9061C

90X1C KISTLER | Alldatasheet

Document overview

• Manufacturer or author: Provided By alldatasheet.com(free datasheet download site)
• PDF pages: 11

Technical content

Piezoelectric force sensors Piezoelectric ring force transducers for tensile and compression forces from 7.5 kN to 1 200 kN 90X1C_003-421e-11.22 © 2020 ... 2022 Kistler Group, Eulachstraße 22, 8408 Winterthur, Switzerland products are protected by various intellectual property rights. For more details visit www.kistler.com. This information corresponds to the current state of knowledge. Kistler reserves the right to make technical changes. Liability for consequential damage resulting from the use of Kistler products is excluded. Types 9001C, 9011C, 9021C, 9031C, 9041C, 9051C, 9061C, 9071C, 9081C, 9091C Piezoelectric force sensors, also known as piezoelectric ring force transducers, for precise measurement of tensile and com- pressive forces in highest resolution.

• Two calibrated measuring ranges
• Linearity including hysteresis ≤±0.5%
• Extremely high stiffness
• Very compact design
• Extremely low threshold
• Degree of protection: IP68, dependent on cable
• No aging, unlimited service life

Description

The 90x1 family is a piezoelectric (PE) sensor series for force measurement in the z-direction. The force to be measured is transferred directly to the quartz sensor element located within through the cover and base of the tightly welded steel case. When subjected to a mechanical load, quartz produces an electric charge that is proportional to that load. An outstanding property of quartz is the very low threshold and, thus, a high sensor sensitivity that remains extremely linear over the entire measuring range. Thus the behaviour in a certain measuring range is practically identical for all PE sensors, independent of their size. This has three unique advantages:

• Overload protection: Even very small forces can be measured with a sensor with a large measuring range.
• High stiffness: To achieve a construction that is as stiff as possible, a larger sensor can also be used without negatively impacting the quality of the measurement signal.
• Grouping: Multiple sensors can simply be added together by electrically connecting them in parallel to a single charge amplifier. The output voltage is then proportional to the sum of all acting forces. Fz Application A rugged design, reliability as well as good repeatability of the measurement values are the primary characteristics of these force sensors. Depending on the size of the force, quasistat- ic measurements can be performed over multiple minutes or hours, whereby the stability of the zero point is heavily depen- dent on the downstream charge amplifier. Dynamic measurements (AC mode, peak-to-peak), on the other hand, can last any length of time. The measuring load washers have a practically unlimited service life Application examples
• Forces in mounting technology
• Forces during spot welding
• Forces in presses
• Force changes in bolted joints under high static preload
• Impact resistance and fatigue strength
• Cutting and forming forces
• Braking and crash forces Type 9001C ... 9071C Type 9081C, 9091C

