74F379A PHILIPS | Alldatasheet
Document overview
- Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
- PDF pages: 10
Technical content
/C0109 /C0110 /C0114 74F379A Quad register Product specification IC15 Data Handbook
1996 Mar 12
Philips Semiconductors Product specification 74F379AQuad register
21996 Mar 12 853-0027 16555
FEATURES
- Edge–triggered D–type inputs
- Buffered positive edge–triggered clock
- Buffered common enable input
- True and complementary outputs
- Offers light loading PNP inputs (IIL = –20µA)
DESCRIPTION
The 74F379A is a 4–bit register with buffered common enable (E). This device is similar to the 74F175A but features the common enable rather than common master reset. TYPE TYPICAL fmax TYPICAL SUPPLY CURRENT (TOTAL) 74F379A 200MHz 29mA
ORDERING INFORMATION
DESCRIPTION COMMERCIAL RANGE VCC = 5V ±10%, Tamb = 0°C to +70°C PKG, DWG. # 16–pin plastic DIP N74F379AN SOT38–4 16–pin plastic SO N74F379AD SOT109–1 INPUT AND OUTPUT LOADING AND FAN OUT TABLE TYPE PINS DESCRIPTION 74F (U.L.) HIGH/ LOW LOAD VALUE HIGH/LOW D0 – D3 Data inputs 1.0/0.033 20µA/20µA 74F379A CP Clock pulse input (active rising edge) 1.0/0.033 20µA/20µA E Enable input (active low) 1.0/0.033 20µA/20µA Q0 – Q3 True outputs 50/33 1.0mA/20mA Q 0 – Q3 Complementary outputs 50/33 15mA/20mA Note to input and output loading and fan out table 1. One (1.0) FAST unit load is defined as: 20µA in the high state and 0.6mA in the low state. PIN CONFIGURATION 107 SF00354 E Q 0 Q 1 GND VCC Q 3 Q 2 CP LOGIC SYMBOL VCC = Pin 16 GND = Pin 8 SF00355 4 5 12 13 D0 D1 D2 D3 CP E Q0 Q0 Q1 Q1 Q2 Q2 Q3 Q3 3 2 6 7 11 10 14 15
Philips Semiconductors Product specification 74F379AQuad register
1996 Mar 12 3
H ↑ X NC NC L ↑ h H L L ↑ l L H Notes to function table H = High–voltage level h = High state must be present one setup time before the low–to–high clock transition L = Low–voltage level l = Low state must be present one setup time before the low–to–high clock transition NC= No change X = Don’t care ↑ = Low–to–high clock transition LOGIC DIAGRAM DQ E Q 0Q 0 CP E VCC = Pin 16 GND = Pin 8 CP DQ E CP DQ E CP DQ E CP Q 32 67 Q 1Q 1 11 10 Q 2Q 2 14 15 Q 3Q 3 SF00357
Philips Semiconductors Product specification 74F379AQuad register
1996 Mar 12 4
(Operation beyond the limit set forth in this table may impair the useful life of the device. Unless otherwise noted these limits are over the operating free air temperature range.) SYMBOL PARAMETER RATING UNIT VCC Supply voltage –0.5 to +7.0 V VIN Input voltage –0.5 to +7.0 V IIN Input current –30 to +5 mA VOUT Voltage applied to output in high output state –0.5 to VCC V IOUT Current applied to output in low output state 40 mA Tamb Operating free air temperature range 0 to +70 °C Tstg Storage temperature range –65 to +150 °C RECOMMENDED OPERATING CONDITIONS SYMBOL PARAMETER LIMITS UNIT MIN NOM MAX VCC Supply voltage 4.5 5.0 5.5 V VIH High–level input voltage 2.0 V VIL Low–level input voltage 0.8 V IIk Input clamp current –18 mA IOH High–level output current –1 mA IOL Low–level output current 20 mA Tamb Operating free air temperature range 0 +70 °C DC ELECTRICAL CHARACTERISTICS (Over recommended operating free-air temperature range unless otherwise noted.) SYMBOL PARAMETER TEST LIMITS UNIT CONDITIONS 1 MIN TYP 2 MAX VOH High-level output voltage VCC = MIN, VIL = MAX, ±10%V CC 2.5 V VIH = MIN, IOH = MAX ±5%V CC 2.7 3.4 V VOL Low-level output voltage VCC = MIN, VIL = MAX, ±10%V CC 0.35 0.50 V VIH = MIN, IOL = MAX ±5%V CC 0.35 0.50 V VIK Input clamp voltage VCC = MIN, II = IIK –0.73 -1.2 V II Input current at maximum input voltage VCC = 0.0V, VI = 7.0V 100 µA IIH High–level input current VCC = MAX, VI = 2.7V 20 µA IIL Low–level input current –20 µA IOS Short–circuit output current3 VCC = MAX -60 -150 mA ICC Supply current (total) 29 42 mA Notes to DC electrical characteristics 1. For conditions shown as MIN or MAX, use the appropriate value specified under recommended operating conditions for the applicable type. 2. All typical values are at VCC = 5V, Tamb = 25°C. 3. Not more than one output should be shorted at a time. For testing IOS , the use of high-speed test apparatus and/or sample-and-hold techniques are preferable in order to minimize internal heating and more accurately reflect operational values. Otherwise, prolonged shorting of a high output may raise the chip temperature well above normal and thereby cause invalid readings in other parameter tests. In any sequence of parameter tests, IOS tests should be performed last.
