74F151A PHILIPS | Alldatasheet

Document overview

  • Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
  • PDF pages: 10

Technical content

/C0109 /C0110 /C0114 74F151A 8-input multiplexer Product specification Supercedes data of 1989 Mar 03 IC15 Data Handbook

1995 Jul 17

Philips Semiconductors Product specification 74F151A8-input multiplexer

21995 Jul 17 853–1158 15459

FEATURES

  • High speed 8-to-1 multiplexing
  • On chip decoding
  • Multifunction capability
  • Complementary outputs

DESCRIPTION

The 74F151A is a logic implementation of a single-pole, 8-position switch with the switch position controlled by the state of three Select (S0, S1, S2) inputs. True (Y) and complementary (Y) outputs are both provided. The Enable input (E) is active Low. When E is High, the Y output is High and the Y output is Low, regardless of all other inputs. In one package the 74F151A provides the ability to select from eight sources of data or control information. The device can provide any logic function of four variables and the negation with correct manipulation. PIN CONFIGURATION 107 E VCC Y Y 98GND S2 SF00742 TYPE TYPICAL PROPAGATION DELAY TYPICAL SUPPLY CURRENT (TOTAL) 74F151A 4.5ns 17mA

ORDERING INFORMATION

DESCRIPTION COMMERCIAL RANGE VCC = 5V ±10%, Tamb = 0°C to +70°C PKG DWG # 16-pin plastic DIP N74F151AN SOT38-4 16-pin plastic SO N74F151AD SOT109-1 INPUT AND OUTPUT LOADING AND FAN-OUT TABLE PINS DESCRIPTION 74F (U.L.) HIGH/LOW LOAD VALUE HIGH/LOW I0–I7 Data inputs 1.0/1.0 20µA/0.6mA S0–S2 Select inputs 1.0/1.0 20µA/0.6mA E Enable input (active High) 1.0/1.0 20µA/0.6mA Y, Y Data outputs 150/33 3mA/20mA NOTE: One (1.0) FAST unit load is defined as: 20µA in the High state and 0.6mA in the Low state.

Philips Semiconductors Product specification 74F151A8-input multiplexer

1995 Jul 17 3

VCC = Pin 16 GND = Pin 8 SF00743 4 12131415 E YY I0 I1 I2 I3 I4 I5 I6 I7 IEC/IEEE SYMBOL SF00744 MUX7 G 0 EN LOGIC DIAGRAM VCC = Pin 16 GND = Pin 8 SF00741 YY 4 3 2 1 15 14 13 12 I0 I1 I2 I3 I4 I5 I6 I7 E

Philips Semiconductors Product specification 74F151A8-input multiplexer

1995 Jul 17 4

NOTES: H = High voltage level L = Low voltage level X = Don’t care ABSOLUTE MAXIMUM RATINGS (Operation beyond the limit set forth in this table may impair the useful life of the device. Unless otherwise noted these limits are over the operating free air temperature range.) SYMBOL PARAMETER RATING UNIT VCC Supply voltage –0.5 to +7.0 V VIN Input voltage –0.5 to +7.0 V IIN Input current –30 to +5 mA VOUT Voltage applied to output in High output state –0.5 to VCC V IOUT Current applied to output in Low output state 40 mA Tamb Operating free-air temperature range 0 to +70 °C Tstg Storage temperature –65 to +150 °C RECOMMENDED OPERATING CONDITIONS SYMBOL PARAMETER LIMITS UNITSYMBOL PARAMETER MIN NOM MAX UNIT VCC Supply voltage 4.5 5.0 5.5 V VIH High-level input voltage 2.0 V VIL Low-level input voltage 0.8 V IIK Input clamp current –18 mA IOH High-level output current –1 mA IOL Low-level output current 20 mA Tamb Operating free-air temperature range 0 +70 °C

Philips Semiconductors Product specification 74F151A8-input multiplexer

1995 Jul 17 5

DC ELECTRICAL CHARACTERISTICS (Over recommended operating free-air temperature range unless otherwise noted.) NO TAG LIMITS SYMBOL PARAMETER\\ TEST CONDITIONS NO TAG MIN TYP NO TAG MAX UNIT VO High level output voltage VCC = MIN, VIL = MAX, ±10%V CC 2.5 V VOH High-level output voltage CC , IL , VIH = MIN, IOH = MAX ±5%V CC 2.7 3.4 V VO Low level output voltage VCC = MIN, VIL = MAX, ±10%V CC 0.30 0.50 V VOL Low-level output voltage CC , IL , VIH = MIN, IOL = MAX ±5%V CC 0.30 0.50 V VIK Input clamp voltage VCC = MIN, II = IIK –0.73 –1.2 V II Input current at maximum input voltage VCC = MAX, VI = 7.0V 100 µA IIH High-level input current VCC = MAX, VI = 2.7V 20 µA IIL Low-level input current VCC = MAX, VI = 0.5V –0.6 mA IOS Short-circuit output currentNO TAG VCC = MAX –60 –150 mA ICC Supply current (total) ICCH VCC = MAX 18 25 mA ICC Supply current (total) ICCL VCC = MAX 17 25 mA NOTES: 1. For conditions shown as MIN or MAX, use the appropriate value specified under recommended operating conditions for the applicable type. 2. All typical values are at VCC = 5V, Tamb = 25°C. 3. Not more than one output should be shorted at a time. For testing IOS , the use of high-speed test apparatus and/or sample-and-hold techniques are preferable in order to minimize internal heating and more accurately reflect operational values. Otherwise, prolonged shorting of a High output may raise the chip temperature well above normal and thereby cause invalid readings in other parameter tests. In any sequence of parameter tests, IOS tests should be performed last. AC ELECTRICAL CHARACTERISTICS LIMITS SYMBOL PARAMETER TEST CONDITION VCC = +5.0V Tamb = +25°C C L = 50pF R L = 500Ω VCC = +5.0V ± 10% Tamb = 0°C to +70°C C L = 50pF R L = 500Ω UNIT MIN TYP MAX MIN MAX tPLH tPHL Propagation delay In to Y Waveform NO TAG 2.5 2.5 4.5 4.5 7.0 7.0 2.5 2.5 7.5 7.5 ns tPLH tPHL Propagation delay In to Y Waveform NO TAG 2.0 1.0 4.0 2.0 7.0 4.5 2.0 1.0 7.5 5.0 ns tPLH tPHL Propagation delay Sn to Y Waveform 1, 2 4.5 4.0 6.5 6.0 10.0 8.5 4.0 3.5 11.0 9.5 ns tPLH tPHL Propagation delay Sn to Y Waveform NO TAG, NO TAG 3.5 2.5 5.5 4.5 8.5 7.0 3.0 2.0 9.5 7.5 ns tPLH tPHL Propagation delay E to Y Waveform 1 4.0 3.0 6.5 5.0 9.0 7.0 3.5 3.0 9.5 7.5 ns tPLH tPHL Propagation delay E to Y Waveform NO TAG 2.5 2.0 4.5 3.5 6.5 5.5 2.5 1.5 7.0 6.0 ns AC WAVEFORMS For all waveforms, VM = 1.5V