Piezoelectric force sensors – piezoelectric ring force transducers for tensile and compression forces from 7.5 kN to 1 200 kN, Types 9001C, 9011C, 9021C, 9031C, 9041C, 9051C, 9061C, 9071C, 9081C, 9091C 90X1C_003-421e-11.22 © 2020 ... 2022 Kistler Group, Eulachstraße 22, 8408 Winterthur, Switzerland products are protected by various intellectual property rights. For more details visit www.kistler.com. This information corresponds to the current state of knowledge. Kistler reserves the right to make technical changes. Liability for consequential damage resulting from the use of Kistler products is excluded. Type 9001C 9011C 9021C 9031C 9041C 9051C 9061C 9071C 9081C 9091C Nominal force kN 7.5 15 35 60 90 120 200 400 800 1 200 Calibration preload kN 1.5 3 7 12 18 24 40 80 160 240 Calibrated range 1 kN 0 … 6.0 0 … 12 0 … 28 0 … 48 0 … 72 0 … 96 0 … 160 0 … 320 Calibrated range 3 kN 0 … 800 0 … 1 200 Load limit kN 10.5 21 49 84 126 168 280 560 880 1 320 Linearity incl. hysteresis 1) %FSO ±0.5 ±1 Natural frequency (free-free) 2), calc. kHz ≥170 ≥120 ≥75 ≥53 ≥51 ≥42 ≥32 ≥20 ≥14 ≥9 Maximum bending moment 4) N·m ±5.3 ±15 ±61 ±130 ±244 ±390 ±800 ±2 443 ±5 452 ±13 260 (Mz = 0), calc. Max. sensitivity change Tref = 25°C %/K –0.01 Operating temperature range °C –70 … 200 –40 … 100 Insulation resistance (@23°C) Ω ≥1*1014 ≥1*1013 ≥1*1012 Capacitance pF 14 17 33 52 70 93 149 303 750 890 Connector type KIAG 10-32 neg. Degree of protection (IEC 60529) IP See table, page 9 Sensor material Cover plate 1.4821 1.4460 Coat 1.4542 1.4057 Weight g 3 7 20 36 70 80 157 370 910 2 180 Technical data --> to meet the specifications, the sensors must be operated and counterchecked with 20% preload! 1) Bandwidth relative to the calibrated ranges 2) In the non-mounted state (not preloaded), the natural frequency is reduced by the installation conditions 3) Sensor resistance to shear and bending deformation. (Theoretical) assumption: The sensor is fixed at the bottom side, the shear force acts at the top side, so that the lever length is equal to the total sensor height. 4) With a pretension of 50% of the nominal force

Piezoelectric force sensors – piezoelectric ring force transducers for tensile and compression forces from 7.5 kN to 1 200 kN, Types 9001C, 9011C, 9021C, 9031C, 9041C, 9051C, 9061C, 9071C, 9081C, 9091C 90X1C_003-421e-11.22 © 2020 ... 2022 Kistler Group, Eulachstraße 22, 8408 Winterthur, Switzerland products are protected by various intellectual property rights. For more details visit www.kistler.com. This information corresponds to the current state of knowledge. Kistler reserves the right to make technical changes. Liability for consequential damage resulting from the use of Kistler products is excluded. Fig. 1: Dimensions Type 9001C ... 9071C in mm [in] Dimensions metric [mm]Dimensions Type 9001C … 9071C Dimensions Type 9081C and 9091C Fig. 1: Dimensions Type 9001C … 9071C Fig. 2: Dimensions Type 9081C and 9091C in mm [in] Dimensions metric [mm] Protective sleeve Type d D H s t 9011C 6.5 14.5 8 14.85 7.25 9021C 10.5 22.5 10 18.6 7.25 9031C 13 28.5 11 21.65 7.25 9041C 17 34.5 12 24.65 7.25 9051C 21 40.5 13 27.65 7.25 9061C 26.5 52.5 15 33.65 7.25 9071C 40.5 77.25 17 45 6.75t [t] Dimensions imperial [in] Type d D H s t Dimensions imperial [in] Type d D H s 9081C 40.5 100 22 60.75 9091C 72 145 28 83.25 Type d D H s 9081C 1.59 3.94 0.87 2.39 9091C 2.83 5.71 1.10 3.28

Piezoelectric force sensors – piezoelectric ring force transducers for tensile and compression forces from 7.5 kN to 1 200 kN, Types 9001C, 9011C, 9021C, 9031C, 9041C, 9051C, 9061C, 9071C, 9081C, 9091C 90X1C_003-421e-11.22 © 2020 ... 2022 Kistler Group, Eulachstraße 22, 8408 Winterthur, Switzerland products are protected by various intellectual property rights. For more details visit www.kistler.com. This information corresponds to the current state of knowledge. Kistler reserves the right to make technical changes. Liability for consequential damage resulting from the use of Kistler products is excluded. Pretension Piezoelectric force sensors are always used preloaded in a mounting structure. In general, a preloading force of at least 20% of the nominal force is recommended. The recommend- ed, effective measuring range is thereby achieved and the de- sign-related non-linearities in the lowest load range are elim- inated. Reasons for the pretension:

