84PR10KLFTR_12 BITECH | Alldatasheet

Document overview

  • Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
  • PDF pages: 3

Technical content

Standard Resistance Range, Ohms 10 to 1Meg Standard Resistance Tolerance ±10% Input Voltage, Maximum 200 Vdc or rms not to exceed power rating Slider Current, Maximum 100mA or within rated power, whichever is less Power Rating, Watts 0.25 at 85°C derating to 0 at 150°C End Resistance, Maximum 2 Ohms Actual Electrical Travel, Turns, Nominal 12 Dielectric Strength 900 Vrms Insulation Resistance, Minimum 1,000 Megohms Resolution Essentially infinite Contact Resistance Variation, Maximum 1% or 1 Ohms, whichever is greater ENVIRONMENTAL Seal 85°C Fluorinert® (No Leaks) Temperature Coefficient, Maximum ±100ppm/°C (<100 Ohms = ±250ppm/°C) Operating Temperature Range –65°C to +150°C Thermal Shock 5 cycles, –65°C to +150°C (1% ∆RT, 1% ∆VR) Moisture Resistance Ten 24 hour cycles (1% ∆RT, IR 100 Megohms Min.) Shock, 6ms Sawtooth 100G’s (1% ∆RT, 1% ∆VR) Vibration 20G’s, 10 to 2,000 Hz (1% ∆RT, 1% ∆VR) High Temperature Exposure 250 hours at 150°C (2% ∆RT, 2% ∆VR) Rotational Life 200 cycles (3% ∆RT) Load Life at 0.25 Watts 1,000 hours at 85°C (2% ∆RT) Resistance to Solder Heat 260°C for 10 sec. (1% ∆RT) Temperature Exposure, Maximum 215°C for 3 min. (1% ∆RT) MECHANICAL Mechanical Stops Clutch action, both ends Torque, Starting Maximum 3 oz.-in. (0.021 N-m) Weight, Nominal .014 oz. (.40 grams) MODEL 84 1/4” Square Multiturn Surface Mount Cermet Trimming Potentiometer Fluorinert® is a registered trademark of 3M Company. Specifications subject to change without notice.

SIDE ADJUSTMENT (Inch/mm) Standard Marking On This Surface .100 2.54 .100 2.54 .100 2.54 .100 2.54 .040 ± .015 1.02 ± 0.38 .210 ± .015 5.33 ± 0.38 .250 ± .020 6.35 ± 0.51 .040 ± .010 1.02 ± 0.25 3x .105 ± .015 2.67 ± 0.38 3x Recommend PCB Layout - Model 84P .125 ± .015 3.18 ± 0.38 3x .040 ± .015 1.02 ± 0.38 .375 ± .015 9.53 ± 0.13 CL (2) (3) (1) (3) (1) (2) (1) (2) (3) Model 84P Model 841-74 TOP ADJUSTMENT (Inch/mm) Housing: Molded Plastic Terminal Pins: Solderable Metal Adjustment Screw Standard Marking On This Surface Min. With .005 0.13 Min. Wide x.020 0.51 Min. Depth.020 0.51 .100 2.54 .100 2.54 .070 ± .015 1.78 ± 0.38 .295 ± .015 7.49 ± 0.38 .040 ± .015 1.02 ± 0.38 .250 ± .020 6.35 ± 0.51 .050 ± .010 1.27 ± 0.25 .040 ± .010 1.02 ± 0.25 .170 ± .015 4.32 ± 0.38 .070 ± .005 1.78 ± 0.13 3x .040 ± .015 1.02 ± 0.38 3x .018 ± .002 0.46 ± .051 CL CL (1) (2) (3) Model 84W SIDE ADJUSTMENT (Inch/mm) .100 2.54 .100 2.54 3x .040 ± .015 1.02 ± 0.38 .100 2.54 .100 2.54 3x .040 ± .015 1.02 ± 0.38 Recommended PCB Layout - Models 84W and 84X .110 ± .015 2.80 ± 0.38 .295 ± .005 7.49 ± 0.13 CL .050 ± .010 1.27 ± 0.25 (1) (2) (3) ~Standard Marking On This Surface .040 ± .010 1.02 ± 0.25 (2) (1) (3) Model 84X Note: Model 84W dimensions applicable to all models except as noted.

ORDERING INFORMATION

84 P R 10K LF TR

Packaging Option: TR = Tape & Reel (No code used for tubes) RoHS Compliant Product Code - Optional Resistance Value Standard: Standard: Tubes All units oriented with #1 pin to same side. Pin Style P W/X Magazine Width = 0.47”(11.93mm) 0.37”(9.39mm) Height = 0.32”(8.13mm) 0.47”(11.93mm) Length = 14.5”(368mm) 14.5”(368mm) 16.5”(429mm) Capacity = 50 Units 50 Units Option: Embossed Tape & Reel (84P & 84W only) All units oriented with #1 pin to the right of the direction of feed. Pin Style = P W/X Tape Width = 16 mm 24mm Sprocket = 4 mm pitch 4mm pitch Capacity = 500 Units 400 Units Reel Diameter = 13” (330 mm) 13” (330mm) CIRCUIT DIAGRAM (1) (2) (3) CW NOTES mm INCH Metric equivalents, based on 1 inch = 25.4mm are rounded to the same number of significant figures as in the original English units and are provided for general information only. Tolerances unless otherwise specified: Linear = ± .01 inches (.25mm) Angular = ± 2 degrees STANDARD RESISTANCE VALUES, OHMS 10 100 1K 10K 50K 250K 20 200 2K 20K 100K 500K 50 500 5K 25K 200K 1Meg