74F832 PHILIPS | Alldatasheet

Document overview

  • Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
  • PDF pages: 8

Technical content

/C0109 /C0110 /C0114 74F832, 74F1832 Hex 2-input OR drivers Product specification IC15 Data Handbook

1991 Jan 02

Philips Semiconductors Product specification 74F832/74F1832Hex 2-input OR drivers 2January 2, 1991 853-1529 01348

FEATURES

  • High capacitive drive capability
  • Choice of configuration Corner VCC and GND – 74F832 Center VCC and GND – 74F1832
  • Typical propagation delay of 3.5ns
  • Superior ground noise characteristics (implemented using output edge rate control)
  • Increased source and sink current (64mA) TYPE TYPICAL PROP- AGATION DELAY TYPICAL SUPPLY CURRENT ( TOTAL) 74F832 3.5ns 26mA 74F1832 3.5ns 26mA

ORDERING INFORMATION

DESCRIPTION COMMERCIAL RANGE VCC = 5V ±10%, Tamb = 0°C to +70°C PKG DWG # 20–pin plastic Dual In-line Package N74F832N, N74F1832N SOT146-1 20–pin plastic Small Outline Large N74F832D, N74F1832D SOT163-1 INPUT AND OUTPUT LOADING AND FAN OUT TABLE PINS DESCRIPTION 74F (U.L.) HIGH/LOW LOAD VALUE HIGH/LOW Dna – Dnb Data inputs 1.0/0.033 20µA/20µA Q0 – Q5 Data outputs 3200/106.7 64mA/64mA NOTE: One (1.0) FAST unit load is defined as: 20µA in the high state and 0.6mA in the low state. PIN CONFIGURATION 10 11

20 VCC

VCC = Pin 20 GND = Pin 10 D0a D0bD1a D2a D2b D3aD3bD1b Q0 Q1 Q2 Q3 36 9 1 1 1 245 78 1 2 1 3 Q4 Q5 14 17 D4aD4bD5a D5b 15 16 18 19 74F832 SF00512 IEC/IEEE SYMBOL 74F832 SF00513

Philips Semiconductors Product specification 74F832/74F1832Hex 2-input OR drivers January 2, 1991 3 PIN CONFIGURATION 10 11

20 D4a

V CC D0a D0b D1a D1b 74F1832 SF00514 LOGIC SYMBOL VCC = Pin 5 GND = Pin 15 D0a D0bD1a D2a D2b D3a D3bD1b Q0 Q1 Q2 Q3 81 11 4 1 6 67 9 1 0 1 2 1 3 1 7 1 8 Q4 Q5 19 2 D4a D4bD5a D5b 20 1 3 4 74F1832 SF00515 IEC/IEEE SYMBOL 74F1832 SF00516 LOGIC DIAGRAM D0a D0b D1a D1b D2a D2b D3a D3b VCC = Pin 20 GND = Pin 10 D4a D4b D5a D5b QO D0a D0b D1a D1b D2a D2b D3a D3b D4a D4b D5a D5b QO VCC = Pin 5 GND = Pin 15 74F832 74F1832 SF00517 FUNCTION TABLE INPUTS OUTPUT Dna Dnb Qn H X H X H H L L L NOTES: H = High voltage level L = Low voltage level X = Don’t care

Philips Semiconductors Product specification 74F832/74F1832Hex 2-input OR drivers January 2, 1991 4 ABSOLUTE MAXIMUM RATINGS (Operation beyond the limit set forth in this table may impair the useful life of the device. Unless otherwise noted these limits are over the operating free air temperature range.) SYMBOL PARAMETER RATING UNIT VCC Supply voltage –0.5 to +7.0 V VIN Input voltage –0.5 to +7.0 V IIN Input current –30 to +5 mA VOUT Voltage applied to output in high output state –0.5 to VCC V IOUT Current applied to output in low output state 96 mA Tamb Operating free air temperature range 0 to +70 °C Tstg Storage temperature range –65 to +150 °C RECOMMENDED OPERATING CONDITIONS SYMBOL PARAMETER LIMITS TA = –40 to +85°CUNIT MIN NOM MAX VCC Supply voltage 4.5 5.0 5.5 V VIH High–level input voltage 2.0 V VIL Low–level input voltage 0.8 V IIk Input clamp current –18 mA IOH High–level output current –64 mA IOL Low–level output current 64 mA Tamb Operating free air temperature range 0 +70 °C DC ELECTRICAL CHARACTERISTICS (Over recommended operating free-air temperature range unless otherwise noted.) SYMBOL PARAMETER TEST CONDITIONS 1 LIMITS UNIT MIN TYP 2 MAX VOH High-level output voltage VCC = MIN, VIL = MAX ±10%V CC 2.0 V VIH = MIN, IOH = MAX ±5%V CC 2.0 V VOL Low-level output voltage VCC = MIN, VIL = MAX ±10%V CC 0.38 0.55 V VIH = MIN, IOl = MAX ±5%V CC 0.38 0.55 V VIK Input clamp voltage VCC = MIN, II = IIK -0.73 -1.2 V II Input current at maximum input voltageVCC = MAX, VI = 7.0V 100 µA IIH High–level input current VCC = MAX, VI = 2.7V 20 µA IIL Low–level input current VCC = MAX, VI = 0.5V -20 µA IO Output current3 VCC = MAX -60 -180 mA ICC Supply current (total) ICCH VCC = MAX VIN = GND 21 30 mA ICCL VIN = 4.5V 31 44 mA NOTES: 1. For conditions shown as MIN or MAX, use the appropriate value specified under recommended operating conditions for the applicable type. 2. All typical values are at VCC = 5V, Tamb = 25°C. 3. The output conditions have been chosen to produce a current that closely approximates one half of the true short–circuit output current, IOS .

