TC74LCX02F TOSHIBA | Alldatasheet

Document overview

  • Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
  • PDF pages: 8

Technical content

TOSHIBA CMOS DIGITAL INTEGRATED CIRCUIT SILICON MONOLITHIC TC74LCX02F, TC74LCX02FN, TC74LCX02FT LOW VOLTAGE QUAD 2-INPUT NOR GATE WITH 5V TOLERANT INPUTS AND OUTPUTS . . (Note) The JEDEC SOP (FN) is not The TC7ALCXO02 is a high performance CMOS 2-INPUT available in Japan. NOR GATE. Designed for use in 3.3 Volt systems, it Tovacxo2F achieves high speed operation while maintaining the CMOS low power dissipation. The device is designed for low-voltage (3.3V) Vcc applications, but it could be used to interface to 5V supply environment for inputs. All inputs are equipped with protection circuits against static discharge. SOP14-P-300-1.27 TC7ALCXO2FN

FEATURES

@ Low voltage operation : Vcc=2.0~3.6V High speed operation tpd =5.2ns (Max.) NS Zs Act \\ (Vcc =3.0~3.6V) Tela (EGS © Output current © JloHI/lot=24mA (Min.) a (Vcc = 3.0V) SOL14-P-150-1.27 @ Latch-up performance : +500mA TC7ALCXO2FT @ Available in JEDEC SOP, EIAJ SOP and TSSOP @ Power down protection is provided on all inputs and outputs. @ Pin and function compatible with the 74 series ES (74AC/VHC/HC/F/ALS/LS etc.) 02 type. . TSSOP 14-P-0044-0.65 Weight SOP14-P-300-1.27 : 0.18g (Typ.) SOL14-P-150-1.27 : 0.12g (Typ.) TSSOP14-P-0044-0.65 : 0.06g (Typ.) 961001EBA2 malfunction or fail due to their inherent electrical sensitivity and vulnerability to physical stress. It is the responsibility of the buyer, when utilizing TOSHIBA products, to observe standards of safety, and to avoid situations in which a malfunction or failure of a TOSHIBA product could cause loss of human life, bodily injury or damage to property. In developing. your, designs, please ensure that TOSHIBA. products are, used within specified operating ranges as set forth in the most recent products specifications. Also, please keep in mind the precautions and conditions set forth in the TOSHIBA Semiconductor Reliability Handbook 1997-08-05 1/8

PIN ASSIGNMENT IEC LOGIC SYMBOL 1A 2 6 +— 2v 1B 3] 12 4B 8 3A 10

9 B 3Y

28 | 9 38 cup | 8 3A (TOP VIEW) TRUTH TABLE INPUTS OUTPUTS Pat es fy | MAXIMUM _ RATINGS PARAMETER SYMBOL RATING UNIT Power Supply Voltage -0.5~7.0 DC Input Voltage -0.5~7.0 DC Output Voltage v =05~7.0 (Note )] utpu 9 ouT =0.5~Vcc +0.5 (Note 2) Input Diode Current Output Diode Current +50 (Note 3) [ ma | DC Output Current lout Power Dissipation [Pop 80 mw | DC Vec/Ground Current [Tec/Ignp | 100+ ma | (Note 1) VCC=0V (Note 2) High or Low State. IgyT absolute maximum rating must be observed. (Note 3) VouT<GND, Vout>Vcc 9610016802" The information contained herein s presented only as 2 guide for the applications of our products. No responsibility is assumed by, TOSHIBA CORPORATION for any infringements of intellectual property or other rights of the third parties which may result from its use. No license is granted by implication or otherwise under any intellectual property or other rights of TOSHIBA CORPORATION or others. @ The information contained herein is subject to change without notice 1997-08-05 2/8

RECOMMENDED OPERATING CONDITIONS PARAMETER SYMBOL RATING Input Votage a 0~5.5 (Note 5) Output Voltage VouT 0~Vcc (Note 6) Vv Output Current lon/ £24 (Note 7) Utput Curren OH TOL £12 (Note 8) Operating Temperature -40~85 Input Rise And Fall Time 0~10 (Note 9) (Note 4) Data Retention Only (Note 5) VCC=0V (Note 6) High or Low State (Note 7) Vcc =3.0~3.6V (Note 8) Vcc =2.7~3.0V (Note 9) Vin =0.8~2.0V, Vcc =3.0V

