8151 BITECH | Alldatasheet

Document overview

  • Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
  • PDF pages: 4

Technical content

BI Technologies Corporation

4200 Bonita Place, Fullerton, CA 92835 USA

Phone: 714 447 2345 Website: www.bitechnologies.com Position Sensor 7/8” D iam eter 10 turn* N on-Contacting H all Effect M odel 8150 8151 1/8” Shaft, 1/4” Bushing 8153 1/8” Shaft, Servo Mount 8154 6 mm shaft, 3/8” Bushing 8156 1/4” shaft, 3/8” Bushing Total Mechanical Travel Up to 3600° continuous Bearing Bushing models use bronze sleeve, Servo model uses two ball bearings Weight 0.7 oz nominal Panel Nut Tightening Torque 25 in. lb. maximum Start/Run Torque (ES option adds 0.5 oz.-in.) < 0.1 oz-in M ODEL STYLES AVAILABLE M ECHANICAL ELECTRICAL 1 1 Specifications subject to change without notice. 2 Linearity is measured per voltage code range, inset by 1% of input voltage on each end. * Model available in 3 & 5 turn versions. February 16 2016 Model 8150 page 1 of 4 Input Voltage 4.5 to 5.5 Vdc nominal Output Voltage 0.2 Vdc (4%) to 4.8 Vdc (96%) Typical (see Feature Codes table) Output Overvoltage Limits 10 Vdc to -0.3 Vdc; output may be shorted to ground or supply without damage Output Current ±15 mA maximum Output Load 1 k Ω Min ., 10 kΩ typical Supply Voltage Absolute Limits 20 Vdc Max., -10 Vdc minimum Independent Linearity 2 ±0.5% (0.25% Available) Hysteresis 10° maximum (10 turn), 5° maximum (5 turn), 3° maximum (3 turn) Resolution 0.88° for 3600° travel, 0.44° for 1800° travel, 0.27° for 1080° travel Supply Current 8.5 mA typical, 12 mA maximum Dielectric Strength 750 V rms Insulation Resistance 1,000 Meg Ω minimum Electrostatic Discharge (ESD) Passes 2 kV human body model and 15 kV air discharge Bulk Current Injection (BCI) Passes 2-500 MHz at 200 mA Actual Electrical Travel Same as mechanical travel Temperature Coefficient of Output Voltage ± 20 ppm/°C RoH S 2 com pliant Pb

BI Technologies Corporation Phone: 714 447 2345 Website: www.bitechnologies.com Operating Temperature Range -40°C to +125°C Shock Per MIL R-39023, 6 ms Saw-tooth 100 G’s Vibration Per MIL R-39023, 10 G’s, 100 to 500 Hz Moisture Resistance, Powered Per MIL 202G, Method 106G Rotational Life 8153: 50 million shaft revolutions with side load < 0.33 lb, 100 million with side load < 0.25 lb all other models: 10 million shaft revolutions with up to 8 oz side load Storage Temperature Range -55°C to +125°C Ingress Protection Rating (IP Code) IP50, IP66 available as option (feature code ES) ENVIRONM ENTAL ORDERING INFORM ATION Model Series Voltage Output Code (see table) Number of turns (3, 5, and 10 are standard) Optional Feature Code (see table) No code required for slotted shaft 8154/8156 or for plain shaft 8151/8153 Linearity, Independent 8150 V1 T10 L.5 XX CODES M odel 8150 Voltage Output Codes V0 ≤ 3% to ≥ 96% V1 4% to 96% V2 5% to 95% V3 10% to 90% V4 15% to 85% V5 20% to 80% Optional Feature Codes no code 8151, 8153 plain shaft. 8154, 8156 slotted shaft SS Slotted Shaft (8151, 8153 only. Not used for 8154, 8156) FS Flatted Shaft LT Linearity Data SL Shaft Lock (8156 only) CW Reverse Direction HT High Torque (8156 only) ES Seal IP66 (8154, 8156 only) February 16 2016 Model 8150 page 2 of 4 When V0 is used the angle specified is the theoretical angle over which the output would vary if the output could actually reach 0% and 100% of Vcc. When multiple feature codes are used the P/N shall be in the same sequence as listed in this table (top to bottom).

BI Technologies Corporation Phone: 714 447 2345 Website: www.bitechnologies.com M odel 8150 OUTLINE DRAW ING (bushing m ounts) February 16 2016 Model 8150 page 3 of 4 M ATCHING TURNS COUNTING DIALS 8151: RBJ, 2601, 2641 8154, 8156: RB, 2126, 2606, 2606S, 2607, 2607S, 2626, 2627, 2646, 2646S, 2647, 2647S

BI Technologies Corporation Phone: 714 447 2345 Website: www.bitechnologies.com M odel 8150 OUTLINE DRAW ING (8153 servo m ount) February 16 2016 Model 8150 page 4 of 4