Philips Semiconductors Product specification 74F832/74F1832Hex 2-input OR drivers January 2, 1991 5 AC ELECTRICAL CHARACTERISTICS LIMITS Tamb = +25°C Tamb = 0°C to +70°C SYMBOL PARAMETER TEST VCC = +5.0V VCC = +5.0V ± 10% UNIT CONDITION C L = 50pF, R L = 500Ω C L = 50pF, R L = 500Ω MIN TYP MAX MIN MAX tPLH tPHL Propagation delay Dna, Dnb to Qn Waveform 1 2.0 2.0 4.0 3.5 6.0 6.0 2.0 1.5 6.5 6.5 ns tsk(o) Output skew1, 2 Waveform 2 2.0 2.5 ns NOTES: 1. | tPN actual – tPM actual | for any output compared to any other output where N and M are either LH or HL. 2. Skew times are valid only under same test conditions (temperature, VCC , loading, etc.,). AC WAVEFORMS VMVM VMVM Qn Dna, Dnb tPLH tPHL SF00054 Waveform 1. Propagation delay for inverting output VM VM Qn tsk(0) Qn SF00481 Waveform 2. Output skew NOTE: For all waveforms, VM = 1.5V. TEST CIRCUIT AND WAVEFORMS tw 90% VM 10% 90% VM 10% 90% VM 10% 90% VM 10% NEGATIVE PULSE POSITIVE PULSE tw AMP (V) tTHL (tf ) INPUT PULSE REQUIREMENTS rep. rate tw tTLH tTHL 1MHz 500ns 2.5ns 2.5ns Input Pulse Definition VCC family 74F D.U.T.PULSE GENERATOR R LC LR T VIN VOUT Test Circuit for Totem-Pole Outputs DEFINITIONS: R L = Load resistor; see AC ELECTRICAL CHARACTERISTICS for value. C L = Load capacitance includes jig and probe capacitance; see AC ELECTRICAL CHARACTERISTICS for value. R T = Termination resistance should be equal to ZOUT of pulse generators. tTHL (tf ) tTLH (tr ) tTLH (tr ) AMP (V) amplitude 3.0V 1.5V VM SF00006

Philips Semiconductors Product specification 74F832, 74F1832Hex 2-input OR drivers

1991 Jan 02 6

DIP20: plastic dual in-line package; 20 leads (300 mil) SOT146-1

Philips Semiconductors Product specification 74F832, 74F1832Hex 2-input OR drivers

1991 Jan 02 7

SO20: plastic small outline package; 20 leads; body width 7.5 mm SOT163-1

Philips Semiconductors Product specification 74F832, 74F1832Hex 2-input OR drivers yyyy mmm dd 8 Definitions Short-form specification — The data in a short-form specification is extracted from a full data sheet with the same type number and title. For detailed information see the relevant data sheet or data handbook. Limiting values definition — Limiting values given are in accordance with the Absolute Maximum Rating System (IEC 134). Stress above one or more of the limiting values may cause permanent damage to the device. These are stress ratings only and operation of the device at these or at any other conditions above those given in the Characteristics sections of the specification is not implied. Exposure to limiting values for extended periods may affect device reliability. Application information — Applications that are described herein for any of these products are for illustrative purposes only. Philips Semiconductors make no representation or warranty that such applications will be suitable for the specified use without further testing or modification. Disclaimers Life support — These products are not designed for use in life support appliances, devices or systems where malfunction of these products can reasonably be expected to result in personal injury. Philips Semiconductors customers using or selling these products for use in such applications do so at their own risk and agree to fully indemnify Philips Semiconductors for any damages resulting from such application. Right to make changes — Philips Semiconductors reserves the right to make changes, without notice, in the products, including circuits, standard cells, and/or software, described or contained herein in order to improve design and/or performance. Philips Semiconductors assumes no responsibility or liability for the use of any of these products, conveys no license or title under any patent, copyright, or mask work right to these products, and makes no representations or warranties that these products are free from patent, copyright, or mask work right infringement, unless otherwise specified. Philips Semiconductors

811 East Arques Avenue

P.O. Box 3409 Sunnyvale, California 94088–3409 Telephone 800-234-7381  Copyright Philips Electronics North America Corporation 1998 All rights reserved. Printed in U.S.A. print code Date of release: 10-98 Document order number: 9397-750-05187 /C0109 /C0110 /C0114 Data sheet status Objective specification Preliminary specification Product specification Product status Development Qualification Production Definition [1] This data sheet contains the design target or goal specifications for product development. Specification may change in any manner without notice. This data sheet contains preliminary data, and supplementary data will be published at a later date. Philips Semiconductors reserves the right to make chages at any time without notice in order to improve design and supply the best possible product. This data sheet contains final specifications. Philips Semiconductors reserves the right to make changes at any time without notice in order to improve design and supply the best possible product. Data sheet status [1] Please consult the most recently issued datasheet before initiating or completing a design.