408-9452 MACOM | Alldatasheet
Document overview
- Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
- PDF pages: 2
Technical content
/C0052/C0048/C0056/C0045/C0057/C0052/C0053/C0050/C0069/C0120/C0116/C0114/C0097/C0099/C0116/C0105/C0111/C0110/C0084/C0111/C0111/C0108/C0115/C0056/C0052/C0051/C0052/C0055/C0053/C0045/C0049/C0097/C0110/C0100/C0045/C0050 /C0082/C0101/C0118/C0065/C0050/C0111/C0102 /C0050 /C0084/C0121/C0099/C0111 /C0069/C0108/C0101/C0099/C0116/C0114/C0111/C0110/C0105/C0099/C0115/C0067/C0111/C0114/C0112/C0111/C0114/C0097/C0116/C0105/C0111/C0110 Figure 3 /C0065 /C0066 /C0049/C0050/C0046/C0055/C0048 /C0091/C0046/C0053/C0048/C0048/C0093 /C0049/C0055/C0046/C0055/C0056 /C0091/C0046/C0055/C0048/C0048/C0093 /C0049/C0052/C0052/C0046/C0055/C0056 /C0091/C0053/C0046/C0055/C0048/C0048/C0093 /C0051/C0046/C0056/C0049 /C0091/C0046/C0049/C0053/C0048/C0093 /C0054/C0046/C0051/C0053 /C0091/C0046/C0050/C0053/C0048/C0093 /C0048/C0046/C0053/C0049 /C0091/C0046/C0048/C0050/C0048/C0093 /C0068/C0073/C0077/C0069/C0078/C0083/C0073/C0079/C0078/C0083 /C0065/C0066 /C0056/C0052/C0051/C0052/C0055/C0053/C0045/C0049 /C0053/C0046/C0053/C0057 /C0091/C0046/C0050/C0050/C0048/C0093 /C0048/C0046/C0056/C0052 /C0091/C0046/C0048/C0051/C0051/C0093 /C0056/C0052/C0051/C0052/C0055/C0053/C0045/C0050 /C0049/C0054/C0046/C0053/C0049 /C0091/C0046/C0054/C0053/C0048/C0093 /C0049/C0046/C0053/C0050 /C0091/C0046/C0048/C0054/C0048/C0093 /C0084/C0079/C0079/C0076 /C0080/C0078 /C0051/C0046/C0049/C0046/C0070/C0114/C0111/C0110/C0116/C0082/C0101/C0108/C0101/C0097/C0115/C0101/C0072/C0111/C0117/C0115/C0105/C0110/C0103/C0040/C0056/C0052/C0051/C0052/C0055/C0053/C0045/C0049/C0041 Refer to Figure 1 and proceed as follows: 1. Align extraction tip with locking lance release slot at FRONT of desired contact cavity. 2. Insert tip straight into slot until it bottoms. 3. Hold tool in position and pull back on wire; the contact will come out easily. 4. Remove extraction tool from FRONT of housing. /C0051/C0046/C0050/C0046/C0083/C0105/C0100/C0101/C0082/C0101/C0108/C0101/C0097/C0115/C0101/C0072/C0111/C0117/C0115/C0105/C0110/C0103/C0040/C0056/C0052/C0051/C0052/C0055/C0053/C0045/C0050/C0041 Refer to Figure 2 and proceed as follows: 1. Note that a solid rib extends through the center of the housing. Determine from which half of the housing the contact is accessible. 2. Align extraction tip with appropriate locking lance release slot in side of housing. 3. Insert tip straight into slot until it touches a contact. Note that this could be the first contact in the row – not necessarily the contact to be removed. Make certain tool is perpendicular to the housing. 4. Grip wire of first contact in slot. Apply slight inward pressure on tool to depress contact locking lance and, simultaneously, pull back on wire. The contact will come out easily. 5. Repeat these procedures until designated contact is removed. /C0052/C0046 /C0084/C0079/C0079/C0076/C0073/C0078/C0083/C0080/C0069/C0067/C0084/C0073/C0079/C0078/C0047/C0077/C0065/C0073/C0078/C0084/C0069/C0078/C0065/C0078/C0067/C0069 Extraction Tool 843475–[ ] should conform to the dimensions listed in Figure 3. It is recommended that each tool be inspected upon arrival to be sure it has not been damaged in transit, and at regularly scheduled intervals to be sure it remains functional. Order replacements through your Tyco Electronics Representative, or call 1–800–526–5142, or send a facsimile of your purchase order to 717–986–7605, or if the tool requires repair, send it with a written description of the problem to: CUSTOMER SERVICE (038–035) TYCO ELECTRONICS CORPORATION P .O. BOX 3608 HARRISBURG, PA 17105–3608 /C0053/C0046 /C0082/C0069/C0086/C0073/C0083/C0073/C0079/C0078/C0083/C0085/C0077/C0077/C0065/C0082/C0089 /C0083Updated document to corporate requirements /C0083New format