DATASHEET SEARCH SITE | WWW.ALLDATASHEET.COM
Document overview
- Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
- PDF pages: 3
Technical content
Instruction SheetSeating Tools 91318-[ ], 91319-[ ], and 91320-[ ] For Z-PACK* HS3 and Z-PACK 12-Row 408- -4571 LOC B 1 of 3E2010 Tyco Electronics Corporation, Harrisburg, PA All International Rights Reserved TE logo and Tyco Electronics are trademarks. *Trademark. Other products, logos, and company names used are the property of their respective owners. TOOLING ASSISTANCE CENTER 1- -800- - 722- -1111 PRODUCT INFORMATION 1- - 800- - 522- - 6752 This controlled document is subject to change. For latest revision and Regional Customer Service, visit our website atwww.tycoelectronics.com
12 MAR 10 Rev ABackplane Receptacle Connector Assemblies
- INTRODUCTION Seating Tools 91318- -[ ] are used to seat Z- -PACK 12- -row backplane receptacle connectors and Seating Tools 91319- -[ ] and 91320- -[ ] are used to seat Z- -PACK HS3 backplane receptacle connectors. The connectors have ACTION PIN contacts to allow solderless pc board installation. All dimensions on this instruction sheet are in metric units [with U.S. customary units in brackets]. Figures are not drawn to scale. Read these instructions and understand them before using the seating tools. Reasons for reissue of this instruction sheet are provided in Section 7, REVISION SUMMARY . 2. DESCRIPTION Each seating tool is a one- -piece design. During seating, the seating tool covers the connector and presses on the top surface of the connector when the applicator ram applies force to the seating tool. 3. REQUIREMENTS 3.1. PC Board Support Fixture (Customer Supplied) A pc board support must be used to provide proper support for the pc board and alignment of the seating tool to the connector contacts and to protect the pc board and connector from damage. Design the pc board support fixture using the recommendations in instruction sheet 408- -6927. Seating Tool Typical Z- -PACK HS3 Backplane Receptacle Connector Assembly (Ref) Printed Circuit (PC) Board (Ref) PC Board Support Fixture (Customer Supplied) ACTION PIN* Contact NOTE i
408- -4571Seating Tools 91318- -[ ], 91319- -[ ], and 91320- -[ ] 3 of 3Rev A Tyco Electronics Corporation 5. MAINTENANCE AND INSPECTION 5.1. Initial Inspection It is recommended that the seating tool be inspected using Figure 3 immediately upon arrival in your facility to ensure that it has not been damaged during shipment. 5.2. Daily Maintenance It is recommended that each operator be made aware of, and responsible for, the following steps of daily maintenance: 1. Remove dust, moisture, and other contaminants with a clean, soft brush, or lint- -free cloth. Do NOT use objects that could damage the tool or any of its components. 2. Ensure that the screws are in place and secured. 3. When the tool is not in use, store it in a clean, dry area. 5.3. Periodic Inspection Regular inspections should be performed by quality control personnel. A record of scheduled inspections should remain with the tool or be supplied to supervisory personnel responsible for the tool. The inspection frequency should be based on the amount of use, working conditions, operator training and skill, and established company standards. 6. REPLACEMENT The seating tool is not repairable. Order replacement seating tools through your representative, or call 1- -800- -526- -5142, or send a facsimile of your purchase order to 1- -717- -986- -7605 or write to: CUSTOMER SERVICE (38- -35) TYCO ELECTRONICS CORPORATION PO BOX 3608 HARRISBURG PA 17105- -3608 A B C SEATING TOOL DIMENSION SEATING TOOL A B C [ ] [ ] [ ] [ ] [ ] [ ] Figure 3 7. REVISION SUMMARY Revisions to this instruction sheet include: S Updated instruction sheet to corporate requirements S Removed references to support anvil S Changed Paragraph 3.2 S Replaced Step 7, added CAUTION, and added NOTE to Section 4 S Removed phone number for customer repair service