74VHC04_04 STMICROELECTRONICS | Alldatasheet

Document overview

  • Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
  • PDF pages: 11

Technical content

I HIGH SPEED: tPD = 3.8ns (TYP.) at VCC = 5V I LOW POWER DISSIPATION: ICC = 2 µA (MAX.) at TA=25°C I HIGH NOISE IMMUNITY: VNIH = VNIL = 28% VCC (MIN.) I POWER DOWN PROTECTION ON INPUTS I SYMMETRICAL OUTPUT IMPEDANCE: OH | = IOL = 8 mA (MIN) I BALANCED PROPAGATION DELAYS: t PLH ≅ tPHL I OPERATING VOLTAGE RANGE: V CC (OPR) = 2V to 5.5V I PIN AND FUNCTION COMPATIBLE WITH

74 SERIES 04

I IMPROVED LATCH-UP IMMUNITY I LOW NOISE: V OLP = 0.8V (MAX.)

DESCRIPTION

The 74VHC04 is an advanced high-speed CMOS HEX INVERTER fabricated with sub-micron silicon gate and double-layer metal wiring C 2MOS technology. The internal circuit is composed of 3 stages including buffer output, which provides high noise immunity and stable output. Power down protection is provided on all inputs and 0 to 7V can be accepted on inputs with no regard to the supply voltage. This device can be used to interface 5V to 3V. All inputs and outputs are equipped with protection circuits against static discharge, giving them 2KV ESD immunity and transient excess voltage. 74VHC04 HEX INVERTER Figure 1: Pin Connection And IEC Logic Symbols Table 1: Order Codes PACKAGE T & R SOP 74VHC04MTR TSSOP 74VHC04TTR TSSOPSOP Rev. 5

Figure 2: Input Equivalent Circuit Table 2: Pin Description Table 3: Truth Table Table 4: Absolute Maximum Ratings Absolute Maximum Ratings are those values beyond which damage to the device may occur. Functional operation under these conditions is not implied Table 5: Recommended Operating Conditions 1) VIN from 30% to 70% of VCC PIN N° SYMBOL NAME AND FUNCTION 1, 3, 5, 9, 11, 13 1A to 6A Data Inputs 2, 4, 6, 8, 10, 12 1Y to 6Y Data Outputs

7 GND Ground (0V)

14 VCC Positive Supply Voltage

Symbol Parameter Value Unit VCC Supply Voltage -0.5 to +7.0 V VI DC Input Voltage -0.5 to +7.0 V VO DC Output Voltage -0.5 to V CC + 0.5 V IIK DC Input Diode Current - 20 mA IOK DC Output Diode Current ± 20 mA IO DC Output Current ± 25 mA ICC or IGND DC V CC or Ground Current ± 75 mA Tstg Storage Temperature -65 to +150 °C TL Lead Temperature (10 sec) 300 °C Symbol Parameter Value Unit VCC Supply Voltage 2 to 5.5 V VI Input Voltage 0 to 5.5 V VO Output Voltage 0 to V CC V Top Operating Temperature -55 to 125 °C dt/dv Input Rise and Fall Time (note 1) (VCC = 3.3 ± 0.3V) (VCC = 5.0 ± 0.5V) 0 to 100 0 to 20 ns/V

Table 6: DC Specifications Table 7: AC Electrical Characteristics (Input tr = tf = 3ns) (*) Voltage range is 3.3V ± 0.3V (**) Voltage range is 5.0V ± 0.5V Symbol Parameter Test Condition Value UnitVCC (V) TA = 25°C -40 to 85°C -55 to 125°C VIH High Level Input Voltage 2.0 1.5 1.5 1.5 V3.0 to 5.5 0.7VCC 0.7VCC 0.7VCC VIL Low Level Input Voltage 2.0 0.5 0.5 0.5 V3.0 to 5.5 0.3VCC 0.3VCC 0.3VCC VOH High Level Output Voltage 2.0 I O =-50 µA 1.9 2.0 1.9 1.9 V 3.0 IO =-4 mA 2.58 2.48 2.4 4.5 IO =-8 mA 3.94 3.8 3.7 VOL Low Level Output Voltage V 3.0 IO =4 mA 0.36 0.44 0.55 4.5 IO =8 mA 0.36 0.44 0.55 II Input Leakage Current 0 to 5.5 VI = 5.5V or GND ± 0.1 ± 1 ± 1 µA ICC Quiescent Supply Current 5.5 VI = VCC or GND 22 0 2 0 µA Symbol Parameter Test Condition Value UnitVCC (V) C L (pF) TA = 25°C -40 to 85°C -55 to 125°C tPLH tPHL Propagation Delay Time