• Highest level of linearity and stability of the measurement signal.
• Measurement of tensile and compression forces, depending on the size of the pretension (see figure)
• Utilization of the high sensor stiffness for a large frequency range
• Ideal force distribution The pretension must be selected so that the sum of preloading force (Fv) and the process force (±Fz) that arises lies within the measuring range of the sensor at all times (see graphic). Provided it is technologically possible, the average loading of the sensor should be 50% of the nominal force. At this set point, the tolerance with respect to the bending moment is at its greatest (see below, "bending moment"). When pretensioning, the force must be measured with the sensor itself. The sensitivity specified in the technical data is to be used here. The mounting surfaces must be flat, stiff and, if possible, ground. A mounting kit Type 9422A is included in the delivery scope. Sensor mounting Force sensors Type 90x1C must always be mounted on flat, stiff and parallel surfaces under pretension, whereby the force should be uniformly distributed. In order to ensure this for a wide range of applications, Kistler offers an extensive range of mounting accessories. Force transducers/load cells The measuring load washer Types 9001C ... 9071C are also avail- able ready for installation as pre-calibrated force transducers (Types 9301C … 9371C). They are ideal for measuring com- pression and tensile forces; recalibration after mounting is no longer necessary. Calibration and measuring ranges The expected error deviations of a sensor are directly depen- dent on the size of the measuring range and the choice of operating point. The smaller the measuring range the better the linearity and hysteresis. A sensor is typically pretensioned with 20% of the nominal force, which significantly improves the quality of the sensor. Depending on the size, the sensors of the 90x1 series are calibrated in two to three different ranges (see graphic). Measurement directly in the force flux or as force shunt Piezoelectric force sensors are used either directly in the force flux or in the force shunt, embedded in a machine structure. Direct force measurements reach the highest accuracy and resolution, because most of the process force flows through the sensor. Force shunt measurements, on the other hand, load the sen- sors with only a fraction of the process force and reach much higher measurement ranges, though at reduced sensitivity. A detailed instruction manual with further explanations on installation, dimensioning and wiring can be found in the download area of our website www.kistler.com. Fig. 3: Measuring and calibrated ranges

Piezoelectric force sensors – piezoelectric ring force transducers for tensile and compression forces from 7.5 kN to 1 200 kN, Types 9001C, 9011C, 9021C, 9031C, 9041C, 9051C, 9061C, 9071C, 9081C, 9091C 90X1C_003-421e-11.22 © 2020 ... 2022 Kistler Group, Eulachstraße 22, 8408 Winterthur, Switzerland products are protected by various intellectual property rights. For more details visit www.kistler.com. This information corresponds to the current state of knowledge. Kistler reserves the right to make technical changes. Liability for consequential damage resulting from the use of Kistler products is excluded. Bending moment Bending moments M B (Mx + M y) increase the stress on one side of the sensor and decrease it on the other. This results in an uneven distribution of the axial force on the sensor, that can distort the measuring results. In extreme cases, this can lead to a one-sided overload of the sensor or loss of the frictional connection, which can destroy the structure or cause it to slip. It ultimately depends on the applied axial force Fz which of the two cases occurs first in the event of an impermissible bending moment. Maximum possible bending moment Type load limit Fz [kN] max. bending moment MB [N·m] 9001C 7.5 5.3 9011C 15 15 9021C 35 61 9031C 60 130 9041C 90 244 9051C 120 390 9061C 200 800 9071C 400 2 443 9081C 800 5 452 9091C 1 200 13 260 Fig. 4: Bending moment as a function of the axial force Fz Bending moment graph Attention Lateral loads F x,y and/or a torque M z further reduce the measuring range. In case of tight safety margins regarding bending moments and suspected lateral loads or torque, better get in touch with our local sales. Example A force transducer Type 9031C... is preloaded with Fv = 17 kN. What bending moment can be tolerated for process forces in the range Fp = 0 ... 20 kN? We use a normalized formula to calculate the allowable bending moment. Fz is the total axial force on the sensor, so the sum of the preload Fv and the process force Fp. The allowed bending moment depends on the applied total force F z and reaches its peak at 30 kN, half the nominal axial force. In this case, when the process force is at 13 kN (17 kN+13 kN = 30 kN). If the force curve in the process is not known, the lowest value is defined as the maximum load: 72.8 Nm. Fv [%] = 17 kN 60 kN = 28% Fp [%] = 0 kN 60 kN ... 20 kN 60 kN = 0 ... 33% ≙ 72.8 Nm ≙ 101.4 Nm Tensile forces Tensile forces are only applicable as long as the preload is higher than the negative force: they reduce the (pre)load on the sensor, which can be measured accordingly. Fig. 5: maximum bending moment depending on preload and process force