Philips Semiconductors Product specification 74F379AQuad register
1996 Mar 12 5
AC ELECTRICAL CHARACTERISTICS LIMITS Tamb = +25°C Tamb = 0°C to +70°C SYMBOL PARAMETER TEST VCC = +5.0V VCC = +5.0V ± 10% UNIT CONDITION C L = 50pF, RL = 500Ω C L = 50pF, RL = 500Ω MIN TYP MAX MIN MAX fmax Maximum clock frequency Waveform 1 175 200 155 MHz tPLH tPHL Propagation delay CP to Qn or Qn Waveform 1 2.0 4.0 3.5 5.5 6.5 8.0 2.0 3.5 7.0 8.5 ns AC SETUP REQUIREMENTS LIMITS Tamb = +25°C Tamb = 0°C to +70°C SYMBOL PARAMETER TEST VCC = +5.0V VCC = +5.0V ± 10% UNIT CONDITION C L = 50pF, RL = 500Ω C L= 50pF, RL = 500Ω MIN TYP MAX MIN MAX tsu (H) tsu (L) Setup time, high or low level Dn to CP Waveform 2 3.0 3.0 3.5 3.5 ns th (H) th (L) Hold time, high or low level Dn to CP Waveform 2 0 ns tsu (H) tsu (L) Setup time, high or low level E to CP Waveform 2 4.0 3.5 4.5 4.0 ns th (H) th (L) Hold time, high or low level E to CP Waveform 2 0 ns tw (H) tw (L) CP Pulse width, high or low Waveform 1 3.5 4.5 3.5 4.5 ns AC WAVEFORMS CP VM VMVM tw (H) 1/fmax VMVM tPLHtw (L)tPHL Qn, Qn SF00358 Waveform 1. Propagation delay for clock input to output, clock pulse widths, and maximum clock frequency VM VM VM VM VM VM tsu(L) t h(L)tsu(H) t h(H) En, Dn CP SF00296 Waveform 2. Data and enable setup time and hold times Notes to AC waveforms 1. For all waveforms, VM = 1.5V. 2. The shaded areas indicate when the input is permitted to change for predictable output performance.
Philips Semiconductors Product specification 74F379AQuad register
1996 Mar 12 6
tw 90% VM 10% 90% VM 10% 90% VM 10% 90% VM 10% NEGATIVE PULSE POSITIVE PULSE tw AMP (V) tTHL (tf ) INPUT PULSE REQUIREMENTS rep. rate tw tTLH tTHL 1MHz 500ns 2.5ns 2.5ns Input Pulse Definition VCC family 74F D.U.T.PULSE GENERATOR R LC LR T VIN VOUT Test Circuit for Totem-Pole Outputs DEFINITIONS: R L = Load resistor; see AC ELECTRICAL CHARACTERISTICS for value. C L = Load capacitance includes jig and probe capacitance; see AC ELECTRICAL CHARACTERISTICS for value. R T = Termination resistance should be equal to ZOUT of pulse generators. tTHL (tf ) tTLH (tr ) tTLH (tr ) AMP (V) amplitude 3.0V 1.5V VM SF00006
Philips Semiconductors Product specification 74F379AQuad register
1996 Mar 12 7
DIP16: plastic dual in-line package; 16 leads (300 mil) SOT38-4
Philips Semiconductors Product specification 74F379AQuad register
1996 Mar 12 8
SO16: plastic small outline package; 16 leads; body width 3.9 mm SOT109-1
Philips Semiconductors Product specification 74F379AQuad register
1996 Mar 12 9
Philips Semiconductors Product specification 74F379AQuad register yyyy mmm dd 10 Definitions Short-form specification — The data in a short-form specification is extracted from a full data sheet with the same type number and title. For detailed information see the relevant data sheet or data handbook. Limiting values definition — Limiting values given are in accordance with the Absolute Maximum Rating System (IEC 134). Stress above one or more of the limiting values may cause permanent damage to the device. These are stress ratings only and operation of the device at these or at any other conditions above those given in the Characteristics sections of the specification is not implied. Exposure to limiting values for extended periods may affect device reliability. Application information — Applications that are described herein for any of these products are for illustrative purposes only. Philips Semiconductors make no representation or warranty that such applications will be suitable for the specified use without further testing or modification. Disclaimers Life support — These products are not designed for use in life support appliances, devices or systems where malfunction of these products can reasonably be expected to result in personal injury. Philips Semiconductors customers using or selling these products for use in such applications do so at their own risk and agree to fully indemnify Philips Semiconductors for any damages resulting from such application. Right to make changes — Philips Semiconductors reserves the right to make changes, without notice, in the products, including circuits, standard cells, and/or software, described or contained herein in order to improve design and/or performance. Philips Semiconductors assumes no responsibility or liability for the use of any of these products, conveys no license or title under any patent, copyright, or mask work right to these products, and makes no representations or warranties that these products are free from patent, copyright, or mask work right infringement, unless otherwise specified. Philips Semiconductors
811 East Arques Avenue
P.O. Box 3409 Sunnyvale, California 94088–3409 Telephone 800-234-7381 Copyright Philips Electronics North America Corporation 1998 All rights reserved. Printed in U.S.A. print code Date of release: 10-98 Document order number: 9397-750-05123 /C0109 /C0110 /C0114 Data sheet status Objective specification Preliminary specification Product specification Product status Development Qualification Production Definition [1] This data sheet contains the design target or goal specifications for product development. Specification may change in any manner without notice. This data sheet contains preliminary data, and supplementary data will be published at a later date. Philips Semiconductors reserves the right to make chages at any time without notice in order to improve design and supply the best possible product. This data sheet contains final specifications. Philips Semiconductors reserves the right to make changes at any time without notice in order to improve design and supply the best possible product. Data sheet status [1] Please consult the most recently issued datasheet before initiating or completing a design.