Table 8: Capacitive Characteristics 1) CPD is defined as the value of the IC’s internal equivalent capacitance which is calculated from the operating current consumption without load. (Refer to Test Circuit). Average operating current can be obtained by the following equation. ICC(opr) = CPD x VCC x fIN + ICC /6 (per gate) Table 9: Dynamic Switching Characteristics 1) Worst case package. 2) Max number of outputs defined as (n). Data inputs are driven 0V to 5.0V, (n-1) outputs switching and one output at GND. 3) Max number of data inputs (n) switching. (n-1) switching 0V to 5.0V. Inputs under test switching: 5.0V to threshold (V ILD), 0V to threshold (VIHD), f=1MHz. Figure 3: Test Circuit C L = 15/50pF or equivalent (includes jig and probe capacitance) R T = ZOUT of pulse generator (typically 50Ω ) Symbol Parameter Test Condition Value UnitTA = 25°C -40 to 85°C -55 to 125°C C IN Input Capacitance 41 0 1 0 p F C PD Power Dissipation Capacitance (note 1) 15 pF Symbol Parameter Test Condition Value UnitVCC (V) TA = 25°C -40 to 85°C -55 to 125°C VOLP Dynamic Low Voltage Quiet Output (note 1, 2) 5.0 C L = 50 pF 0.3 0.8 VVOLV -0.8 -0.3 VIHD Dynamic High Voltage Input (note 1, 3) 5.0 3.5 V VILD Dynamic Low Voltage Input (note 1, 3) 5.0 1.5 V

Figure 4: Waveform - Propagation Delays (f=1MHz; 50% duty cycle)

DIM. mm. inch A 1.35 1.75 0.053 0.069 A1 0.1 0.25 0.004 0.010 A2 1.10 1.65 0.043 0.065 B 0.33 0.51 0.013 0.020 C 0.19 0.25 0.007 0.010 D 8.55 8.75 0.337 0.344 E 3.8 4.0 0.150 0.157 e 1.27 0.050 H 5.8 6.2 0.228 0.244 h 0.25 0.50 0.010 0.020 L 0.4 1.27 0.016 0.050 k0 ° 8° 0° 8° ddd 0.100 0.004 SO-14 MECHANICAL DATA 0016019D

DIM. mm. inch A 1.2 0.047 b 0.19 0.30 0.007 0.012 c 0.09 0.20 0.004 0.0089 e 0.65 BSC 0.0256 BSC K0 ˚ 8 ˚0 ˚ 8 ˚ TSSOP14 MECHANICAL DATA c Eb A2A D PIN 1 IDENTIFICATION LKe 0080337D

DIM. mm. inch A 330 12.992 C 12.8 13.2 0.504 0.519 D 20.2 0.795 N 60 2.362 T 22.4 0.882 Ao 6.4 6.6 0.252 0.260 Bo 9 9.2 0.354 0.362 Ko 2.1 2.3 0.082 0.090 Po 3.9 4.1 0.153 0.161 P 7.9 8.1 0.311 0.319 Tape & Reel SO-14 MECHANICAL DATA

DIM. mm. inch A 330 12.992 C 12.8 13.2 0.504 0.519 D 20.2 0.795 N 60 2.362 T 22.4 0.882 Ao 6.7 6.9 0.264 0.272 Bo 5.3 5.5 0.209 0.217 Ko 1.6 1.8 0.063 0.071 Po 3.9 4.1 0.153 0.161 P 7.9 8.1 0.311 0.319 Tape & Reel TSSOP14 MECHANICAL DATA

Table 10: Revision History Date Revision Description of Changes 12-Nov-2004 5 Order Codes Revision - pag. 1.

Information furnished is believed to be accurate and reliable. However, STMicroelectronics assumes no responsibility for the consequences of use of such information nor for any infringement of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of STMicroelectronics. Specifications mentioned in this publication are subject to change without notice. This publication supersedes and replaces all information previously supplied. STMicroelectronics products are not authorized for use as critical components in life support devices or systems without express written approval of STMicroelectronics. The ST logo is a registered trademark of STMicroelectronics All other names are the property of their respective owners © 2004 STMicroelectronics - All Rights Reserved STMicroelectronics group of companies Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan - Malaysia - Malta - Morocco - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America