Piezoelectric force sensors – piezoelectric ring force transducers for tensile and compression forces from 7.5 kN to 1 200 kN, Types 9001C, 9011C, 9021C, 9031C, 9041C, 9051C, 9061C, 9071C, 9081C, 9091C 90X1C_003-421e-11.22 © 2020 ... 2022 Kistler Group, Eulachstraße 22, 8408 Winterthur, Switzerland products are protected by various intellectual property rights. For more details visit www.kistler.com. This information corresponds to the current state of knowledge. Kistler reserves the right to make technical changes. Liability for consequential damage resulting from the use of Kistler products is excluded. Preloading set Type 9420Ax1 Preloading set 9420Ax1 can be used to measure compression and tensile forces in an application. The set with centering sleeve (1) and high-strength preloading bolts (2) can handle a pretension of up to 50% and is designed for a minimal force shunt and ideal centering. At the same time, it ensures an op- timum force application. With the included insulating washers (5), the entire sensor can be installed electrically neutral. 3) Washer 4) Hexagonal nut Type 9001C 9011C 9021C 9031C 9041C 9051C 9061C 9071C Preloading set Type 9420A01 9420A11 9420A21 9420A31 9420A41 9420A51 9420A61 9420A71 Fig. 6: Installation of preloading set Type 9420Ax1 Preloading screw Type 9422Ax1 Customers who only measure positive forces in the Fz direction (compression forces) require a lower preload. Ideal for them is set 9422Ax1, consisting of preloading screw (1) and centering clip (2). The screw can be preloaded with up to 30% of the rated range. Further accessories such as insulating washers can be ordered separately if necessary. Type 9001C 9011C 9021C 9031C 9041C 9051C 9061C 9071C Preloading set Type 9422A01 9422A11 9422A21 9422A31 9422A41 9422A51 – – Force shunt % ≈7 ≈8 ≈9 ≈9 ≈9 ≈9 Fig. 7: Installation of preloading screw Type 9422Ax1 Fig. 8: Installation of preloading set Type 9455S/9456S Preloading sets Type 9455S and Type 9456S With the preloading elements of Type 9455S and 9456S, a preloading force of up to 730 kN can be achieved without any specialized. Type 9081C 9091C Preloading set Type 9455S 9456S Force shunt % ≈9 ≈9 Thread M40x2.0 M64x3.0 L Einbau Vorspannschraube 9422Ax1 L Einbau Vorspannsatz 9420Ax1 D H Einbau Druckverteilring 95x5 D H Einbau Druckkappe 95x9 D H Einbau Kugelscheibe 95x3 Kombinierte Bilder mit Renderings und Illustrations KIWAG-SWX_A3q / Vers. 21-Sep-2017 Das Urheberrecht an dieser Zeichnung, die dem Empfänger persönlich anvertraut wird, verbleibt unserer Firma. Ohne unsere schriftliche Genehmigung darf die Zeichnung weder kopiert noch vervielfältigt, noch an Drittpersonen mitgeteilt oder zugänglich gemacht werden. öffentlich siehe Tabelle D-00036-C1 90x1C Bl. Ver. Material-Nr. Zeichnungs-Nr. 100.315.045 Wsa26.07.2018 ges. gepr. gez. 30.08.2018100023119-06 Kopie DatumErsatz für MassstabDatumÄnderung Werkstoff Erste Proj.-Nr. Erstmals verwendet measure. analyze. innovate. 1:1 2 / 2 1A3 TechDoc; Illustration 90x1C, 9420Ax1, 9422Ax1, 945x, 95x5, 95x9, 95x3 1K PE-Kraftsensor L Einbau Vorspannschraube 9422Ax1 L Einbau Vorspannsatz 9420Ax1 D H Einbau Druckverteilring 95x5 D H Einbau Druckkappe 95x9 D H Einbau Kugelscheibe 95x3 Kombinierte Bilder mit Renderings und Illustrations KIWAG-SWX_A3q / Vers. 21-Sep-2017 Das Urheberrecht an dieser Zeichnung, die dem Empfänger persönlich anvertraut wird, verbleibt unserer Firma. Ohne unsere schriftliche Genehmigung darf die Zeichnung weder kopiert noch vervielfältigt, noch an Drittpersonen mitgeteilt oder zugänglich gemacht werden. öffentlich siehe Tabelle D-00036-C1 90x1C Bl. Ver. Material-Nr. Zeichnungs-Nr. 100.315.045 Wsa26.07.2018 ges. gepr. gez. 30.08.2018100023119-06 Kopie DatumErsatz für MassstabDatumÄnderung Werkstoff Erste Proj.-Nr. Erstmals verwendet measure. analyze. innovate. 1:1 2 / 2 1A3 TechDoc; Illustration 90x1C, 9420Ax1, 9422Ax1, 945x, 95x5, 95x9, 95x3 1K PE-Kraftsensor Einbau Vorspannsatz 9456 Kombinierte Bilder mit Renderings und Illustrations KIWAG-SWX_A3q / Vers. 21-Sep-2017 Das Urheberrecht an dieser Zeichnung, die dem Empfänger persönlich anvertraut wird, verbleibt unserer Firma. Ohne unsere schriftliche Genehmigung darf die Zeichnung weder kopiert noch vervielfältigt, noch an Drittpersonen mitgeteilt oder zugänglich gemacht werden. öffentlich 30.01.2019 siehe Tabelle D-00036-C1 90x1C Bl. Ver. Material-Nr. Zeichnungs-Nr. 100.315.04530.01.2019 Kk 30.01.2019 Kk Wsa26.07.2018 ges. gepr. gez. 30.08.2018100012234-34 Kopie DatumErsatz für MassstabDatumÄnderung Werkstoff Erste Proj.-Nr. Erstmals verwendet measure. analyze. innovate. 1:1 3 / 3 aA3 TechDoc; Illustration 90x1C, 9420Ax1, 9422Ax1, 945x, 95x5, 95x9, 95x3 1K PE-Kraftsensor 100.315.045 - a - skbvdg - SKB VDok Grafik - öffentlich - Freigegeben --- siehe Tabelle --- 14-Feb-2019 07:21 (CET) - Kk@int.kistler.com

