CY74FCT16373T TI | Alldatasheet

Document overview

  • Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
  • PDF pages: 7

Technical content

Features

  • FCT-E speed at 3.4 ns
  • Power-off disable outputs permits live insertion
  • Edge-rate control circuitry for significantly improved noise characteristics
  • Typical output skew < 250 ps
  • ESD > 2000V
  • TSSOP (19.6-mil pitch) and SSOP (25-mil pitch) packages
  • Industrial temperature range of-40˚C to +85˚C CC = 5V– 10% CY74FCT16373T Features:
  • 64 mA sink current, 32 mA source current
  • Typical VOLP (ground bounce) <1.0V at VCC = 5V, TA = 25˚C CY74FCT162373T Features:
  • Balanced 24 mA output drivers
  • Reduced system switching noise
  • Typical V OLP (ground bounce) <0.6V at VCC = 5V, TA = 25˚C Functional Description CY74FCT16373T and CY74FCT162373T are 16-bit D-type latches designed for use in bus applications requiring high speed and low power. These devices can be used as two independent 8-bit latches or as a single 16-bit latch by connecting the Output Enable ( OE) and Latch (LE) inputs. Flow-through pinout and small shrink packaging aid in simplifying board layout. The output buffers are designed with power-off disable feature that allows live insertion of boards. The CY74FCT16373T is ideally suited for driving high-capacitance loads and low-impedance backplanes. The CY74FCT162373T has 24-mA balanced output drivers with current limiting resistors in the outputs. This reduces the need for external terminating resistors and provides for minimal undershoot and reduced ground bounce. The CY74FCT162373T is ideal for driving transmission lines. Logic Block Diagrams Pin Configuration D C 1OE FCT162373-1 1LE 1D 1 1O 1 TO 7 OTHER CHANNELS D C 2OE FCT162373-2 2LE 2D 1 2O 1 GND 1OE SSOP/TSSOP Top View 1O 1 1O 2 1O 3 1O 4 1D 1 1D 2 1D 3 1D 4 1LE GND GND VCC 1O 7 1O 8 1O 5 1O 6 1D 5 1D 6 1D 7 1D 8 VCC GND GND 2O 3 2O 4 2O 1 2O 2 2D 1 2D 2 2D 3 2D 4 GND GND VCC 2O 7 2O 8 2O 5 2O 6 2D 5 2D 6 2D 7 2D 8 VCC GND 2OE 2LE FCT162373-3 TO 7 OTHERCHANNELS

Maximum Ratings [2, 3] (Above which the useful life may be impaired. For user guidelines, not tested.) Ambient Temperature with DC Output Current (per MIL-STD-883, Method 3015) Pin Description Name Description D Data Inputs LE Latch Enable Inputs (Active HIGH) OE Output Enable Inputs (Active LOW) O Three-State Outputs Function Table[1] Inputs Outputs D LE OE O H H L H L H L L X L L Q 0 X X H Z Operating Range Range Ambient Temperature VCC Industrial -40°C to +85°C 5V – 10% Electrical CharacteristicsOver the Operating Range Parameter Description Test Conditions Min. Typ.[4] Max. Unit VIH Input HIGH Voltage 2.0 V VIL Input LOW Voltage 0.8 V VH Input Hysteresis[5] 100 mV VIK Input Clamp Diode Voltage VCC =Min., IIN=-18 mA -0.7 -1.2 V IIH Input HIGH Current VCC =Max., VI=V CC –1 mA IIL Input LOW Current VCC =Max., VI=GND –1 mA IOZH High Impedance Output Current (Three-State Output pins) VCC =Max., VOUT =2.7V –1 mA IOZL High Impedance Output Current (Three-State Output pins) VCC =Max., VOUT =0.5V –1 mA IOS Short Circuit Current[6] VCC =Max., VOUT =GND -80 -140 -200 mA IO Output Drive Current[6] VCC =Max., VOUT =2.5V -50 -180 mA IOFF Power-Off Disable VCC =0V, VOUT £4.5V[7] –1 mA Output Drive Characteristics for CY74FCT16373T Parameter Description Test Conditions Min. Typ.[4] Max. Unit VOH Output HIGH Voltage VCC =Min., IOH =-3 mA 2.5 3.5 V VCC =Min., IOH =-15 mA 2.4 3.5 V VCC =Min., IOH =-32 mA 2.0 3.0 V VOL Output LOW Voltage VCC =Min., IOL =64 mA 0.2 0.55 V Notes: 2. Operation beyond the limits set forth may impair the useful life of the device. Unless otherwise noted, these limits are over the operating free-airtemperature range. 3. Unused inputs must always be connected to an appropriate logic voltage level, preferably either VCC or ground. 4. Typical values are at VCC =5.0V, TA= +25˚C ambient. 5. This parameter is specified but not tested. 6. Not more than one output should be shorted at a time. Duration of short should not exceed one second. The use of high-speed test apparatus and/or sample and hold techniques are preferable in order to minimize internal chip heating and more accurately reflect operational values. Otherwise prolonged shorting of a high output may raise the chip temperature well above normal and thereby cause invalid readings in other parametric tests. In any sequence of parameter tests, I OS tests should be performed last. 7. Tested at +25˚C.

