7200DL 3M | Alldatasheet

Document overview

  • Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
  • PDF pages: 4

Technical content

3M™ Novec™ 7200DL Engineered Fluid is a high purity version of 3M™ Novec™ 7200 Engineered Fluid introduced to meet the demanding needs of the disk drive industry. Product specifications are tightly controlled for the following:

  • ions • metals
  • particulate • non-volatile residue Novec 7200DL fluid is used by the disk drive industry for the deposition of lubricants and lubricant additives onto hard disk media as well as for cleaning during the processing of head gimbal assemblies. It is also used in other electronics and in medical industry applications that require a high purity and consistent product. 3M™ Novec™ 7200DL Engineered Fluid Product Information Typical Physical Properties Environmental and Safety Properties Properties 3M™ Novec™ 7200DL Engineered Fluid Molecular Weight 264 Boiling Point (°C) 76 Freeze Point (°C) -138 Liquid Density (g/ml) 1.42 Surface Tension (dynes/cm) 13.6 Solubility of Solvent in Water, ppmw <20 Solubility of Water in Solvent, ppmw 92 Vapor Pressure (mmHg) 118 Viscosity (cps) 0.58 Heat of Vaporization (cal/g @ boiling point) 28 Specific Heat (cal/g °C) 0.29 Properties 3M™ Novec™ 7200DL Engineered Fluid Ozone Depletion Potential–ODP1 0.00 Global Warming Potential2 55 Atmospheric Lifetime (years) 0.77 Flash Point None Flammability Range in Air 2.4-12.4% 1 CFC-11=1.0 2 GWP–100 year ITH, CO2 = 1.0 Data compiled from published information. Not for specification purposes. All values @ 25°C unless otherwise specified. Material Description Ingredients 3M™ Novec™ 7200DL Engineered Fluid Ethoxy-nonafluorobutane 99.0% minimum Non-volatile residue (NVR) 1.0 ppm maximum Appearance Clear, colorless

3M™ Novec™ 7200DL Engineered Fluid Typical Purity Specifications Purity Specifications (properties controlled and monitored for 3M ™ Novec™ 7200DL Engineered Fluid, which are not controlled and monitored for ™ Novec™ 7200 Engineered Fluid) Properties Units 3M™ Novec™ 7200DL Engineered Fluid Particulate Levels* >0.3 micron #/ml Monitor** >0.5 micron Monitor >1.0 micron Monitor Ion Concentration* ppb <10.0 Cl- <10.0 NO2 - <10.0 Br - <10.0 NO3 - <10.0 PO4 3- <10.0 SO4 2- <10.0 HCOO- <10.0 CH3COO- Monitor (C2O4)2- Monitor Water* ppm < 50+ ** Non-Volatile Analysis* Hydrocarbons ppb < 200 Silicones None Detected Esters < 30 Metals*** Ag, Al, Ba, Ca, Cd, Co, Cr Cu, Fe, K, Li, Mg, Mn, Na Ni, Pb, Sr, Ti, Zn ppb < 5 Each * Certificate of Analysis specifications Monitor—The values of these qualities are included with the Certificate of Analysis, but do not have specified values by the C of A specifications. * As filled Materials Compatibility 3M™ Novec™ 7200DL Engineered Fluid is compatibile with a wide range of metals, plastics and elastomers– most materials used in electronics manufacturing. As with most fluorinated liquids, Novec 7200DL fluid will absorb into fluorinated plastics and elastomers over longer exposures. Metals Plastics Elastomers Aluminum Acrylic (PMMA) Butyl Rubber* Copper Polyethylene Natural Rubber Carbon Steel Polypropylene EPDM

302 Stainless Steel Polycarbonate EPR

Compatible after one hour exposure at boiling temperature. Exceptions: Some swelling of PTFE and silicone rubber. Some surface oxidation of copper during heat aging. * Butyl Rubber best for extended exposure > one month.

3M will continue to recognize and exercise its responsibility to prevent pollution at the source wherever and whenever possible; develop products that will have a minimal effect on the environment; conserve natural resources through the use of reclamation and other appropriate methods; assure that its facilities and products meet and sustain the regulations of all federal, state and local environmental agencies; assist, wherever possible, governmental agencies and other official organizations engaged in environmental activities. Packaging and Availability 3M™ Novec™ 7200DL Engineered Fluid may be ordered in the following container sizes:

  • 1-gallon pail
  • 5-gallon pail
  • 30-gallon drum Toxicity Profile The toxicological testing completed on Novec 7200DL fluid shows the overall toxicity is low. The material is practically non-irritating to the eyes, minimally irritating to the skin and is not a mutagen. This material is rated “practically non-toxic” through inhalation. Twenty-eight day inhalation studies have helped establish a recommended exposure guideline of 200 ppm for eight-hour average worker exposure per day. Properties 3M™ Novec™ 7200DL Engineered Fluid Acute Lethal Inhalation Concentration >92,000 ppm (4 hour) Oral Practically non-toxic (>5g/kg) Eye Irritation Minimally irritating Skin Irritation Non-irritating Skin Sensitization Not a skin sensitizer Inhalation (28 day study) 200 ppm exposure guideline Detailed results are available. Developmental Toxicity Detailed results are available Mutagenicity Not a mutagen Cardiac Sensitization No signs at exposure up to 20,000 ppm Ecotoxicity Testing Complete–low aquatic toxicity Environmental, Health and Safety Before using this product, please read the current product Material Safety Data Sheet (available through your 3M sales or technical service representative) and the precautionary statement on the product package. Follow all applicable precautions and directions. Handling and Shelf Life Novec 7200DL Engineered Fluid is nonflammable and does not exhibit flammability characteristics under normal operation and storage conditions. The fluid is resistant to thermal breakdown and hydrolysis during storage and use. Recommended handling procedures are provided in the Material Safety Data Sheet, which is available from your local 3M representative upon request or www.3m.com/electronicmaterials When stored at room temperature (20°C) in the original unopened containers, this product has a shelf life of two years from date of shipment. After two years, the product should be retested to verify that it will meet the purity specifications as listed in this document.