Piezoelectric force sensors – piezoelectric ring force transducers for tensile and compression forces from 7.5 kN to 1 200 kN, Types 9001C, 9011C, 9021C, 9031C, 9041C, 9051C, 9061C, 9071C, 9081C, 9091C 90X1C_003-421e-11.22 © 2020 ... 2022 Kistler Group, Eulachstraße 22, 8408 Winterthur, Switzerland products are protected by various intellectual property rights. For more details visit www.kistler.com. This information corresponds to the current state of knowledge. Kistler reserves the right to make technical changes. Liability for consequential damage resulting from the use of Kistler products is excluded. Accessories Force distributing ring Type 95x5 The contact surfaces must be just as flat and stiff as the contact surfaces of the sensor itself. If they cannot be finished, local overstressing and damage to the sensor surface must be pre- vented through the use of a force distributing ring (1). Fig. 9: Installation of force distributing ring Type 95x5 Force distributing cap Type 95x9 The force to be measured must be distributed evenly on the contact surface of the force transducer. If a concentrated ap- plication of force cannot be avoided, a force distributing cap (1) compatible with the sensor ensures an ideal distribution of force. 2) Centering pin 3) Allen screw Fig. 10: Installation of force distributing cap Type 95x9 Type 9001C 9011C 9021C 9031C 9041C 9051C 9061C 9071C Force distributing ring Type 9505 9515 9525 9535 9545 9555 9565 9575 D mm 10 14 22 28 34 40 52 75 H mm 6 8 10 11 12 13 15 17 Type 9001C 9011C 9021C 9031C 9041C 9051C 9061C 9071C Force distributing cap Type 9509 9519 9529 9539 9549 9559 9569 9579 D mm 10 14 22 28 34 40 52 75 H mm 10 15 20 25 30 40 50 60 L Einbau Vorspannschraube 9422Ax1 L Einbau Vorspannsatz 9420Ax1 D H Einbau Druckverteilring 95x5 D H Einbau Druckkappe 95x9 D H Einbau Kugelscheibe 95x3 Kombinierte Bilder mit Renderings und Illustrations KIWAG-SWX_A3q / Vers. 21-Sep-2017 Das Urheberrecht an dieser Zeichnung, die dem Empfänger persönlich anvertraut wird, verbleibt unserer Firma. Ohne unsere schriftliche Genehmigung darf die Zeichnung weder kopiert noch vervielfältigt, noch an Drittpersonen mitgeteilt oder zugänglich gemacht werden. öffentlich siehe Tabelle D-00036-C1 90x1C Bl. Ver. Material-Nr. Zeichnungs-Nr. 100.315.045 Wsa26.07.2018 ges. gepr. gez. 30.08.2018100023119-06 Kopie DatumErsatz für MassstabDatumÄnderung Werkstoff Erste Proj.-Nr. Erstmals verwendet measure. analyze. innovate. 1:1 2 / 2 1A3 TechDoc; Illustration 90x1C, 9420Ax1, 9422Ax1, 945x, 95x5, 95x9, 95x3 1K PE-Kraftsensor L Einbau Vorspannschraube 9422Ax1 L Einbau Vorspannsatz 9420Ax1 D H Einbau Druckverteilring 95x5 D H Einbau Druckkappe 95x9 D H Einbau Kugelscheibe 95x3 Kombinierte Bilder mit Renderings und Illustrations KIWAG-SWX_A3q / Vers. 21-Sep-2017 Das Urheberrecht an dieser Zeichnung, die dem Empfänger persönlich anvertraut wird, verbleibt unserer Firma. Ohne unsere schriftliche Genehmigung darf die Zeichnung weder kopiert noch vervielfältigt, noch an Drittpersonen mitgeteilt oder zugänglich gemacht werden. öffentlich siehe Tabelle D-00036-C1 90x1C Bl. Ver. Material-Nr. Zeichnungs-Nr. 100.315.045 Wsa26.07.2018 ges. gepr. gez. 30.08.2018100023119-06 Kopie DatumErsatz für MassstabDatumÄnderung Werkstoff Erste Proj.-Nr. Erstmals verwendet measure. analyze. innovate. 1:1 2 / 2 1A3 TechDoc; Illustration 90x1C, 9420Ax1, 9422Ax1, 945x, 95x5, 95x9, 95x3 1K PE-Kraftsensor

