71033

71033 GAMEWELL-FCI | Alldatasheet

Document overview

• Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
• PDF pages: 3

Technical content

Features

• Full range of detectors including: - Ionization. - Photoelectric. - Combination photo/heat. - Rate-of-rise/fixed temperature.  Full range of bases, including: - Standard 4.0” (10.16 cm), 6.0” (15.24 cm), or 6.0” (15.24 cm) low-profile. - 6.0” (15.24 cm) base with flashing red or green LED. - 6.0” (15.24 cm) base with sounder. - 6.0: (15.24 cm) base with relay and flashing green LED. IONIZATION Series 60 SIGNALING S1195 An ISO 9001-2000 Company THERMAL PHOTOELECTRIC

12 Clintonville Road, Northford, CT 06472 - Tel: (203) 484-7161 - Fax: (203) 484-7118

www.gamewell-fci.com CS-2484 Rev. B page 2 of 3 Operation (Continued) The Gamwell Series 60 thermal detector operates as a combination rate or rise/ fixed temperature detector [71.1°C], 71035-210 @ 210°F [98.8°C]). It contains a pair of matched temperature coefficient thermistors within a white polycarbonate housing. One thermistor is exposed, is in good thermal contact with the sur- rounding air, and responds quickly to changes in air temperature. The other thermistor is insulated from the surrounding air and responds more slowly. The detector responds as a rate-of-rise detector when a temperature difference develops rapidly, causing the ratio of the resistances of the thermistors to exceed the factory preset level. The detector responds as a fixed temperature detector when the sum of the resistances of the insulated thermistor and fixed resistor compared to the resistance of the exposed thermistor reaches a preset level. The Gamewell 71041 combination photo/heat detec- tor incorporates the principles of the 71033 photo- electric smoke detector with the fixed temperature characteristics found in the 71035 thermal detector. The Series 60 conventional detector bases will accept any Series 60 detector heads. The bases have a wide interior diameter for ease of access to wire and terminals. The design of the base is such that the detector will fit in one way only and that a simple clockwise motion is required to plug in a detector. The 71036 base (4.0" [10.16 cm) will mount directly to a 3.5" (8.89 cm) octagonal box (Raco 110 or equal) or a 4.0" (10.16 cm) octagonal box (Raco 125 or equal) with a round cover/plaster ring (Raco 727 or equal). The other Series 60 bases (6.0" [15.24cm]) will mount directly to a 3.5" (8.89 cm) octagonal box (Raco 110 or equal); to a 4.0" (10.16 cm) octagonal box (Raco 125 or equal); or to a 4.0" (10.16 cm) square backbox (Raco 190 or equal). Engineering Specifications General Specification: The contractor shall furnish and install where indi- cated on the plans, (insert TYPE/MODEL NUMBER below). The combination detector head and twist lock base shall be UL Listed as compatible with the alarm panel. The base shall permit interchange with Gamewell’s other Series 60 detectors to facilitate modifications to the installation. The detector shall contain an integral LED that latches when the unit goes into alarm. RF transient techniques shall be employed to minimize false alarms. TYPE/MODEL NUMBER: The contractor shall furnish and install where indi- cated on plans, bases which are compatible with all available Series 60 detectors. Standard 4.0" (10.16 cm), 6.0"(15.24 cm), and 6.0"(15.24 cm) low-profile bases (Gamewell 71036, 71086, and 71086-LOW, respectively) shall use stan- dard screw/crimp style terminals and shall provide terminals for remote LEDs. Where indicated on the plans, the contractor shall furnish bases with a power-indicating flashing LED in the base (Gamewell 71086-RED or 71086-GREEN) which shall use standard screw/crimp style terminals and shall provide terminals for remote LEDs. When required, the contractor shall furnish Gamewell 71393 bases with a power indicating flashing green LED in the base plus a relay with two sets of voltage- free change over contacts (Form-C), may be used as a two-or four-wire base, shall use standard screw/ crimp style terminals and shall provide terminals for remote LEDs. Where indicated on the plans, the contractor shall furnish bases Gamewell 71086-SNDR with a sepa- rately powered (24 volt) internal sounder rated at 85 dB @ 10 feet (3.048 m). The bases shall use stan- dard screw/crimp style terminals and shall provide terminals for remote LEDs. Ionization (Dual chamber) smoke detectors Gamewell 71034. Photoelectric Smoke detectors Gamewell 71033 Photoelectric smoke detectors Gamewell 71033 using a horizontal optical bench housing the infrared emitter and sensor arranged radially to detect forward scattering light. Combination photoelectric/ heat Detector Gamewell 71443 using a horizontal optical bench along with fixed temperature (135°F [57.2°C]) capabilities. Fixed temperature/ rate-of-rise Electronic thermal detector Gamewell 71035 (135°F [57.2°C]) or 71035-160 (160°F [71.1°C]) or

www.gamewell-fci.com CS-2484 Rev. B page 3 of 3 Specifications: Standby Current: Photoelectric, combination photo/heat, or ionization: 30 to 45 µA @ 24 volts. Alarm Voltage: 6 to 28 volts. Normal Alarm Output: 52 mA @ 24 volts. Remote Alarm Output: 20 mA maximum, diode gated. Temperature Range: Photo/Comb/Ion/ Thermal 32 °F to 140°F (0°C to 60°C) Thermal: -5° F to 195° F Humidity: 0% to 95% relative humidity (no condensation) Recommended Spacing: Per NFPA codes. Alarm Current: 6.0 (15.24 cm) detector base with relay: 72 mA @ 24 volts. Ordering Information:

71033 Conventional photoelectric smoke

detector head.

71034 Conventional ionization smoke detec-

tor head.

71443 Conventional combination photo/heat

smoke detector head.

71035 Conventional thermal heat detector

head (135°F [57.2°C]). 71035-160 Conventional thermal heat detector head (160°F [71.1°C]). 71035-210 Conventional thermal heat detector head (210°F [98.8°C]). 71036 Conventional 4.0" (10.16 cm) detector base. 71086 Conventional 6.0" (15.24 cm) detector base. 71086-RED Conventional 6.0" (15.24 cm) detector base with flashing power-indicating red LED. 71086-GREEN Conventional 6.0" (125.24 cm) detector base with flashing power-indicating green LED. 71086-SNDR Conventional 6.0" (15.24 cm) detector base with sounder. 71393 Conventional 4.0" (10.16 cm) detector base with relay and flashing power-indicating green LED. 71086-LOW Conventional 6.0" (15.24 cm) low-pro- file detector base.