9313AA1

9313AAX KISTLER | Alldatasheet

Document overview

• Manufacturer or author: Provided By alldatasheet.com(free datasheet download site)
• PDF pages: 4

Technical content

0 … 50 N to 0 … 20 kN 9313_000-705e-03.23 © 2008 ... 2023 Kistler Group, Eulachstraße 22, 8408 Winterthur, Switzerland are protected by various intellectual property rights. For more details visit www.kistler.com. This information corresponds to the current state of knowledge. Kistler reserves the right to make technical changes. Liability for consequential damage resulting from the use of Kistler products is excluded. Type 9313AA1, 9313AA2 This lightweight miniature compression force sensor is particu- larly suitable for measuring dynamic forces and also quasistatic forces. Preloaded and provided with practical adaptation op- tions, the sensor is ready for immediate use. It comes in two different sizes which not only differ in their dimensions but also in their measuring ranges.

• Extremely wide measuring range with one sensor
• Calibration certificate for 3 measuring ranges: 100 %, 10 %, 1 %
• SCS calibration (optional)
• Easy adaptation using the axial threaded bores on both ends
• Easy to mount in connecting rods or plungers
• Low mass of the force introducing elements. Hence the dy- namic force curves remain largely unaffected
• Up to 100x overload capacity in the lower ranges in each case

Description

These press force sensors are based on the piezoelectric measur- ing principle. The force acting on the crystal element produces a proportional electric charge at the signal output. A measuring amplifier connected downstream to the sensor for example ICAM Type 5073A... typically converts this charge into a pro- cess signal which can be evaluated, for example 0 ... 10 V. The particularly square shape of the sensor body and the force introduction at both ends via axial threaded bores bring ad- vantages in special mounting situations. Tensile forces up to 10 % of the compression force range are measured. These ranges are not calibrated. However, they are often used for the detection of tool withdrawal forces, for example after press- fitting processes. Application The square geometry of the sensor makes it particularly usefull for confined spaces, such as mounting in force application dies and also for measurement of reaction force under workpiece holders. Because of the special properties of the piezoelectric measuring element – measuring accuracy is practically con- stant over a wide range of forces – the same press force sen- sor can be used for a large spectrum of forces. The facility to switch measuring ranges by using suitable amplifiers such as ICAM Type 5073A... provides an additional advantage here and thus allows for the general trend towards more compo- nent diversity in manufacturing and measuring stations. The wide-range measuring chain also offers decisive advantages in laboratory applications, where frequent change of sensors is a common occurrence. In addition, the extremely high overload capacity when using the respective lower measuring ranges makes preventive measures unnecessary. Fz Technical data Press Force Sensor Type 9313AA1 9313AA2 Measuring range Fz, max. kN 0 … 5 0 … 20 Measuring ranges, calibrated 1) 100 % kN 0 … 5 0 … 20 10 % kN 0 … 0,5 0 … 2 1 % kN 0 … 0,05 0 … 0,2 Overload tension/pressure, max. kN –0,5/5,5 –2/22 Threshold N 0,01 0,01 Sensitivity pC/N –10 –10

Press Force Sensor – 0 … 50 N to 0 … 20 kN, Type 9313AA1, 9313AA2 9313_000-705e-03.23 © 2008 ... 2023 Kistler Group, Eulachstraße 22, 8408 Winterthur, Switzerland are protected by various intellectual property rights. For more details visit www.kistler.com. This information corresponds to the current state of knowledge. Kistler reserves the right to make technical changes. Liability for consequential damage resulting from the use of Kistler products is excluded. Press Force Sensor Type 9313AA1 9313AA2 Linearity incl. Hysteresis 2) %FSO ≤±0,5 ≤±0,5 Tightening torque Mz, max. N·m 0,3 1,4 Temperature coefficient of sensitivity %/°C 0,05 0,05 Bending moment Mx,y, max. at Fz = 100 % N·m 0,2 0,6 at Fz = 0 % N·m 1,3 6 Shear force Fx,y, max. 3) kN 0,1 0,27 Crosstalk F x,y → Fz N/N <0,29 <0,65 Mx,y → Fz N/N·m <72 <98 Rigidity cz N/μm ≈560 ≈1 500 Natural frequency kHz >38 >35 Operating temperature range °C –40 … 120 Connector, electrical KIAG 10-32 neg. Protection class EN60529 with connected cable IP 65 with cable Type 1983AD... and welded sensor IP 67 Case material DIN 1.4542 Weight (without cable) grams 10 25 1) Only the compressive force direction is calibrated. Tensile force as 3) Equals lateral force at the joint shown above against "overload" is measurable but not calibrated 2) Relating to FSO of the respective calibrated (!) measuring range Dimensions [mm] Type D D1  H K T A B 9313AA1 13 5 11 10 M2,5 2,8 2 35 9313AA2 19 10 16 14 M4 4,2 3 40 Dimensions Types 9313AA1 and 9313AA2 e.g. O-ring Type 1100A59 Accessories e.g. Cable Type 1631C...