Piezoelectric force sensors – piezoelectric ring force transducers for tensile and compression forces from 7.5 kN to 1 200 kN, Types 9001C, 9011C, 9021C, 9031C, 9041C, 9051C, 9061C, 9071C, 9081C, 9091C 90X1C_003-421e-11.22 © 2020 ... 2022 Kistler Group, Eulachstraße 22, 8408 Winterthur, Switzerland products are protected by various intellectual property rights. For more details visit www.kistler.com. This information corresponds to the current state of knowledge. Kistler reserves the right to make technical changes. Liability for consequential damage resulting from the use of Kistler products is excluded. Spherical washer Type 95x3 If the surfaces cannot be made perfectly parallel, a spherical washer (1) must be used to compensate for this. A finished, even contact surface is still required, however. H* = height at 0° parallelism Fig. 11: Installation of spherical washer Type 95x3 Insulating washers Type 95x7 In case of interference due to ground loops or an electrical potential that differs between the measurement object and the amplifier, the sensor must be installed insulated. The insulating washer sets ensure a clean potential separation. In order to function correctly, the insulating washers should only be used once, and only on finished contact surfaces. Attention These insulating washers with collar can only be used where there are no built-in, continuous centering bushes. Fig. 12: Insulating washers Type 95x7 Type 9001C 9011C 9021C 9031C 9041C 9051C 9061C 9071C Spherical washer Type - 9513 9523 9533 9543 9553 9563 9573 D mm 12 21 24 30 36 52 75 H mm 4 6 7 8 10 14 20 Type 9001C 9011C 9021C 9031C 9041C 9051C 9061C 9071C Insulating washer Type – 9517 9527 9537 9547 9557 9567 9577 D mm 14 22 28 34 40 52 75 H mm 1.125 H in 0.0049 L Einbau Vorspannschraube 9422Ax1 L Einbau Vorspannsatz 9420Ax1 D H Einbau Druckverteilring 95x5 D H Einbau Druckkappe 95x9 D H Einbau Kugelscheibe 95x3 Kombinierte Bilder mit Renderings und Illustrations KIWAG-SWX_A3q / Vers. 21-Sep-2017 Das Urheberrecht an dieser Zeichnung, die dem Empfänger persönlich anvertraut wird, verbleibt unserer Firma. Ohne unsere schriftliche Genehmigung darf die Zeichnung weder kopiert noch vervielfältigt, noch an Drittpersonen mitgeteilt oder zugänglich gemacht werden. öffentlich siehe Tabelle D-00036-C1 90x1C Bl. Ver. Material-Nr. Zeichnungs-Nr. 100.315.045 Wsa26.07.2018 ges. gepr. gez. 30.08.2018100023119-06 Kopie DatumErsatz für MassstabDatumÄnderung Werkstoff Erste Proj.-Nr. Erstmals verwendet measure. analyze. innovate. 1:1 2 / 2 1A3 TechDoc; Illustration 90x1C, 9420Ax1, 9422Ax1, 945x, 95x5, 95x9, 95x3 1K PE-Kraftsensor

