74F138

74F138 PHILIPS | Alldatasheet

Document overview

• Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
• PDF pages: 8

Technical content

/C0109 /C0110 /C0114 74F138 1-of-8 decoder/demultiplexer Product specification IC15 Data Handbook

1991 Feb 14

Philips Semiconductors Product specification 74F1381-of-8 decoder/demultiplexer 2February 14, 1991 853–0343 01719 FEATURE

• Demultiplexing capability
• Multiple input enable for easy expansion
• Ideal for memory chip select decoding
• Industrial temperature range available (–40°C to +85°C)

DESCRIPTION

The 74F138 decoder accepts three binary weighted inputs (A0, A1, A2) and when enabled, provides eight mutually exclusive, active low outputs (Q0 – Q7). The device features three enable inputs; two active low (E0, E1) and one active high (E2). Every output will be high unless E0 and E1 are low and E2 is high. This multiple enable function allows easy parallel expansion of the device to 1-of-32 (5 lines to 32 lines) decoder with just four 74F138s and one inverter (see Figure 1). The device can be used as an eight output demultiplexer by using one of the active low enable inputs as the data input and the remaining enable inputs as strobes. Enable inputs not used must be permanently tied to their appropriate active high or active low state. PIN CONFIGURATION 107 Q 7 VCC Q 3 Q 4 Q 5 Q 2 Q 0 Q 1 98GND Q 6 SF00174 TYPE TYPICAL PROPAGATION DELAY TYPICAL SUPPLY CURRENT (TOTAL) 74F138 5.8ns 13mA

ORDERING INFORMATION

DESCRIPTION COMMERCIAL RANGE VCC = 5V ±10%, Tamb = 0°C to +70°C INDUSTRIAL RANGE VCC = 5V ±10%, Tamb = –40°C to +85°C PKG DWG # 16-pin plastic DIP N74F138N I74F138N SOT38-4 16-pin plastic SO N74F138D I74F138D SOT109-1 INPUT AND OUTPUT LOADING AND FAN-OUT TABLE PINS DESCRIPTION 74F (U.L.) HIGH/LOW LOAD VALUE HIGH/LOW A0 – A2 Address inputs 1.0/1.0 20µA/0.6mA E0, E1 Enable inputs (active Low) 1.0/1.0 20µA/0.6mA E2 Enable input (active High) 1.0/1.0 20µA/0.6mA Q 0 – Q7 Data outputs 50/33 1.0mA/20mA NOTE: One (1.0) FAST unit load is defined as: 20µA in the High state and 0.6mA in the Low state. LOGIC SYMBOL A1 A2A0 Q2 Q3 Q4 Q5 13 12 11 10 12 3 VCC = Pin 16 GND = Pin 8 SF00175 IEC/IEEE SYMBOL SF00176 DMUX1 0 0 G 0

Philips Semiconductors Product specification 74F1381-of-8 decoder/demultiplexer February 14, 1991 3 LOGIC DIAGRAM 15 14 13 12 11 10 9 7 Q 0Q 1Q 2Q 3Q 4Q 5Q 6Q 7 VCC = Pin 16 GND = Pin 8 SF00177 FUNCTION TABLE INPUTS OUTPUTS E0 E1 E2 A0 A1 A2 Q 0 Q 1 Q 2 Q 3 Q 4 Q 5 Q 6 Q7 H X X X X X H H H H H H H H X H X X X X H H H H H H H H X X L X X X H H H H H H H H L L H L L L L H H H H H H H L L H H L L H L H H H H H H L L H L H L H H L H H H H H L L H H H L H H H L H H H H L L H L L H H H H H L H H H L L H H L H H H H H H L H H L L H L H H H H H H H H L H L L H H H H H H H H H H H L NOTES: H = High voltage level L = Low voltage level X = Don’t care APPLICATION SF00178 Q0 Q1 Q2 Q3 Q4 Q5 Q6 Q7 A0 A1 A2E2 E0 74F138 Q0 Q1 Q2 Q3 Q4 Q5 Q6 Q7 A0 A1 A2E2 E0 74F138 Q0 Q1 Q2 Q3 Q4 Q5 Q6 Q7 A0 A1 A2E2 E0 74F138 Q0 Q1 Q2 Q3 Q4 Q5 Q6 Q7 A0 A1 A2E2 E0 74F138 74F04 Q31Q0 H Figure 1. Expansion of 1-of-8 Decoding