Output Drive Characteristics for CY74FCT162373T Parameter Description Test Conditions Min. Typ.[4] Max. Unit IODL Output LOW Current[6] VCC =5V, VIN=V IH or VIL, VOUT =1.5V 60 115 150 mA IODH Output HIGH Current[6] VCC =5V, VIN=V IH or VIL, VOUT =1.5V -60 -115 -150 mA VOH Output HIGH Voltage VCC =Min., IOH =-24 mA 2.4 3.3 V VOL Output LOW Voltage VCC =Min., IOL =24 mA 0.3 0.55 V Capacitance[5](TA = +25˚C, f = 1.0 MHz) Parameter Description Test Conditions Typ.[4] Max. Unit C IN Input Capacitance VIN = 0V 4.5 6.0 pF C OUT Output Capacitance VOUT = 0V 5.5 8.0 pF Power Supply Characteristics Parameter Description Test Conditions Typ.[4] Max. Unit ICC Quiescent Power Supply CurrentVCC =Max. VIN£0.2V, VIN‡VCC -0.2V 5 500 mA DICC Quiescent Power Supply Current (TTL inputs HIGH) VCC =Max. VIN=3.4V[8] 0.5 1.5 mA ICCD Dynamic Power Supply Current [9] VCC =Max., One Input Toggling, 50% Duty Cycle, Outputs Open, OE=GND VIN=V CC or VIN=GND 60 100 mA/MHz IC Total Power Supply Current[10] VCC =Max., f1=10 MHz, 50% Duty Cycle, Outputs Open, One Bit Toggling, OE=GND, LE=V CC VIN=V CC or VIN=GND 0.6 1.5 mA VIN=3.4V or VIN=GND 0.9 2.3 mA VCC =Max., f1=2.5 MHz, 50% Duty Cycle, Outputs Open, Sixteen Bits Toggling, OE=GND, LE=V CC VIN=V CC or VIN=GND 2.4 4.5[11] mA VIN=3.4V or VIN=GND 6.4 16.5[11] mA Notes: 8. Per TTL driven input (VIN=3.4V); all other inputs at VCC or GND. 9. This parameter is not directly testable, but is derived for use in Total Power Supply calculations. 10. IC =I QUIESCENT + IINPUTS + IDYNAMIC IC =I CC +DICC D H N T+ICCD (f0/2 + f1N 1) ICC = Quiescent Current with CMOS input levels DICC = Power Supply Current for a TTL HIGH input(VIN=3.4V) D H = Duty Cycle for TTL inputs HIGH N T = Number of TTL inputs at DH ICCD = Dynamic Current caused by an input transition pair (HLH or LHL) f0 = Clock frequency for registered devices, otherwise zero f1 = Input signal frequency N 1 = Number of inputs changing at f1 All currents are in milliamps and all frequencies are in megahertz. 11. Values for these conditions are examples of the ICC formula. These limits are specified but not tested.

