82PR10KLF BITECH | Alldatasheet
Document overview
- Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
- PDF pages: 4
Technical content
Standard Resistance Range, Ohms 10 to 1Meg Standard Resistance Tolerance ±10% (<100 Ohms = ±20%) Input Voltage, Maximum 200 Vdc or rms not to exceed power rating Slider Current, Maximum 100mA or within rated power, whichever is less Power Rating, Watts 0.5 at 70°C derating to 0 at 125°C End Resistance, Maximum 2 Ohms Actual Electrical Travel, Nominal 220° Dielectric Strength 600 Vrms Insulation Resistance, Minimum 1,000 Megohms Resolution Essentially infinite Contact Resistance Variation, Maximum 1% or 1 Ohm, whichever is greater ENVIRONMENTAL Seal 85°C Fluorinert® (No Leaks) Temperature Coefficient, Maximum ±100ppm/°C Operating Temperature Range –55°C to +125°C Thermal Shock 5 cycles, –55°C to +125°C (1% ∆RT, 1%∆VR) Moisture Resistance Ten 24 hour cycles (1% ∆RT, IR 100 Megohms Min.) Shock, 6ms Sawtooth 100G’s (1% ∆RT, 1% ∆VR ) Vibration 20G’s, 10 to 2,000 Hz (1% ∆RT, 1% ∆VR ) High Temperature Exposure 250 hours at 125°C (2% ∆RT, 2% ∆VR ) Rotational Life 200 cycles (3% ∆RT) Load Life at 0.5 Watts 1,000 hours at 70°C (2% ∆RT) Resistance to Solder Heat 260°C for 10 sec. (1% ∆RT) MECHANICAL Mechanical Stops Solid Torque, Starting Maximum 3 oz.-in. (0.021 N-m) Weight, Nominal .02 oz. (0.60 grams) MODEL 82 1/4” Diameter Single Turn Cermet Trimming Potentiometer Fluorinert® is a registered trademark of 3M Company. Specifications subject to change without notice.
SIDE ADJUSTMENT (Inch/mm) .10 2.54 .10 2.54 .185 ± .015 4.669 ± 0.381 .035 0.889 .10 2.54 .17 4.32 .28 7.11 Case: Plastic Housing: Metal Model No. And Resistance Value marked on this surface .205 ± .015 5.207 ± 0.381 .36 9.14.25 6.35 (3) (2) (1) Min. .012 0.305 Min. (2) (3)(1) .10 2.54 .10 2.54 .10 2.54 .17 4.32 .18 4.57 Min. Model 82M (2) (1) (3) .10 2.5 .10 2.5 .21 5.3 .18 4.57 .020 0.51Min.Min. Standoffs Model 82W 90° ±5° (2) (3)(1) .110 ± .005 2.794 ± 0.127 .025 ± .005 0.635 ± 0.127Long X .035 ± .005 0.889 ± 0.127Wide X Deep Slot .250 ± .015 6.350 ± 0.381 Dia. Terminal Pins (3) Solderable .017 ± .003 0.432 ± 0.076 Dia. .140 3.556 Max. .011 0.28 A Standoffs Housing Metal Min. .10 2.54 .10 2.54 .025 0.635 .25 6.35 Min. .625 15.875 Min. 82P 82PF Model Dim. A TOP ADJUSTMENT (Inch/mm) Model 82P, 82PF Note: Model 82P dimensions applicable to all models except as noted.
Standard: Boxes Capacity = 50 Units (82PA, 82PF) = 100 Units (All other styles) Option: Tubes All units oriented with #1 pin to same side. Pin Style PA P,M,W Magazine Width = 0.28” 0.34” Height = 0.94” 0.65” Length = 15.6” 27.5” Capacity = 50 Units 100 Units Option: Tape & Reel, Ammo Pack (Available for 82W Only) All units oriented with #1 pin to the right of the direction of feed. Seat Plane to Centerline of Sprocket Hole = .71” (18.03 mm) Tape Width = 18 mm Sprocket = Single Hole .50” spacing Capacity = 1,000 Units Reel Diameter = 14” (356 mm) Ammo Tape Fold = 12” (305 mm) Box = 1.5” x 13” x 10” STANDARD RESISTANCE VALUES, OHMS 10 100 1K 10K 50K 250K 20 200 2K 20K 100K 500K 50 500 5K 25K 200K 1Meg
ORDERING INFORMATION
82 P R 10K LF
RoHS Compliant Product Code - Optional Resistance Value Resistance Prefix
82 W R 10K LF TB
Pin Style Packaging Option: TB = Tubes (Pin styles P, PA, M, W) RoHS Compliant Product Code - Optional
82 W F R 10K LF TR
Pin Style Suffix: (Used with AP and TR packaging options. Applicable to pin styles W only. "F" designates 0.60" lead length.) Packaging Option: AP = Ammo pack TR = Tape & Reel (Pin styles W, X only) RoHS Compliant Product Code - Optional Standard: Option: CIRCUIT DIAGRAM (1) (2) (3) CW NOTES mm INCH Metric equivalents, based on 1 inch = 25.4mm are rounded to the same number of significant figures as in the original English units and are provided for general information only. Tolerances unless otherwise specified: Linear = ± .01 inches (.25mm) Angular = ± 2 degrees Option: