DATASHEET SEARCH SITE | WWW.ALLDATASHEET.COM

Document overview

  • Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
  • PDF pages: 6

Technical content

936.4888/b Subject to alteration. 4-Port Antenna Frequency Range Dual Polarization HPBW Adjust. Electr. DT set by hand or by optional RCU (Remote Control Unit) 1710–2180790–960 XX 90°90° 0°–6°0.5°–7 B1B1R1R1 Type No. 80010123V03 Lowband R1, connector 1–2R1, connector 1–2 790–960 Frequency range MHz 790 – 862 824 – 894 880 – 960 Polarization ° +45, –45 +45, –45 +45, –45 Average gain Tilt dBi Horizontal Pattern: Half-power beam width ° 86 86 86 Front-to-back ratio, copolar dB > 25 > 25 > 25 Cross polar ratio Maindirection 0° Sector ±60° ±60° dB Typically: > 10 avg. 16 T ypically: > 10 avg. 16 T ypically: > 13 avg. 19 T racking, Avg. dB 0.5 Squint ° ±3.0 Vertical Pattern: Half-power beam width ° 7.3 7.2 6.9 Electrical tilt ° 0.5–7, continuously adjustable Min. sidelobe supression for fi rst sidelobe above main beam dB VSWR < 1.5 Isolation: Intrasystem dB > 30 Isolation: Intersystem dB > 42 (790–960 // 1710–2180 MHz) Intermodulation IM3 dBc < –150 (2 x 43 dBm carrier) Max. power per input Total power W 500 (at 50 °C ambient temperature) 1000 (at 50 °C ambient temperature) Kathrein USA Greenway Plaza II, 2400 Lakeside Blvd., Suite 650, Richardson TX 75082 All specifications are subject to change without notice. The latest specifications are available at www.kathreinusa.com

Mechanical specifi cations Input 4 x 7-16 female (long neck) Connector position Bottom Adjustment Mechanism 2x, Position bottom continuously adjustable Wind load (at Rated Wind Speed: 150 km/h) N | lbf Frontal: 680 | 153 Maximal: 750 | 169 Max. wind velocity km/h mph 200 124 Height / width / depth mm inches 2635 / 262 / 149 103.7 / 10.3 / 5.9 Category of mounting hardware H (Heavy) Weight kg lb 33.0 / 35.0 (clamps incl.) 72.8 / 77.2 (clamps incl.) Packing size mm inches 2966 x 282 x 182 116.8 x 11.1 x 7.2 Scope of Supply Panel and 2 units of clamps for 42–115 mm | 1.7–4.5 inches diameter Page 2 of 3 80010123V03 936.4888/b Subject to alteration. 4-Port Antenna Highband B1, connector 3–4B1, connector 3–4 1710–2180 Frequency range MHz 1710 – 1880 1850 – 1990 1920 – 2180 Polarization ° +45, –45 +45, –45 +45, –45 Average gain Tilt dBi Horizontal Pattern: Half-power beam width ° 84 85 88 Front-to-back ratio (180°±30°) dB > 23 > 23 > 23 Cross polar ratio Maindirection 0° Sector ±60° ±60° dB Typically: > 10 avg. 16 T ypically: > 12 avg. 17 T ypically: > 10 avg. 18 T racking, Avg. dB 0.5 Squint ° ±3.0 Vertical Pattern: Half-power beam width ° 4.8 4.5 4.2 Electrical tilt ° 0–6, continuously adjustable Min. sidelobe supression for fi rst sidelobe above main beam dB VSWR < 1.5 Isolation: Intrasystem dB > 30 Isolation: Intersystem dB > 42 (790–960 // 1710–2180 MHz) Intermodulation IM3 dBc < –150 (2 x 43 dBm carrier) Max. power per input Total power W 250 (at 50 °C ambient temperature) 500 (at 50 °C ambient temperature) Correlation Table Frequency range Array Connector 790– 960 MHz R1 1–2 1710–2180 MHz B1 3–4 Kathrein USA Greenway Plaza II, 2400 Lakeside Blvd., Suite 650, Richardson TX 75082 All specifications are subject to change without notice. The latest specifications are available at www.kathreinusa.com