ELECTRICAL CHARACTERISTICS

DC characteristics (Ta= -40~85°C) PARAMETER SYMBOL TEST CONDITION MAX. | UNIT Vec (V) inp’ [A tee | Vin | SSSCSCSCSC*di2 38 POT — |, Voltage [U7 Level |_Vu| SSCS =| — OB ovr rn | — | “w* tevel | Von |Vin=Vit llon= ma [27 [22 | — | Output lon==24ma_| 30 | 22 | — | v oltage ioi= 100.8 _[27~36| — | 02 ve tevel | Vor Ivvevin ory, [lL=t2ma [27 [= [03] llov=16ma_[ 30 | — [02] Input Leakage Current | lin _| Vin=0~5.5V 2.7~3.6| — | +50] pA | Power Off Leakage _ Quiescent Supply | Vin=Vcc or GND 2.7~3.6| — | 100] A Current ce Vin/ Vout =3.6~5.5V [2.7~3.6| — [#100] “ Increase In Icc Per Al Vin =Vcc -0.6V 2.7~3. A none pro) — | || 1997-08-05 3/8

AC characteristics (Ta = - 40~85°C) PARAMETER SYMBOL TEST CONDITION Vee (V) jin. | wax. | unre | Propagation Delay teLH ‘i | 27 | — | 60 | - (Fig.1, 2) Time teHL 3.3403] 15 | 5.2 | Output To Output | ost now 27 | — | — | Skew tosHL 3.3403] — | 1.0 | (Note 10) Parameter guaranteed by design. (tosLH =ltpLHm-tpLHnl, tosHL=ltpHLim - tpHinl) DYNAMIC SWITCHING CHARACTERISTICS (Ta = 25°C, Input tp =tf=2.5ns, Cy =50pF, R_ = 5000) PARAMETER SYMBOL TEST CONDITION TYP | UNIT Vec (V) Quiet Output Minimum Dynamic \\Vowvl Vin =3.3V, Vi, ov | 33 | os] v | Vou CAPACITIVE CHARACTERISTICS (Ta = 25°C) PARAMETER SYMBOL TEST CONDITION TYP | UNIT Vec (V) Input Capacitance [33 [7] oF | Output Capacitance CouT | o | 8| pF | Power Dissipation _ (Note 11) Cpp is defined as the value of the internal equivalent capacitance which is calculated from the operating current consumption without load. Average operating current can be obtained by the equation : Icc (opr.) = CPD'Vcc'fin + !cc/4 (Per gate) 1997-08-05 4/8

Fig.1 ourPuT MEASURE "I fF c.=50pe R =5002 AC WAVEFORM Fig.2 tpLH. tpHL te, 2.5ns te, 25ns 30% 2 INPUT 15V t GND Vou 15V oureut Vou tout tpHL 1997-08-05 5/8

SOP14-P-300-1.27 Unit : mm 14 8 HHaAAaaG J | NY all = | wo) oN ao —T- Th Wy SSO HE EE A AE “y 1 7 1.34TYP. 4. AL 5] 10.8MAX 10.3+0.2 N x as “8 OT & $F =| 2 is 70.4] a Sc 0,820.2 Weight : 0.18g (Typ.) 1997-08-05 6/8

S$OL14-P-150-1.27 Unit : mm 14 8 (Note) This package is not available in Japan. HHRREESG =| 4 Rl) & alo oO wo 1 7 0.515TYP 0.42+0.07 7 8.65+0.1 3 x Lpsa § 3 Poi |S 3 Bs] ¢ Pa e Lad ° 3 0.7+0.3 Weight : 0.12g (Typ.) TT 99708-0578

TSSOP 14-P-0044-0.65 Unit : mm 14 8 Coggggea LAA f ofA Toltaig | Hoan ooo | 7 ossTYP 5.00.41 s| % LL ) a 8 rc 0.45~0.75 Weight : 0.06g (Typ.) 1997-08-05 8/8