3M™ Novec™ 7200DL Engineered Fluid has been accepted for commercial use by regulatory agencies in the components of Novec 7200DL fluid have been nominated to China’s draft chemical inventory. In addition, Novec 7200DL fluid is also available for commercial use in countries that currently do not have chemical inventories, such as Singapore, Mexico and other countries. Contact your local 3M representative regarding the regulatory status of Novec 7200DL fluid in other countries. Novec 7200DL fluid has been approved under the Significant New Alternatives Policy (SNAP) of the U.S. EPA. In addition, Novec 7200DL fluid has been excluded by the U.S. EPA from the definition of a VOC on the basis that this compound has negligible contribution to tropospheric ozone formation. Recycle and Disposal Options Used Fluid Return Program 3M offers a program for free pickup and return of used 3M specialty fluids in the U.S. A pre-negotiated handling agreement between users and our authorized service provider offers users broad protection against future liability for used 3M product. The fluid return program is covered by independent third-party financial and environmental audits of treatment, storage and disposal facilities. Necessary documentation is provided. A minimum of 30 gallons of used 3M specialty fluid is required for participation in this free program. For additional information on the 3M Used Fluid Return Program, contact your local 3M representative or call 3M Customer Service at 800.810.8513. Resources 3M™ Novec™ Engineered Fluids are supported by global sales, technical and customer service resources, with technical service laboratories in the U.S., Europe, Japan, Latin America and Southeast Asia. Users benefit from 3M’s broad technology base and continuing attention to product development, performance, safety and environmental issues. For additional technical information on Novec 7200DL fluid in the United States or for the name of a local authorized distributor, call 3M Electronics Markets Materials Division: 800 810 8513. Please recycle. Printed in USA. Issued: 9/09 © 3M 2009. All rights reserved. 7004HB 98-0212-2559-8 3M™ Novec™ 7200DL Engineered Fluid 3M and Novec are trademarks of 3M Company. Used under license by 3M subsidiaries and affiliates. Product Use: All statements, technical information and recommendations contained in this document are based on tests or experience that 3M believes are reliable. However, many factors beyond 3M’s control can affect the use and performance of a 3M product in a particular application, including conditions under which the product is used and the time and environmental conditions in which the product is expected to perform. Since these factors are uniquely within the user’s knowledge and control, it is essential that the user evaluate the 3M product to determine whether it is fit for a particular purpose and suitable for the user’s method of application. Warranty and Limited Remedy: Unless stated otherwise in 3M’s product literature, packaging inserts or product packaging for individual products, 3M warrants that each 3M product meets the applicable specifications at the time 3M ships the product. Individual products may have additional or different warranties as stated on product literature, package inserts or product packages. 3M MAKES NO OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO, ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OR ANY IMPLIED WARRANTY ARISING OUT OF A COURSE OF DEALING, CUSTOM OR USAGE OF TRADE. User is responsible for determining whether the 3M product is fit for a particular purpose and suitable for user’s application. If the 3M product is defective within the warranty period, your exclusive remedy and 3M’s and seller’s sole obligation will be, at 3M’s option, to replace the product or refund the purchase price. Limitation Of Liability: Except where prohibited b.incidental, or consequential regardless of the legal theory asserted, including warranty, contract, negligence or strict liability. The Novec brand is the hallmark for a variety of patented 3M products. Although each has its own unique formula and performance properties, all Novec products are designed in common to address the need for safe, effective, sustainable solutions in industry-specific applications. These include precision and electronics cleaning, heat transfer, fire protection, lubricant deposition and several specialty chemical applications. The 3M™ Novec™ Brand Family 3M™ Novec™ Engineered Fluids 3M™ Novec™ Aerosol Cleaners 3M™ Novec™ 1230 Fire Protection Fluid 3M™ Novec™ Electronic Coatings 3M™ Novec™ Electronic Surfactants United States 3M Electronics Markets Materials Division 800 810 8513 China 3M China Ltd. 86 21 6275 3535 Europe 3M Belgium N.V. 32 3 250 7521 Japan Sumitomo 3M Limited 813 3709 8250 Korea 3M Korea Limited 82 2 3771 4114 Singapore 3M Singapore Pte. Ltd. 65 64508888 Taiwan 3M Taiwan Limited 886 2 2704 9011 Electronics Markets Materials Division 3M Center, Building 224-3N-11 St. Paul, MN 55144-1000 www.3M.com/novec 1-800-810-8513