74F153 PHILIPS | Alldatasheet
Document overview
- Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
- PDF pages: 8
Technical content
/C0109 /C0110 /C0114 74F153 Dual 4-line to 1-line multiplexer Product specification 1996 Jan 05 INTEGRATED CIRCUITS IC15 Data Handbook
Philips Semiconductors Product specification 74F153Dual 4-line to 1-line multiplexer
21996 Jan 05 853–0100 16187
FEATURES
- Non-inverting outputs
- Separate enable for each section
- Common select inputs
- See 74F253 for 3-State version
DESCRIPTION
The 74F153 is a dual 4-input multiplexer that can select 2 bits of data from up to four sources selected by common Select inputs (S0, S1). The two 4-input multiplexer circuits have individual active-Low Enables (Ea, Eb) which can be used to strobe the outputs independently. Outputs (Ya, Yb) are forced Low when the corresponding Enables (E a, Eb) are High. The 74F153 is the logic implementation of a 2-pole, 4-position switch where the switch is determined by the logic levels supplied to the common select inputs. TYPE TYPICAL PROPAGATION DELAY TYPICAL SUPPLY CURRENT (TOTAL) 74F153 7.0ns 12mA PIN CONFIGURATION 107 Ya VCC I2b I1b I0b I3b Eb Ea I0a I3a I2a I1a 98GND Yb SF00146
ORDERING INFORMATION
VCC = 5V ±10%, Tamb = 0°C to +70°C PKG. DWG. # 16-pin plastic DIP N74F153N SOT38-4 16-pin plastic SO N74F153D SOT109-1 INPUT AND OUTPUT LOADING AND FAN-OUT TABLE PINS DESCRIPTION 74F (U.L.) HIGH/LOW LOAD VALUE HIGH/LOW I0a – I3a Port A data inputs 1.0/1.0 20µA/0.6mA I0b – I3b Port B data inputs 1.0/1.0 20µA/0.6mA S0, S1 Common Select inputs 1.0/1.0 20µA/0.6mA Ea Port A Enable input (active Low) 1.0/1.0 20µA/0.6mA Eb Port B Enable input (active Low) 1.0/1.0 20µA/0.6mA Ya, Yb Port A, B data outputs 50/33 1.0µA/20mA NOTE: One (1.0) FAST unit load is defined as: 20µA in the High state and 0.6mA in the Low state. LOGIC SYMBOL Ya VCC = Pin 16 GND = Pin 8 Ea Eb I1a I2a SF00147 I3aI0a Yb I1b I2b 12 13 I3bI0b 10 11 IEC/IEEE SYMBOL SF00148 EN 14 0 2 1 G 0 MUX 11 9
Philips Semiconductors Product specification 74F153Dual 4-line to 1-line multiplexer
1996 Jan 05 3
1 6543 21 4 1 0 1 1 1 2 1 3 1 5 VCC = Pin 16 GND = Pin 8 Ea EbI0a I1a I2a I3a S1 S2 I0b I0b I2b I3b SF00149A FUNCTION TABLE INPUTS OUTPUT S0 S1 En I0n I1n I2n I3n Yn X X H X X X X L L L L L X X X L L L L H X X X H H L L X L X X L H L L X H X X H L H L X X L X L L H L X X H X H H H L X X X L L H H L X X X H H H = High voltage level L = Low voltage level X = Don’t care
Philips Semiconductors Product specification 74F153Dual 4-line to 1-line multiplexer
1996 Jan 05 4
(Operation beyond the limits set forth in this table may impair the useful life of the device. Unless otherwise noted these limits are over the operating free-air temperature range.) SYMBOL PARAMETER RATING UNIT VCC Supply voltage –0.5 to +7.0 V VIN Input voltage –0.5 to +7.0 V IIN Input current –30 to +5 mA VOUT Voltage applied to output in High output state –0.5 to VCC V IOUT Current applied to output in Low output state 40 mA Tamb Operating free-air temperature range 0 to +70 °C Tstg Storage temperature range –65 to +150 °C RECOMMENDED OPERATING CONDITIONS SYMBOL PARAMETER LIMITS UNITSYMBOL PARAMETER MIN NOM MAX UNIT VCC Supply voltage 4.5 5.0 5.5 V VIH High-level input voltage 2.0 V VIL Low-level input voltage 0.8 V IIK Input clamp current –18 mA IOH High-level output current –1 mA IOL Low-level output current 20 mA Tamb Operating free-air temperature range 0 +70 °C DC ELECTRICAL CHARACTERISTICS (Over recommended operating free-air temperature range unless otherwise noted.) SYMBOL PARAMETER TEST CONDITIONS 1 LIMITS UNITSYMBOL PARAMETER TEST CONDITIONS 1 MIN TYP 2 MAX UNIT VO High level output voltage VCC = MIN, VIL = MAX ±10%V CC 2.5 VVOH High-level output voltage VIH = MIN, IOH = MAX ±5%V CC 2.7 3.4 V VO Low level output voltage VCC = MIN, VIL = MAX ±10%V CC 0.30 0.50 VVOL Low-level output voltage VIH = MIN, IOL = MAX ±5%V CC 0.30 0.50 V VIK Input clamp voltage VCC = MIN, II = IIK –0.73 –1.2 V II Input current at maximum input voltageVCC = MAX, VI = 7.0V 100 µA IIH High-level input current VCC = MAX, VI = 2.7V 20 µA IIL Low-level input current VCC = MAX, VI = 0.5V –0.6 mA IOS Short-circuit output current3 VCC = MAX –60 –150 mA ICC Supply current (total) ICCH VCC = MAX En = GND, Sn=In=4.5V 12 20 mA CC y( ) ICCL CC En=Sn=In=GND 12 20 mA NOTES: 1. For conditions shown as MIN or MAX, use the appropriate value specified under recommended operating conditions for the applicable type. 2. All typical values are at VCC = 5V, Tamb = 25°C. 3. Not more than one output should be shorted at a time. For testing IOS , the use of high-speed test apparatus and/or sample-and-hold techniques are preferable in order to minimize internal heating and more accurately reflect operational values. Otherwise, prolonged shorting of a High output may raise the chip temperature well above normal and thereby cause invalid readings in other parameter tests. In any sequence of parameter tests, IOS tests should be performed last.