Piezoelectric force sensors – piezoelectric ring force transducers for tensile and compression forces from 7.5 kN to 1 200 kN, Types 9001C, 9011C, 9021C, 9031C, 9041C, 9051C, 9061C, 9071C, 9081C, 9091C 90X1C_003-421e-11.22 © 2020 ... 2022 Kistler Group, Eulachstraße 22, 8408 Winterthur, Switzerland products are protected by various intellectual property rights. For more details visit www.kistler.com. This information corresponds to the current state of knowledge. Kistler reserves the right to make technical changes. Liability for consequential damage resulting from the use of Kistler products is excluded. Measuring chain Measure Connect Amplify Connecting cable All sensors of 9001...9091 feature a KIAG 10-32 neg. connec- tion and are compatible accordingly with all KIAG 10-32 pos. cable connectors. Only high-insulation coaxial cables with low capacitance that produce only a very small amount of static electricity may be used as connecting cables for piezoelectric sensors. Kistler uses cables made of high-quality PFA or oil- proof FPM here. On the sensor side, the IP protection class acc. to EN60529 is generally dependent on the used connector. For IP65, the standard 10-32 KIAG cable connector with knurled nut is used; for increased requirements in harsh environments, the industrial-suited 10-32 KIAG pos. int. version is used which, if necessary, can be tightly welded with the sensor case and IP68 achieved. Fig. 13: Measuring chain Compatibilities of cables and charge amplifiers