936.4888/b Subject to alteration. Accessories General Information For downtilt mounting use the clamps for an appropriate mast diameter together with the downtilt kit. Wall mounting: No additional mounting kit needed. Material: Refl ector screen: Weather-proof aluminum. Fiberglass housing: It covers totally the internal antenna components. The special design reduces the sealing areas to a minimum and guarantees the best weather protection. Fiberglass material guarantees optimum performance with regards to stability, stiffness, UV resistance and painting. The color of the radome is light grey. All screws and nuts: Stainless steel. Grounding: The metal parts of the antenna including the mounting kit and the inner conductors are DC grounded. Layout of interface: 50 | 2.0 103 | 4.1 180 | 7.1 262 | 10.3 * Bottom view * Dimensions refer to radome All dimensions in mm | inches 45 | 1.8 88 | 3.5 167 | 6.6 * 149 | 5.9 * 106 | 4.2 RCU 790–960 RCU 1710–2180 –45° 790–960 –45° 1710–2180 +45° 1710–2180 +45° 790–960 long neck4) 2635 | 103.7 2677 | 105.4 2717 | 107.0 2835 | 111.6 Adjustment mechanism with integrated scale 1) ’ 9 | 0.4 2) 72 | 2.8 3) 64 | 2.5 4) 35 –42 | 1.4–1.7 All dimensions in mm | inches Accessories (order separately if required) Type No. Description Remarks mm | inches Weight approx. kg | lb Units per antenna 731651 1 clamp Mast diameter: 28 – 60 | 1.1 – 2.4 0.8 | 1.8 2 85010002 1 clamp Mast diameter: 110 – 220 | 4.3 – 8.7 2.7 | 6.0 2 85010003 1 clamp Mast diameter: 210 – 380 | 8.3 – 15.0 4.8 | 10.6 2 85010008 1 downtilt kit Downtilt angle: 0° – 8° 4.3 | 9.5 1 Accessories (included in the scope of supply) 738546 1 clamp Mast diameter: 42 – 115 | 1.7 – 4.5 1.1 | 2.4 2 Kathrein USA Greenway Plaza II, 2400 Lakeside Blvd., Suite 650, Richardson TX 75082 All specifications are subject to change without notice. The latest specifications are available at www.kathreinusa.com

738546 Page 1 of 1

Clamp Included in the Scope of Supply 936.3920/c Subject to alteration. Suitable for mast diameter (mm) [inches] 42 – 115 [1.65 – 4.53] Antenna – mast distance (mm) [inches] 20 – 25 [0.79 – 0.98] Material of clamp and screws Hot-dip galvanized steel / stainless steel Weight (kg) [lb] 1.1 [2.43] Please note: Kathrein does not recommend to use counter nuts. The additional nuts supplied are only meant as spares. All dimensions in mm and [inches] 152 [5.98] 100 [3.94] 40 [1.57] 72 [2.83] 35 [1.38] 64 [2.52] 125 [4.92] 40 [1.57] 20–25 [0.79–0.98] ’ 42–115 [1.65–4.53] M10 ‰MA = 25 Nm M8 ‰MA = 20 Nm 20–25 [0.79–0.98] Kathrein USA Greenway Plaza II, 2400 Lakeside Blvd., Suite 650, Richardson TX 75082 All specifications are subject to change without notice. The latest specifications are available at www.kathreinusa.com

936.4037/a Subject to alteration. General Instructions for Adjustment Mechanism Description of the adjustment mechanism (protective cap removed): Manual adjustment procedure: Optional: RCU (Remote Control Unit) for remote-controlled downtilt adjustment: For a description of RCU installation please refer to the respective data sheet. Remove the protective cap and the twist protection completely. ➀ Twist protection. ➁ Downtilt spindle with integrated scale. ➀ Thread for fi xing the pro tective cap or the RCU (Remote Control Unit). ➁ Gearwheel for RCU power drive. To set the downtilt angle exactly, you must look horizontally at the scale. The lower edge of the gear- wheel must be used for alignment. Set downtilt angle by rotating the gearwheel. Screw on the twist protection and the protective cap again. 0° – max.° 0° – max.° Kathrein USA Greenway Plaza II, 2400 Lakeside Blvd., Suite 650, Richardson TX 75082 All specifications are subject to change without notice. The latest specifications are available at www.kathreinusa.com

936.4037/a Subject to alteration. Installation of the feederline connector and RCU (optional): In order to protect the adjustment mechanism, the protective caps have to be attached during feederline installation! Carefully place the connector and fi x the nut using a torque-wrench (according to the manufacturers guidelines). After feederline installation, the optional remote control units (RCUs) can be mounted. These tools are suitable for 7-16 connectors with a wrench size of 27 or 32 mm | 1.1 or 1.3 inches, and the RCU attachment nut with a wrench size of 41 mm | 1.6 inches. Tighten nuts within a torque range of 25 – 33 Nm depending on connector manufacturers’ specifi cations, respectively the RCU nut with a torque range of 15 – 18 Nm. Kathrein installation set: Type No. 85010077 Set has to be ordered separately! Set consists of three spanners of divers width 27, 32 and 41 mm | 1.1, 1.3 and 1.6 inches 32 | 1.3 41 | 1.6 27 | 1.1 1/2˝ square actuation according to DIN 3120 Form C All dimensions in mm | inches Colour coding: Correlation of each RF input to: – the corresponding adjustment mechanism – the frequency range – the polarization Ventilation hole Spindle with tilting scale 7-16 female (long neck) Adjustment mechanism (protective cap removed) General Instructions for Feederline and RCU Installation for Antennas Please note: In order not to damage the interfaces, please make sure that only the right tools are used. Tighten the feederline connector interfaces solely by using a common torque-wrench with a suitable wrench width. Description of bottom end cap (exemplary picture): Kathrein USA Greenway Plaza II, 2400 Lakeside Blvd., Suite 650, Richardson TX 75082 All specifications are subject to change without notice. The latest specifications are available at www.kathreinusa.com