Philips Semiconductors Product specification 74F153Dual 4-line to 1-line multiplexer
1996 Jan 05 5
AC ELECTRICAL CHARACTERISTICS LIMITS SYMBOL PARAMETER TEST CONDITION VCC = +5.0V Tamb = +25°C C L = 50pF, RL = 500Ω VCC = +5.0V ± 10% Tamb = 0°C to +70°C C L = 50pF, RL = 500Ω UNIT MIN TYP MAX MIN MAX tPLH tPHL Propagation delay In to Yn Waveform 1 3.0 3.0 4.5 5.0 7.0 7.5 2.5 2.5 8.0 8.0 ns tPLH tPHL Propagation delay Sn to Yn Waveform 2 5.0 5.0 8.0 8.0 10.5 10.5 4.5 4.5 12.0 12.0 ns tPLH tPHL Propagation delay E n to Yn Waveform 2 5.0 4.0 7.5 5.5 9.0 7.0 4.5 3.5 10.5 8.0 ns AC WAVEFORMS For all waveforms, VM = 1.5V. VMVM VMVM Yn In tPLH tPHL SF00150 Waveform 1. Propagation Delay, Data to Output VMVM VMVM Yn Sn tPHL tPLH SF00151 En Waveform 2. Propagation Delay, Enable and Select to Output TEST CIRCUIT AND WAVEFORMS tw 90% VM 10% 90% VM 10% 90% VM 10% 90% VM 10% NEGATIVE PULSE POSITIVE PULSE tw AMP (V) tTHL (tf ) INPUT PULSE REQUIREMENTS rep. rate tw tTLH tTHL 1MHz 500ns 2.5ns 2.5ns Input Pulse Definition VCC family 74F D.U.T.PULSE GENERATOR R LC LR T VIN VOUT Test Circuit for Totem-Pole Outputs DEFINITIONS: R L = Load resistor; see AC ELECTRICAL CHARACTERISTICS for value. C L = Load capacitance includes jig and probe capacitance; see AC ELECTRICAL CHARACTERISTICS for value. R T = Termination resistance should be equal to ZOUT of pulse generators. tTHL (tf ) tTLH (tr ) tTLH (tr ) AMP (V) amplitude 3.0V 1.5V VM SF00006
Philips Semiconductors Product specification 74F153Dual 4-line to 1-line multiplexer
1996 Jan 05 6
DIP16: plastic dual in-line package; 16 leads (300 mil) SOT38-4
Philips Semiconductors Product specification 74F153Dual 4-line to 1-line multiplexer
1996 Jan 05 7
SO16: plastic small outline package; 16 leads; body width 3.9 mm SOT109-1
Philips Semiconductors Product specification 74F153Dual 4-line to 1-line multiplexer
1996 Jan 05 8
Short-form specification — The data in a short-form specification is extracted from a full data sheet with the same type number and title. For detailed information see the relevant data sheet or data handbook. Limiting values definition — Limiting values given are in accordance with the Absolute Maximum Rating System (IEC 134). Stress above one or more of the limiting values may cause permanent damage to the device. These are stress ratings only and operation of the device at these or at any other conditions above those given in the Characteristics sections of the specification is not implied. Exposure to limiting values for extended periods may affect device reliability. Application information — Applications that are described herein for any of these products are for illustrative purposes only. Philips Semiconductors make no representation or warranty that such applications will be suitable for the specified use without further testing or modification. Disclaimers Life support — These products are not designed for use in life support appliances, devices or systems where malfunction of these products can reasonably be expected to result in personal injury. Philips Semiconductors customers using or selling these products for use in such applications do so at their own risk and agree to fully indemnify Philips Semiconductors for any damages resulting from such application. Right to make changes — Philips Semiconductors reserves the right to make changes, without notice, in the products, including circuits, standard cells, and/or software, described or contained herein in order to improve design and/or performance. Philips Semiconductors assumes no responsibility or liability for the use of any of these products, conveys no license or title under any patent, copyright, or mask work right to these products, and makes no representations or warranties that these products are free from patent, copyright, or mask work right infringement, unless otherwise specified. Philips Semiconductors
811 East Arques Avenue
P.O. Box 3409 Sunnyvale, California 94088–3409 Telephone 800-234-7381 Copyright Philips Electronics North America Corporation 1998 All rights reserved. Printed in U.S.A. Date of release: 03-98 Document order number: 9397-750-05081 /C0109 /C0110 /C0114 Data sheet status Objective specification Preliminary specification Product specification Product status Development Qualification Production Definition [1] This data sheet contains the design target or goal specifications for product development. Specification may change in any manner without notice. This data sheet contains preliminary data, and supplementary data will be published at a later date. Philips Semiconductors reserves the right to make chages at any time without notice in order to improve design and supply the best possible product. This data sheet contains final specifications. Philips Semiconductors reserves the right to make changes at any time without notice in order to improve design and supply the best possible product. Data sheet status [1] Please consult the most recently issued datasheet before initiating or completing a design.