Piezoelectric force sensors – piezoelectric ring force transducers for tensile and compression forces from 7.5 kN to 1 200 kN, Types 9001C, 9011C, 9021C, 9031C, 9041C, 9051C, 9061C, 9071C, 9081C, 9091C 90X1C_003-421e-11.22 © 2020 ... 2022 Kistler Group, Eulachstraße 22, 8408 Winterthur, Switzerland products are protected by various intellectual property rights. For more details visit www.kistler.com. This information corresponds to the current state of knowledge. Kistler reserves the right to make technical changes. Liability for consequential damage resulting from the use of Kistler products is excluded. Charge amplifiers Various criteria are decisive when selecting the right charge amplifier for a given application. Among the most important are the number of channels, the measuring range, the type of measurement and the frequency range. At this point, only a tabular summary is shown to provide an overview. More de- tailed information and explanations are available in the force product catalog and in the respective data sheets at www. kistler.com. Digital laboratory amplifiers: LabAmp The latest generation of universal laboratory charge amplifi- ers; with integrated data acquisition for dynamic or quasistatic measurements; network ready with web interface. Analog laboratory amplifiers: Type 5015A, 5018A and 5080A The proven analog charge amplifiers for laboratories and re- search. With very wide measuring range and high flexibility (Type 5080A). Industrial amplifiers Size- and function-optimized amplifiers for continuous use in daily work. Bus-capable; some with further functions. (evalua- tion of force curves, etc.) Fig. 14: LabAmp Type 5165A and Type 5167A Fig. 15: Laboratory charge amplifiers Type 5015A and Type 5080A Fig. 16: Industrial amplifiers Type 5073A and 5074A (from left) At the right is the maXYmos BL Type 5867B…

Piezoelectric force sensors – piezoelectric ring force transducers for tensile and compression forces from 7.5 kN to 1 200 kN, Types 9001C, 9011C, 9021C, 9031C, 9041C, 9051C, 9061C, 9071C, 9081C, 9091C 90X1C_003-421e-11.22 © 2020 ... 2022 Kistler Group, Eulachstraße 22, 8408 Winterthur, Switzerland products are protected by various intellectual property rights. For more details visit www.kistler.com. This information corresponds to the current state of knowledge. Kistler reserves the right to make technical changes. Liability for consequential damage resulting from the use of Kistler products is excluded. Included accessories Type

• Special grease 1063
• Preloading screw for preloads for 9422A01 compression force measurement, … including centering sleeve (only with 9422A51 sensors Type 9001C ... 9051C) Optional accessories
• Preloading element for preloads for 9420A01 pressure and tensile force measurement, ... including mounting accessories 9420A71
• Preloading element for big force sensors 9455S, 9456S Type 9081 and 9091 Mounting accessories (optional)
• Force distributing ring for piezoelectric 95x5 force sensor
• Spherical washer for piezoelectric 95x3 force sensor
• Insulating washer for piezoelectric 95x7 force sensor
• Force distributing cap for piezoelectric 95x9 force sensor Cables (optional)
• Connection and extension cables according data sheet for cables for force and torque sensors Piezoelectric force sensor Range 0 … 7.5 kN 01 Range 0 … 15 kN 11 Range 0 … 35 kN 21 Range 0 … 60 kN 31 Range 0 … 90 kN 41 Range 0 … 120 kN 51 Range 0 … 200 kN 61 Range 0 … 400 kN 71 Range 0 … 800 kN 81 Range 0 … 1 200 kN 91 Ordering key Type 90 C