90384-1 MACOM | Alldatasheet
Document overview
- Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
- PDF pages: 4
Technical content
AMP Hand Crimping Tool 90384-1 408-6510 SS 4.2. Periodic Inspection Position Point on Center of A. Lubrication Wire Barrel Oa tae (CY Lubricate all pins, pivot points, and bearing surfaces Seam y] with SAE 20 motor oil as follows: \\ Tool used in daily production—lubricate daily Y tI L Tool used daily (occasional)—lubricate weekly Il] Tool used weekly—lubricate monthly . L—- Modified Crimp Height Wipe excess oil from tool, particularly from crimping Anwil 2,8440.08 area. Oil transferred from the crimping area onto [112.003] certain terminations may affect the electrical characteristics of an application. Figure 4 B. Visual Inspection D. CERTI-CRIMP Ratchet Inspection | The CERTI-CRIMP ratchet feature on AMP hand 1. Close tool handles until ratchet releases and tools should be checked to ensure that the ratchet then allow them to open freely. If they do notopen —_—_ggag not release prematurely, allowing the crimping quickly and fully, the spring is defective and must dies to open before they have fully bottomed. Obtain be replaced. See Section 5, REPLACEMENT AND a 0.025 [.001] shim that is suitable for checking the REPAIR. clearance between the bottoming surfaces of the crimping dies. Proceed as follows: 2. Inspect head assembly for worn, cracked, or . broken dies. If damage is evident, return the tool to 1. Select a contact and wire for the tool. AMP for evaluation and repair. See Section 5, 2. Position the contact and wire between the REPLACEMENT AND REPAIR. crimping dies, as described in Section 3, CRIMPING PROCEDURE. C. Crimp Height Inspection 3. Holding wire in place, squeeze the handles until the CERTI-CRIMP ratchet releases. Hold the This inspection requires the use of a modified handles in this position, maintaining just enough micrometer with a modified anvil and spindle, as tension to keep the dies closed. shown in Figure 4. AMP recommends the Crimp 3. Check the clearance between the bottomin Height Comparator RS—1019-SLP which can be surfaces of the crimping dies. If the clearance is purchased from: 0.028 [.001] or lass, the ratchet is satisfactory. If Sh Industrial Supply C vatco clearance exceeds 0.025 [.001], the ratchet is out wearer Inaustria! Supply Co. of adjustment and must be repaired. See Section
20 North Penn Street 1410 St d DI
Yor PA 701-1014 Bethlehem, PA 18017-2527 5, REPLACEMENT AND REPAIR. Proceed as follows: 5. REPLACEMENT AND REPAIR . oo. The parts listed in Figure 5 are customer— 1. Select a contact and wire for the crimping replaceable. A complete inventory can be stocked chamber. and controlled to prevent lost time when replacement . of parts is necessary. Parts other than those listed 2. Refer to Section 3, CRIMPING PROCEDURE, should be replaced by AMP to ensure quality and and crimp the contact accordingly. reliability of the tool. Order replacement parts through . | | your AMP representative, or call 1-800-526-5142, or 3. Using the crimp height comparator, measure the —_send a facsimile of your purchase order to wire barrel crimp height as shown in Figure 4. Ifthe 717-986-7605, or write to: crimp height conforms to that height, the tool is considered dimensionally correct. If not, the tool OE Roo ewes (38-35) must be returned to AMP for evaluation and repair. PO. BOX 3608 See Section 5, REPLACEMENT AND REPAIR. ae ee section Sy HARRISBURG, PA 17105-3608 For additional information concerning the use of the Tools may also be returned to AMP for evaluation and crimp height comparator, refer to AMP instruction repair. For tool repair service, contact an AMP sheet 408-7424. representative at: 1-800-526-5136. Rn ee Rev B 30f4
AMP Hand Crimping Tool 90384-1 408-6510 SS oR Ss mx: —— ws = . . cS SRO (Closed) 25.4 [1.00] a 2 = = 2: eee Fl es = = —— 312 SY [12.25] Weight: 936 g [2 lb, 1 oz] CUSTOMER REPLACEMENT PARTS ITEM PART NUMBER DESCRIPTION QTY PER TOOL 1 21045-3 RING, Retaining 4 2 2
4 PIN, Retaining 1
- REVISION SUMMARY The following changes were made since the previous release of this sheet: Per EC 0990-0725-99 * Changed tool repair service information in Section 5, REPLACEMENT AND REPAIR Updated document format Rn ee 4ot4 Rev B