Press Force Sensor – 0 … 50 N to 0 … 20 kN, Type 9313AA1, 9313AA2 9313_000-705e-03.23 © 2008 ... 2023 Kistler Group, Eulachstraße 22, 8408 Winterthur, Switzerland are protected by various intellectual property rights. For more details visit www.kistler.com. This information corresponds to the current state of knowledge. Kistler reserves the right to make technical changes. Liability for consequential damage resulting from the use of Kistler products is excluded. General mounting instructions

• Off-center force introduction should be avoided. Introduce the force as concentrically as possible.
• Do not exceed the bending moments, shear forces or torques given in the table. Mechanical mounting of the sensor (examples) A: Sensor mounted in a connecting rod Push rod e.g. Type 9590A (Mounting stud) Push rod e.g. Type 9590A (Mounting stud) Joint MA FZ MA FZ Joint B: Sensor mounted with front on a press plunger to Type Type d4 H3 L1 P R1 SW 9313AA1 9500A00 6 3 1,9 M2,5 15 5 9313AA2 9500A01 10,5 5 2,9 M4 35 9
• Ensure all force transmission joint faces are maintained flat and free of dirt, oil or grease.
• The threaded connection tightening stop limit is the particu- lar joint face and not the end of the thread. The bottom of the threaded hole must not be reached. Mounting Stud Type 9590A... to Type Type d7 L L1 L2 L3 P SW 9313AA1 9590A7 5 12,5 1,9 2,5 10 M2,5 4,5 9313AA2 9590A8 10 20,5 2,9 5,5 15 M4 9 to Type Type d d1 d3 d5 d6 H2 N 9313AA1 9580A7 27 20 2,7 2,7 5,5 7 2,6 9313AA2 9580A8 35 27 3,2 4,3 8 8 4,5 Plunger Adapter flange Type 9580A7/A8 Force distributing cap Type 9500A00/A01

Press Force Sensor – 0 … 50 N to 0 … 20 kN, Type 9313AA1, 9313AA2 9313_000-705e-03.23 © 2008 ... 2023 Kistler Group, Eulachstraße 22, 8408 Winterthur, Switzerland are protected by various intellectual property rights. For more details visit www.kistler.com. This information corresponds to the current state of knowledge. Kistler reserves the right to make technical changes. Liability for consequential damage resulting from the use of Kistler products is excluded. Optional accessories Type/Mat. No.

• Flange 9580A…
• Force distributing cap 9500A…
• Mounting stud 9590A…
• Cleaning and insulating spray 250 ml 1003
• Connecting cable, KIAG 10-32 pos. – BNC pos. 1631C…
• Connecting cable, KIAG 10-32 pos. – TNC pos. 1633C…
• Connecting cable, KIAG 10-32 pos. – 1635C…
• Connecting cable, KIAG 10-32 pos. – 1900A23A11... KIAG 10-32 pos., highly flexible
• Connecting cable, KIAG 10-32 pos. – 1900A23A12... BNC pos., highly flexible For connection, extension, and connecting cables, see data sheet for Cables for Force, Torque, and Strain Sensors (Dok. No. 000-346). For cable connectors, couplings, and accessories, see data sheet for Coaxial Cable Connectors (Doc. No. 000-347). Ordering code
• Press Force Sensor 0 … 5 kN 9313AA1
• Press Force Sensor 0 … 20 kN 9313AA2 Electrical connection We recommend that only Kistler connection cables be used. Problems concerning insulation resistance, triboelectricity and Sensor Connecting cable Charge amplifier maXYmos Type 9313AA1/AA2 Type 1631C Type 5073A111 Type 5867B... cable breaks will then be avoided right from the start.