 0402CS-30NXJLU COILCRAFT 0402CS-30NXJLU COILCRAFT L9-12 4

24 F0552 TQFN-68Sampling IF receiver F0552 IDT F0552 IDT U1 1

25 PCB Rev 02 PCB Rev 02 F0552 EV Kit Rev 02 SBC 1

26 BOM Rev 04 F0552 BOM Rev 04

Sampling IF Receiver 1710MHz to 2050MHz FlatNoiseTM, Zero-DistortionTM, SIF Rx 52 Rev2, January 2014 IDTF0552NLGI Datasheet F0552NBGI Advance Datasheet IF BIAS AND OUTPUT MATCHING CIRCUIT & BOM FOR VARIOUS IFS IF NETWORK BOM FOR DIFFERENT FREQUENCIES Item # Part Reference Value Unit IF frequency 80 (60-100) 138, 184 (98-240) 276 (190-316) 330 (250-410) MHz

1 C9,12,24,27 75 20 8 6 pF

2 C13,25 11 3 1.2 0.7 pF 3 C8,C32 0.6 0.6 0.6 0.6 pF

4 R23, R22 100 100 100 100 ohm

5 L3,4,7,8 220 150 82 56 nH

6 L9-12 36 30 24 18 nH

Sampling IF Receiver 1710MHz to 2050MHz FlatNoiseTM, Zero-DistortionTM, SIF Rx 53 Rev2, January 2014 IDTF0552NLGI Datasheet F0552NBGI Advance Datasheet TOP MARKINGS IDTF0552 NLGI ZB1343N Q31A007MY Part Number Date Code [YYWW] (Week 43 of 2013) Lot CodeDie Step

TOYOSU FORESIA, 3-2-24 Toyosu, Koto-ku, Tokyo 135-0061, Japan www.renesas.com Contact Information For further information on a product, technology, the most up-to-date version of a document, or your nearest sales office, please visit: www.renesas.com/contact/ Trademarks Renesas and the Renesas logo are trademarks of Renesas Electronics Corporation. All trademarks and registered trademarks are the property of their respective owners. IMPORTANT NOTICE AND DISCLAIMER RENESAS ELECTRONICS CORPORATION AND ITS SUBSIDIARIES (“RENESAS”) PROVIDES TECHNICAL SPECIFICATIONS AND RELIABILITY DATA (INCLUDING DATASHEETS), DESIGN RESOURCES (INCLUDING REFERENCE DESIGNS), APPLICATION OR OTHER DESIGN ADVICE, WEB TOOLS, SAFETY INFORMATION, AND OTHER RESOURCES “AS IS” AND WITH ALL FAULTS, AND DISCLAIMS ALL WARRANTIES, EXPRESS OR IMPLIED, INCLUDING, WITHOUT LIMITATION, ANY IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR NON-INFRINGEMENT OF THIRD PARTY INTELLECTUAL PROPERTY RIGHTS. These resources are intended for developers skilled in the art designing with Renesas products. You are solely responsible for (1) selecting the appropriate products for your application, (2) designing, validating, and testing your application, and (3) ensuring your application meets applicable standards, and any other safety, security, or other requirements. These resources are subject to change without notice. Renesas grants you permission to use these resources only for development of an application that uses Renesas products. Other reproduction or use of these resources is strictly prohibited. No license is granted to any other Renesas intellectual property or to any third party intellectual property. Renesas disclaims responsibility for, and you will fully indemnify Renesas and its representatives against, any claims, damages, costs, losses, or liabilities arising out of your use of these resources. Renesas' products are provided only subject to Renesas' Terms and Conditions of Sale or other applicable terms agreed to in writing. No use of any Renesas resources expands or otherwise alters any applicable warranties or warranty disclaimers for these products. (Rev.1.0 Mar 2020) © 2020 Renesas Electronics Corporation. All rights reserved.

Summary

Sampling IF Receiver 1710MHz to 2050MHz

Description