Switching CharacteristicsOver the Operating Range[12] CY74FCT16373AT CY74FCT162373AT Parameter Description Min. Max. Unit Fig. No.[13] tPLH tPHL Propagation Delay D to O 1.5 5.2 ns 1, 3 tPLH tPHL Propagation Delay LE to O 2.0 6.7 ns 1, 5 tPZH tPZL Output Enable Time 1.5 6.1 ns 1, 7, 8 tPHZ tPLZ Output Disable Time 1.5 5.5 ns 1, 7, 8 tSU Set-Up Time HIGH or LOW, D to LE 2.0 ns 9 tH Hold Time HIGH or LOW, D to LE 1.5 ns 9 tW LE Pulse Width HIGH 3.3 ns 5 tSK(O) Output Skew[14] 0.5 ns — CY74FCT16373CT CY74FCT162373CT CY74FCT16373ET CY74FCT162373ET tPLH tPHL Propagation Delay D to O 1.5 4.2 1.5 3.4 ns 1, 3 tPLH tPHL Propagation Delay LE to O 2.0 5.5 2.0 3.7 ns 1, 5 tPZH tPZL Output Enable Time 1.5 5.5 1.5 4.4 ns 1, 7, 8 tPHZ tPLZ Output Disable Time 1.5 5.0 1.5 3.6 ns 1, 7, 8 tSU Set-Up Time HIGH or LOW, D to LE 2.0 1.0 ns 9 tH Hold Time HIGH or LOW, D to LE 1.5 1.0 ns 9 tW LE Pulse Width HIGH 3.3 3.0 ns 5 tSK(O) Output Skew[14] 0.5 0.5 ns — Notes: 12. Minimum limits are specified but not tested on Propagation Delays. 13. See “Parameter Measurement Information” in the General Information section. 14. Skew between any two outputs of the same package switching in the same direction. This parameter is ensured by design.

(ns) Ordering Code Package Name Package Type Operating Range

3.4 CY74FCT16373ETPACT Z48 48-Lead (240-Mil) TSSOP Industrial

CY74FCT16373ETPVC/PVCT O48 48-Lead (300-Mil) SSOP

4.2 CY74FCT16373CTPACT Z48 48-Lead (240-Mil) TSSOP Industrial

CY74FCT16373CTPVC/PVCT O48 48-Lead (300-Mil) SSOP

5.2 CY74FCT16373ATPACT Z48 48-Lead (240-Mil) TSSOP Industrial

CY74FCT16373ATPVC/PVCT O48 48-Lead (300-Mil) SSOP Speed (ns) Ordering Code Package Name Package Type Operating Range 3.4 74FCT162373ETPACT Z48 48-Lead (240-Mil) TSSOP Industrial CY74FCT162373ETPVC O48 48-Lead (300-Mil) SSOP 74FCT162373ETPVCT O48 48-Lead (300-Mil) SSOP 4.2 74FCT162373CTPACT Z48 48-Lead (240-Mil) TSSOP Industrial CY74FCT162373CTPVC O48 48-Lead (300-Mil) SSOP 74FCT162373CTPVCT O48 48-Lead (300-Mil) SSOP 5.2 74FCT162373ATPACT Z48 48-Lead (240-Mil) TSSOP Industrial CY74FCT162373ATPVC O48 48-Lead (300-Mil) SSOP 74FCT162373ATPVCT O48 48-Lead (300-Mil) SSOP

48-Lead Shrunk Small Outline PackageO48 48-Lead Thin Shrunk Small Outline PackageZ48

Texas Instruments and its subsidiaries (TI) reserve the right to make changes to their products or to discontinue any product or service without notice, and advise customers to obtain the latest version of relevant information to verify, before placing orders, that information being relied on is current and complete. All products are sold subject to the terms and conditions of sale supplied at the time of order acknowledgement, including those pertaining to warranty, patent infringement, and limitation of liability. TI warrants performance of its semiconductor products to the specifications applicable at the time of sale in accordance with TI’s standard warranty. Testing and other quality control techniques are utilized to the extent TI deems necessary to support this warranty. Specific testing of all parameters of each device is not necessarily performed, except those mandated by government requirements. CERTAIN APPLICATIONS USING SEMICONDUCTOR PRODUCTS MAY INVOLVE POTENTIAL RISKS OF DEATH, PERSONAL INJURY, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE (“CRITICAL APPLICATIONS”). TI SEMICONDUCTOR PRODUCTS ARE NOT DESIGNED, AUTHORIZED, OR WARRANTED TO BE SUITABLE FOR USE IN LIFE-SUPPORT DEVICES OR SYSTEMS OR OTHER CRITICAL APPLICATIONS. INCLUSION OF TI PRODUCTS IN SUCH APPLICATIONS IS UNDERSTOOD TO BE FULLY AT THE CUSTOMER’S RISK. In order to minimize risks associated with the customer’s applications, adequate design and operating safeguards must be provided by the customer to minimize inherent or procedural hazards. TI assumes no liability for applications assistance or customer product design. TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other intellectual property right of TI covering or relating to any combination, machine, or process in which such semiconductor products or services might be or are used. TI’s publication of information regarding any third party’s products or services does not constitute TI’s approval, warranty or endorsement thereof. Copyright  2000, Texas Instruments Incorporated