Philips Semiconductors Product specification 74F1381-of-8 decoder/demultiplexer February 14, 1991 4 ABSOLUTE MAXIMUM RATINGS (Operation beyond the limit set forth in this table may impair the useful life of the device. Unless otherwise noted these limits are over the operating free air temperature range.) SYMBOL PARAMETER RATING UNIT VCC Supply voltage –0.5 to +7.0 V VIN Input voltage –0.5 to +7.0 V IIN Input current –30 to +5 mA VOUT Voltage applied to output in High output state –0.5 to VCC V IOUT Current applied to output in Low output state 40 mA T O perating free air temperature range Commercial range 0 to +70 °C Tamb Operating free-air temperature range Industrial range –40 to +85 °C Tstg Storage temperature range –65 to +150 °C RECOMMENDED OPERATING CONDITIONS SYMBOL PARAMETER LIMITS UNITSYMBOL PARAMETER MIN NOM MAX UNIT VCC Supply voltage 4.5 5.0 5.5 V VIH High-level input voltage 2.0 V VIL Low-level input voltage 0.8 V IIK Input clamp current –18 mA IOH High-level output current –1 mA IOL Low-level output current 20 mA T b O perating free-air temperature range Commercial range 0 +70 °C Tamb O erating free-air tem erature range Industrial range –40 +85 °C DC ELECTRICAL CHARACTERISTICS (Over recommended operating free-air temperature range unless otherwise noted.) SYMBOL PARAMETER TEST CONDITIONS 1 LIMITS UNITSYMBOL PARAMETER TEST CONDITIONS 1 MIN TYP 2 MAX UNIT VO High level output voltage VCC = MIN, VIL = MAX, IO = MAX ±10%V CC 2.5 V VOH High-level output voltage CC , IL , VIH = MIN IOH = MAX ±5%V CC 2.7 3.4 V VO Low level output voltage VCC = MIN, VIL = MAX, IO = MAX ±10%V CC 0.30 0.50 V VOL Low-level output voltage CC , IL , VIH = MIN IOL = MAX ±5%V CC 0.30 0.50 V VIK Input clamp voltage VCC = MIN, II = IIK –0.73 –1.2 V II Input current at maximum input voltageVCC = MAX, VI = 7.0V 100 µA IIH High-level input current VCC = MAX, VI = 2.7V 20 µA IIL Low-level input current VCC = MAX, VI = 0.5V –0.6 mA IOS Short-circuit output current3 VCC = MAX –60 –150 mA ICC Supply current4 (total) VCC = MAX 13 20 mA NOTES: 1. For conditions shown as MIN or MAX, use the appropriate value specified under recommended operating conditions for the applicable type. 2. All typical values are at VCC = 5V, Tamb = 25°C. 3. Not more than one output should be shorted at a time. For testing IOS , the use of high-speed test apparatus and/or sample-and-hold techniques are preferable in order to minimize internal heating and more accurately reflect operational values. Otherwise, prolonged shorting of a high output may raise the chip temperature well above normal and thereby cause invalid readings in other parameter tests. In any sequence of parameter tests, IOS tests should be performed last. 4. Measure ICC , outputs must be open, VIN on all inputs = 4.5V.

