74AUP1G04GF | DigiCamel IC Datasheet

Online Datasheet

Read 74AUP1G04GF online.

74AUP1G04 PHILIPS | Alldatasheet

Document overview

Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
PDF pages: 16

Technical content

General description The 74AUP1G04 is a high-performance, low-power, low-voltage, Si-gate CMOS device, superior to most advanced CMOS compatible TTL families. Schmitt-trigger action at all inputs makes the circuit tolerant to slower input rise and fall times across the entire VCC range from 0.8 V to 3.6 V. This device ensures a very low static and dynamic power consumption across the entire VCC range from 0.8 V to 3.6 V. This device is fully speciﬁed for partial Power-down applications using IOFF . The IOFF circuitry disables the output, preventing the damaging backﬂow current through the device when it is powered down. The 74AUP1G04 provides the single inverting buffer. 2. Features ■ Wide supply voltage range from 0.8 V to 3.6 V ■ High noise immunity ■ Complies with JEDEC standards: ◆ JESD8-12 (0.8 V to 1.3 V) ◆ JESD8-11 (0.9 V to 1.65 V) ◆ JESD8-7 (1.2 V to 1.95 V) ◆ JESD8-5 (1.8 V to 2.7 V) ◆ JESD8-B (2.7 V to 3.6 V) ■ ESD protection: ◆ HBM JESD22-A114-C Class 3A. Exceeds 5000 V ◆ MM JESD22-A115-A exceeds 200 V ◆ CDM JESD22-C101-C exceeds 1000 V ■ Low static power consumption; ICC = 0.9µA (maximum) ■ Latch-up performance exceeds 100 mA per JESD 78 Class II ■ Inputs accept voltages up to 3.6 V ■ Low noise overshoot and undershoot < 10 % of VCC ■ IOFF circuitry provides partial Power-down mode operation ■ Multiple package options ■ Speciﬁed from−40 °Ct o+ 8 5°C and −40 °C to +125°C 74AUP1G04 Low-power inverter Rev. 02 — 28 June 2006 Product data sheet

6.1 Pinning

Table 1. Ordering information Table 2. Marking

6.2 Pin description

[1] The minimum input and output voltage ratings may be exceeded if the input and output current ratings are observed. [2] For TSSOP5 packages: above 87.5°C the value of Ptotderates linearly with 4.0 mW/K. For XSON6 packages: above 45°C the value of Ptotderates linearly with 2.4 mW/K. Table 3. Pin description Table 4. Function table[1] Table 5. Limiting values In accordance with the Absolute Maximum Rating System (IEC 60134). Voltages are referenced to GND (ground = 0 V).

Recommended operating conditions

Table 6. Recommended operating conditions Table 7. Static characteristics At recommended operating conditions; voltages are referenced to GND (ground = 0 V).

74AUP1G04_2 © Koninklijke Philips Electronics N.V. 2006. All rights reserved. Table 7. Static characteristics …continued At recommended operating conditions; voltages are referenced to GND (ground = 0 V).

74AUP1G04_2 © Koninklijke Philips Electronics N.V. 2006. All rights reserved. [1] All typical values are measured at nominal VCC . [2] C PD is used to determine the dynamic power dissipation (PD inµW). L × VCC 2 × fo) = sum of the outputs. Table 8. Dynamic characteristics …continued Table 9. Dynamic characteristics

74AUP1G04_2 © Koninklijke Philips Electronics N.V. 2006. All rights reserved. Table 9. Dynamic characteristics …continued Measurement points are given inTable10. Logic levels: VOL and VOH are typical output voltage drop that occur with the output load. Table 10. Measurement points

74AUP1G04_2 © Koninklijke Philips Electronics N.V. 2006. All rights reserved. [1] For measuring enable and disable times RL =5k Ω , for measuring propagation delays, setup and hold times and pulse width RL =1M Ω . Test data is given inTable11. VEXT = External voltage for measuring switching times. Table 11. Test data