Philips Semiconductors Product specification 74F151A8-input multiplexer

1995 Jul 17 6

Waveform 1. For Inverting Outputs VMVM VMVM VOUT VIN tPLH tPHL SF00092 Waveform 2. For Non-Inverting Outputs TEST CIRCUIT AND WAVEFORMS tw 90% VM 10% 90% VM 10% 90% VM 10% 90% VM 10% NEGATIVE PULSE POSITIVE PULSE tw AMP (V) tTHL (tf ) INPUT PULSE REQUIREMENTS rep. rate tw tTLH tTHL 1MHz 500ns 2.5ns 2.5ns Input Pulse Definition VCC family 74F D.U.T.PULSE GENERATOR R LC LR T VIN VOUT Test Circuit for Totem-Pole Outputs DEFINITIONS: R L = Load resistor; see AC ELECTRICAL CHARACTERISTICS for value. C L = Load capacitance includes jig and probe capacitance; see AC ELECTRICAL CHARACTERISTICS for value. R T = Termination resistance should be equal to ZOUT of pulse generators. tTHL (tf ) tTLH (tr ) tTLH (tr ) AMP (V) amplitude 3.0V 1.5V VM SF00006

Philips Semiconductors Product specification 74F151A8-input multiplexer

1995 Jul 17 7

DIP16: plastic dual in-line package; 16 leads (300 mil) SOT38-4

Philips Semiconductors Product specification 74F151A8-input multiplexer

1995 Jul 17 8

SO16: plastic small outline package; 16 leads; body width 3.9 mm SOT109-1

Philips Semiconductors Product specification 74F151A8-input multiplexer

1995 Jul 17 9

Philips Semiconductors Product specification 74F151A8-input multiplexer yyyy mmm dd 10 Definitions Short-form specification — The data in a short-form specification is extracted from a full data sheet with the same type number and title. For detailed information see the relevant data sheet or data handbook. Limiting values definition — Limiting values given are in accordance with the Absolute Maximum Rating System (IEC 134). Stress above one or more of the limiting values may cause permanent damage to the device. These are stress ratings only and operation of the device at these or at any other conditions above those given in the Characteristics sections of the specification is not implied. Exposure to limiting values for extended periods may affect device reliability. Application information — Applications that are described herein for any of these products are for illustrative purposes only. Philips Semiconductors make no representation or warranty that such applications will be suitable for the specified use without further testing or modification. Disclaimers Life support — These products are not designed for use in life support appliances, devices or systems where malfunction of these products can reasonably be expected to result in personal injury. Philips Semiconductors customers using or selling these products for use in such applications do so at their own risk and agree to fully indemnify Philips Semiconductors for any damages resulting from such application. Right to make changes — Philips Semiconductors reserves the right to make changes, without notice, in the products, including circuits, standard cells, and/or software, described or contained herein in order to improve design and/or performance. Philips Semiconductors assumes no responsibility or liability for the use of any of these products, conveys no license or title under any patent, copyright, or mask work right to these products, and makes no representations or warranties that these products are free from patent, copyright, or mask work right infringement, unless otherwise specified. Philips Semiconductors

811 East Arques Avenue

P.O. Box 3409 Sunnyvale, California 94088–3409 Telephone 800-234-7381  Copyright Philips Electronics North America Corporation 1998 All rights reserved. Printed in U.S.A. print code Date of release: 10-98 Document order number: 9397-750-05079 /C0109 /C0110 /C0114 Data sheet status Objective specification Preliminary specification Product specification Product status Development Qualification Production Definition [1] This data sheet contains the design target or goal specifications for product development. Specification may change in any manner without notice. This data sheet contains preliminary data, and supplementary data will be published at a later date. Philips Semiconductors reserves the right to make chages at any time without notice in order to improve design and supply the best possible product. This data sheet contains final specifications. Philips Semiconductors reserves the right to make changes at any time without notice in order to improve design and supply the best possible product. Data sheet status [1] Please consult the most recently issued datasheet before initiating or completing a design.