7580223 TURCK | Alldatasheet

Document overview

  • Manufacturer or author: Provided By alldatasheet.com(free datasheet download site)
  • PDF pages: 4

Technical content

Edition • 2023-07-21T16:33:08+02:00 Frequency Transducer/Pulse Counter 1-channel IM12-FI01-1SF-1R-0/24VDC/CC The frequency transducer IM12- FI01-1SF-1R-0/24VDC/CC transmits frequen- cy signals up to 20,000 Hz galvanically isolat- ed. This device is used for monitoring limit val- ues. The device is suitable for use in Zone 2. The one-channel device is equipped with two inputs for the connection of sensors acc. to EN 60947-5-6 (NAMUR) or potential-free con- tacts. A 3-wire input and a pulse input are also available. A changeover relay is available on the output side. The device is parameterized via rotary cod- ing switches and DIP switches on the side of the device. The relay output is used to monitor whether a limit value exceeds or undershoots a limit value or lies outside a limit value win- dow. Depending on the parameter, the start- up delay (SUD) is activated via input E2 or E3. The devices have a green and a red Power LED (Pwr) for indicating the operating voltage and the parameterization. For each input cir- cuit there is a yellow and a red status LED. An error in the input circuit causes the red LED to flash according to NE44. A yellow LED in- dicates the switch-on delay. A red and a yel- low LED are available to indicate the switch- ing status of the relay. The device can be used in safety circuits up to SIL2 (high and low demand according to IEC 61508) and meets the requirements of NE21. It is equipped with removable spring type ter- minals. The device is equipped with removable spring-type terminals. ■ Input circuits monitored for wire break and short circuit ■ Parameterized via DIP/rotary coding switch ■ Complete galvanic isolation ■ Input reverse-polarity protected ■ Removable spring type terminals ■ Installation in Zone 2 ■ SIL 2

Edition • 2023-07-21T16:33:08+02:00 Type IM12-FI01-1SF-1R-0/24VDC/CC ID 7580223 Nominal voltage 24 VDC Operating voltage 10…30 VDC Power consumption ð 3 W Power dissipation, typical ð 1.7 W Monitoring range/Setting range ð 0.0006…1200000 min NAMUR input NAMUR EN 60947-5-6 No-load voltage 8.2 VDC Short-circuit current 8.2 mA Input resistance 1 kò Cable resistance ð 50 ò Switch-on threshold 1.75 mA Switch-off threshold 1.55 mA Wire breakage threshold ð 0.06 mA Short-circuit threshold ï 6.4 mA 3-wire input No-load voltage 12 VDC 0-signal 0...3VDC 1-signal 5...30 VDC External signal source 0-signal 0…3 VDC 1-signal 5…30 VDC Output circuits Output circuits (digital) 1 x relay (change-over) Output switching voltage relay ð 30 VDC / ð 250 VAC Switching current per output ð 2 A Switching capacity per output ð 500 VA/60 W Switching frequency ð 15 Hz Contact quality AgNi Galvanic isolation Test voltage 2.5 kV RMS E1,E2-E3 375 V peak value acc. to EN 60079-11 E1,E2 supply voltage 375 V peak value acc. to EN 60079-11 Important note For Ex-applications the values specified in the corre- sponding Ex certificates (ATEX, IECEx, UL, etc.) ap- ply. Important note If the device is used in applications to achieve func- tional safety according to IEC 61508, the safety manual must be used. Information in the data sheet are not valid for functional safety. Use in SIL safety circuits SIL 2 acc. to IEC 61508 Displays/Operating elements Operational readiness Green Switching state Yellow Error indication red Dimensions

Edition • 2023-07-21T16:33:08+02:00 Mechanical data Protection class IP20 Flammability class acc. to UL 94 V-0 Ambient temperature -25…+70 °C Storage temperature -40…+80 °C Dimensions 120 x 12.5 x 128 mm Weight 1 g Mounting instructions DIN rail (NS35) Housing material Polycarbonate/ABS Electrical connection Removable spring-type terminals, 2-pin Terminal cross-section 0.2…2.5 mm² (AWG: 24…14) Environmental conditions Operating height Up to 2000 m above sea level Pollution degree II Surge/Overvoltage cate- gory II (EN 61010-1) Standards used Voltage resistance and insulation EN 50178 EN 61010-1 EN 50155 GL VI-7-2 Shock EN 61373 class B EN 50155 GL VI-7-2 EN 60068-2-6 EN 60068-2-27 Temperature EN 60068-2-1 Ad EN 50155 GL VI-7-2 EN 60068-2-2 Bd EN 60068-2-1 Air humidity EN 60068-2-38 EMC EN 50155 GL VI-7-2 NE21 EN 61326-1 EN 61326-3-1 EN 61000-4-2 EN 61000-4-3 EN 61000-4-4 EN 61000-4-5 EN 61000-4-6 EN 61000-4-11 EN 61000-4-29 EN 55011 EN 55016 EN 50121-3-2 EN 61000-6-2

Edition • 2023-07-21T16:33:08+02:00 Accessories Type code Ident-No. Dimension drawing IMX12-SC-2X-4BK 7580940 Screw terminals for IM(X)12 modules; included in delivery: 4 pcs. of 2-pin black terminals IMX12-CC-2X-4BK 7580942 Spring terminals for IM(X)12 modules; included in delivery: 4 pcs. black terminals, 2-pin