74AUP1G04_2 © Koninklijke Philips Electronics N.V. 2006. All rights reserved. Product data sheet Rev. 02 — 28 June 2006 11 of 16 Philips Semiconductors 74AUP1G04 Low-power inverter 13. Package outline Fig 9. Package outline SOT353-1 (TSSOP5) UNIT A 1 A max. A 2 A 3 bp LH E Lp wyvce D (1) E(1) Z(1) q REFERENCESOUTLINE VERSION EUROPEAN PROJECTION ISSUE DATE IEC JEDEC JEITA mm 0.1 1.0 0.8 0.30 0.15 0.25 0.08 2.25 1.85 1.35 1.15 0.65 1.3 2.25 2.0 0.60 0.15 0°0.1 0.10.30.425 DIMENSIONS (mm are the original dimensions) Note 1. Plastic or metal protrusions of 0.15 mm maximum per side are not included. 0.46 0.21 SOT353-1 MO-203 SC-88A 00-09-01 03-02-19 w Mbp D Z e 0.15 5 4 q AA2 Lp (A3) detail X L H E E c v M A X A y 1.5 3 mm0 scale TSSOP5: plastic thin shrink small outline package; 5 leads; body width 1.25 mm SOT353-1 1.1

74AUP1G04_2 © Koninklijke Philips Electronics N.V. 2006. All rights reserved. Product data sheet Rev. 02 — 28 June 2006 12 of 16 Philips Semiconductors 74AUP1G04 Low-power inverter Fig 10. Package outline SOT886 (XSON6) terminal 1 index area REFERENCESOUTLINE VERSION EUROPEAN PROJECTION ISSUE DATE IEC JEDEC JEITA SOT886 MO-252 SOT886 04-07-15 04-07-22 DIMENSIONS (mm are the original dimensions) XSON6: plastic extremely thin small outline package; no leads; 6 terminals; body 1 x 1.45 x 0.5 mm D E e A 1 b LL1 0 1 2 mm scale Notes 1. Including plating thickness. 2. Can be visible in some manufacturing processes. UNIT mm 0.25 0.17 1.5 1.4 0.35 0.27 A max b E 1.05 0.95 D ee 1 L 0.40 0.32 0.50.6 A (1) max 0.5 0.04 (2) (2) A

74AUP1G04_2 © Koninklijke Philips Electronics N.V. 2006. All rights reserved. Product data sheet Rev. 02 — 28 June 2006 13 of 16 Philips Semiconductors 74AUP1G04 Low-power inverter Fig 11. Package outline SOT891 (XSON6) terminal 1 index area REFERENCESOUTLINE VERSION EUROPEAN PROJECTION ISSUE DATE IEC JEDEC JEITA SOT891 SOT891 05-03-11 05-04-06 XSON6: plastic extremely thin small outline package; no leads; 6 terminals; body 1 x 1 x 0.5 mm D E e A 1 b LL1 0 1 2 mm scale DIMENSIONS (mm are the original dimensions) UNIT mm 0.20 0.12 1.05 0.95 0.35 0.27 A 1 max b E 1.05 0.95 D ee 1 L 0.40 0.32 0.350.55 A max 0.5 0.04 A

ESD HBM and C PD values modiﬁed inSection2,Table8
Added type number 74AUP1G04GF (XSON6/SOT891) package 74AUP1G04_1 20050718 Product data sheet - -

74AUP1G04_2 © Koninklijke Philips Electronics N.V. 2006. All rights reserved. Product data sheet Rev. 02 — 28 June 2006 15 of 16 Philips Semiconductors 74AUP1G04 Low-power inverter 16. Legal information

16.1 Data sheet status

[1] Please consult the most recently issued document before initiating or completing a design. [2] The term ‘short data sheet’ is explained in section “Deﬁnitions”. [3] The product status of device(s) described in this document may have changed since this document was published and may differ in case of multiple devices. The latest product status information is available on the Internet at URL http://www.semiconductors.philips.com.