Philips Semiconductors Product specification 74F1381-of-8 decoder/demultiplexer February 14, 1991 5 AC ELECTRICAL CHARACTERISTICS LIMITS SYMBOL PARAMETER TEST CONDITION VCC = +5.0V Tamb = +25°C C L = 50pF R L = 500Ω VCC = +5.0V ± 10% Tamb = 0°C to +70°C C L = 50pF R L = 500Ω VCC = +5.0V ± 10% Tamb = –40°C to +85°C C L = 50pF R L = 500Ω UNIT MIN TYP MAX MIN MAX MIN MAX tPLH tPHL Propagation delay An to Qn Waveform 1, 2 3.5 4.0 5.6 6.1 7.0 8.0 3.5 4.0 8.0 9.0 3.0 3.5 8.5 9.0 ns tPLH tPHL Propagation delay E 0 or E1 to Qn Waveform 2 3.5 3.0 6.4 5.3 7.0 7.0 3.5 3.0 8.0 7.5 3.0 3.0 8.0 7.5 ns tPLH tPHL Propagation delay to Qn Waveform 1 4.0 3.5 6.2 5.6 8.0 7.5 4.0 3.5 9.0 8.5 4.0 3.5 9.5 8.5 ns AC WAVEFORMS For all waveforms, VM = 1.5V VMVM VMVM Q n An, E2 tPHL tPLH SF00179 Waveform 1. Propagation Delay for Inverting Outputs VMVM VMVM Q n An, E0, E1 tPHL tPLH SF00180 Waveform 2. Propagation Delay for Non-Inverting Outputs TEST CIRCUIT AND WAVEFORMS tw 90% VM 10% 90% VM 10% 90% VM 10% 90% VM 10% NEGATIVE PULSE POSITIVE PULSE tw AMP (V) tTHL (tf ) INPUT PULSE REQUIREMENTS rep. rate tw tTLH tTHL 1MHz 500ns 2.5ns 2.5ns Input Pulse Definition VCC family 74F D.U.T.PULSE GENERATOR R LC LR T VIN VOUT Test Circuit for Totem-Pole Outputs DEFINITIONS: R L = Load resistor; see AC ELECTRICAL CHARACTERISTICS for value. C L = Load capacitance includes jig and probe capacitance; see AC ELECTRICAL CHARACTERISTICS for value. R T = Termination resistance should be equal to ZOUT of pulse generators. tTHL (tf ) tTLH (tr ) tTLH (tr ) AMP (V) amplitude 3.0V 1.5V VM SF00006

Philips Semiconductors Product specification 74F1381-of-8 decoder/demultiplexer

1991 Feb 14 6

DIP16: plastic dual in-line package; 16 leads (300 mil) SOT38-4

Philips Semiconductors Product specification 74F1381-of-8 decoder/demultiplexer

1991 Feb 14 7

SO16: plastic small outline package; 16 leads; body width 3.9 mm SOT109-1

Philips Semiconductors Product specification 74F1381-of-8 decoder/demultiplexer yyyy mmm dd 8 Definitions Short-form specification — The data in a short-form specification is extracted from a full data sheet with the same type number and title. For detailed information see the relevant data sheet or data handbook. Limiting values definition — Limiting values given are in accordance with the Absolute Maximum Rating System (IEC 134). Stress above one or more of the limiting values may cause permanent damage to the device. These are stress ratings only and operation of the device at these or at any other conditions above those given in the Characteristics sections of the specification is not implied. Exposure to limiting values for extended periods may affect device reliability. Application information — Applications that are described herein for any of these products are for illustrative purposes only. Philips Semiconductors make no representation or warranty that such applications will be suitable for the specified use without further testing or modification. Disclaimers Life support — These products are not designed for use in life support appliances, devices or systems where malfunction of these products can reasonably be expected to result in personal injury. Philips Semiconductors customers using or selling these products for use in such applications do so at their own risk and agree to fully indemnify Philips Semiconductors for any damages resulting from such application. Right to make changes — Philips Semiconductors reserves the right to make changes, without notice, in the products, including circuits, standard cells, and/or software, described or contained herein in order to improve design and/or performance. Philips Semiconductors assumes no responsibility or liability for the use of any of these products, conveys no license or title under any patent, copyright, or mask work right to these products, and makes no representations or warranties that these products are free from patent, copyright, or mask work right infringement, unless otherwise specified. Philips Semiconductors

811 East Arques Avenue

P.O. Box 3409 Sunnyvale, California 94088–3409 Telephone 800-234-7381  Copyright Philips Electronics North America Corporation 1998 All rights reserved. Printed in U.S.A. print code Date of release: 10-98 Document order number: 9397-750-05076 /C0109 /C0110 /C0114 Data sheet status Objective specification Preliminary specification Product specification Product status Development Qualification Production Definition [1] This data sheet contains the design target or goal specifications for product development. Specification may change in any manner without notice. This data sheet contains preliminary data, and supplementary data will be published at a later date. Philips Semiconductors reserves the right to make chages at any time without notice in order to improve design and supply the best possible product. This data sheet contains final specifications. Philips Semiconductors reserves the right to make changes at any time without notice in order to improve design and supply the best possible product. Data sheet status [1] Please consult the most recently issued datasheet before initiating or completing a design.