16.2 Deﬁnitions

Draft —The document is a draft version only. The content is still under internal review and subject to formal approval, which may result in modiﬁcations or additions. Philips Semiconductors does not give any representations or warranties as to the accuracy or completeness of information included herein and shall have no liability for the consequences of use of such information. Short data sheet —A short data sheet is an extract from a full data sheet with the same product type number(s) and title. A short data sheet is intended for quick reference only and should not be relied upon to contain detailed and full information. For detailed and full information see the relevant full data sheet, which is available on request via the local Philips Semiconductors sales ofﬁce. In case of any inconsistency or conﬂict with the short data sheet, the full data sheet shall prevail.

16.3 Disclaimers

General — Information in this document is believed to be accurate and reliable. However, Philips Semiconductors does not give any representations or warranties, expressed or implied, as to the accuracy or completeness of such information and shall have no liability for the consequences of use of such information. Right to make changes —Philips Semiconductors reserves the right to make changes to information published in this document, including without limitation speciﬁcations and product descriptions, at any time and without notice. This document supersedes and replaces all information supplied prior to the publication hereof. Suitability for use —Philips Semiconductors products are not designed, authorized or warranted to be suitable for use in medical, military, aircraft, space or life support equipment, nor in applications where failure or malfunction of a Philips Semiconductors product can reasonably be expected to result in personal injury, death or severe property or environmental damage. Philips Semiconductors accepts no liability for inclusion and/or use of Philips Semiconductors products in such equipment or applications and therefore such inclusion and/or use is at the customer’s own risk. Applications —Applications that are described herein for any of these products are for illustrative purposes only. Philips Semiconductors makes no representation or warranty that such applications will be suitable for the speciﬁed use without further testing or modiﬁcation. Limiting values —Stress above one or more limiting values (as deﬁned in the Absolute Maximum Ratings System of IEC 60134) may cause permanent damage to the device. Limiting values are stress ratings only and operation of the device at these or any other conditions above those given in the Characteristics sections of this document is not implied. Exposure to limiting values for extended periods may affect device reliability. Terms and conditions of sale —Philips Semiconductors products are sold subject to the general terms and conditions of commercial sale, as published at http://www.semiconductors.philips.com/proﬁle/terms , including those pertaining to warranty, intellectual property rights infringement and limitation of liability, unless explicitly otherwise agreed to in writing by Philips Semiconductors. In case of any inconsistency or conﬂict between information in this document and such terms and conditions, the latter will prevail. No offer to sell or license —Nothing in this document may be interpreted or construed as an offer to sell products that is open for acceptance or the grant, conveyance or implication of any license under any copyrights, patents or other industrial or intellectual property rights.

16.4 Trademarks

Notice: All referenced brands, product names, service names and trademarks are the property of their respective owners. 17. Contact information For additional information, please visit: http://www.semiconductors.philips.com For sales ofﬁce addresses, send an email to: sales.addresses@www.semiconductors.philips.com Document status[1][2] Product status[3] Deﬁnition Objective [short] data sheet Development This document contains data from the objective speciﬁcation for product development. Preliminary [short] data sheet Qualiﬁcation This document contains data from the preliminary speciﬁcation. Product [short] data sheet Production This document contains the product speciﬁcation.

Philips Semiconductors 74AUP1G04 Low-power inverter © Koninklijke Philips Electronics N.V. 2006. All rights reserved. For more information, please visit: http://www.semiconductors.philips.com. Date of release: 28 June 2006 Document identifier: 74AUP1G04_2 Please be aware that important notices concerning this document and the product(s) described herein, have been included in section ‘Legal information’. 18. Contents

Product Information

74AUP1G04GF specifications and overview.

Summary

Low-power inverter Rev. 02-28 June 2006

Description

Low-power inverter Rev. 02-28 June 2006

Source title 74AUP1G04GF Datasheet(PDF) - NXP Semiconductors

Related Parts

More parts from the same family.

Browse manufacturer