7000

DATASHEET SEARCH SITE | WWW.ALLDATASHEET.COM

Document overview

• Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
• PDF pages: 7

Technical content

12 –8 AG ASTAT 7 0 0 0 Series, Industrial E lectropneum atic Tim ing Relay Specialty Relays Catalog 5-17 7 3 450-5 Dim ensions are show n for Dim ensions are in m illim eters USA : +1 800 522 6 7 52 For additional support num bers Revised 3 -13 reference purposes only. unless otherw ise specified. A sia Pacific: +86 0 400 820 6 015 please visit w w w .te.com Specifications subject UK: +44 800 26 7 6 6 6 w w w .te.com to change. D esign & C onstruction There are three m ain com ponents of Series 7000 Tim ing R elays: Tim ing Head cir cu lates air through a vari able length to provide linearly adjustable tim ing. P at ent ed design pro - vides easy ad just ment and long service life under severe operating con di tions. P recision-W ound P otted C oil Total sealing w ithout external leads elim inates m oisture prob lem s, gives m axim um insulation value. Snap-Action Sw itch Assem bly — custom -de signed over-center m echa - nism provides snap action. Standard sw itches are DP DT arrangem ent. Each of these subassem blies form s self-con tained m od ules assem bled at the factory w ith the other tw o to afford a w ide choice of operating types, coil voltages, and tim ing ranges. The squared design with front term inals and rear m ounting perm its the grouping of Series 7000 units side-by-side in m ini - m um panel space. A uxiliary switch es m ay be add ed in the base of the unit, without affecting the overall width or depth. Operation Tw o basic operating types are available. “O n-De lay” m od els provide a delay period on energization, at the end of w hich the sw itch transfers the load from one set of contacts to an oth er. De-energizing the unit dur ing the delay period im me di ate ly recycles the unit, ready ing it for another full de lay period on re-energization. In "O ff-Delay" m odels the sw itch trans - fers the load im me di ate ly upon energiza - tion and the delay period does not be gin until the unit is de-energized. A t the end of the delay period the sw itch returns to its original po si tion. R e- en er giz ing the unit during the delay period im me di ate ly resets the tim ing, ready ing it for another full delay period on de-energization. N o pow er is required during the tim ing period, providing a true off delay. In addition to these basic operating types, “Double-H ead” m odels offer sequential delays on pull-in and drop-out in one unit. W ith the addition of auxiliary sw itches the basic m odels provide tw o- step tim ing. Note: Seism ic & radiation tested E 7 0 0 0 m odels are available. C onsult factory for detailed in for ma tion. On-delay m odel 7 0 1 2 (delay on pickup) A pplying voltage to the coil (L1-L2) for at least 5 0 m sec starts a tim e delay lasting for the preset tim e. D uring this pe ri od the nor mal ly closed con tacts (3-5 and 4 -6) re main closed. A t the end of the delay period the nor mal ly closed contacts break and the norm ally open contacts (1-5 and 2-6) m ake. T he con tacts re main in this trans ferred po si tion until the coil is deenergized, at w hich tim e the sw itch re turns to its orig i nal position. De-energizing the coil, either dur ing or after the de lay pe ri od, w ill re cy cle the unit w ithin 5 0 m sec. It w ill then pro vide a full delay period upon re-energization, re gard less of how often the coil voltage is in ter rupt ed before the unit has been per mit ted to "tim e-out" to its full delay setting. Off-delay m odel 7 0 22 (delay on dropout) A pplying voltage to the coil (for at least 5 0 m sec) w ill transfer the sw itch, breaking the nor mal ly closed contacts (1-5 and 2-6), and m ak ing the nor mal ly open contacts (3-5 and 4 -6). C ontacts rem ain in this transferred position as long as the coil is en er gized. T he tim e delay be gins im m ediately upon de-energization. A t the end of the de lay period the sw itch returns to its norm al po si tion. R e-energizing the coil during the delay period w ill im me di ate ly return the tim ing m echanism to a point w here it w ill pro - vide a full delay period upon sub se quent de-energization. T he sw itch rem ains in the transferred position. P roduct Facts n Available in on-delay, true off-delay, and on/off-delay n Tim ing from 0 .1 seconds to 60 m inutes, in linear increm ents n Oversize adjustm ent knobs, serrated w ith high-resolution m arkings visible from all angles m akes the tim er easy to set tim ers n Inherent transient im m unity n Standard voltages from 6-550 VAC and 1 2-550 VD C (special voltages available) n Available in 2-pole or 4-pole m odels n Num erous enclosure options — explosion proof, dust tight, w atertight, herm etically-sealed, NE M A 1 n Auxiliary tim ed and instantaneous sw itches can be added for greater sw itching flexibility n M any m ounting options — Surface m ount, P anel m ount, Octal plug-in m ounting n Options: quick-connect term inals, dial stops, and transient pro tec tion m odule n E asy-to-reach screw term inals, all on the face of the unit, clearly identified n M odular assem bly — tim ing head, coil as sem bly and sw itchblock are all individual m odules, w ith sw itches field-replaceable n File E 1 5631 , File LR291 86 R R Note: 7032 types and certain m odels w ith accessories are not agency approved. Users should thoroughly review the technical data before selecting a product part num ber. It is recom m ended that users also seek out the pertinent approvals files of the agencies/laboratories and review them to ensure the product m eets the requirem ents for a given application. Consult factory for ordering inform ation.

12 –9 AG ASTAT 7 0 0 0 Series, Industrial E lectropneum atic Tim ing Relay (Continued) Specialty Relays Specialty Relays Catalog 5-17 7 3 450-5 Dim ensions are show n for Dim ensions are in m illim eters USA : +1 800 522 6 7 52 For additional support num bers Revised 3 -13 reference purposes only. unless otherw ise specified. A sia Pacific: +86 0 400 820 6 015 please visit w w w .te.com Specifications subject UK: +44 800 26 7 6 6 6 w w w .te.com to change. Auxiliary Sw itch Options To increase the versatility of the basic tim er m od els, aux il ia ry sw itches m ay be added to either on-delay or off-delay types. T hey sw itch additional circuits, pro vide tw o-step tim ing action, or fur - nish electrical in ter lock for sus tained coil energization from a m om entary im pulse, depending on the type selected and its ad just ment. T hey are installed at the factory. A ll aux il ia ry sw itches are SP DT w ith UL listings of 10A @ 125 , 25 0, or 4 80 VA C. A m axim um of one Code T or tw o Code L auxiliary sw itch es m ay be added to each relay. The L or LL sw itch is available w ith on-delay relays only. T he T sw itch is available w ith both the on-delay and off-de lay relays. Auxiliary Sw itch Options for On-D elay Instant Transfer (Auxiliary Sw itch C ode L, m ax i mum of 2 per relay.) 1. Energizing coil begins tim e delay and transfers aux il ia ry sw itch. 2. M ain sw itch transfers after total preset delay. 3. De-energizing coil resets both sw itches instantly. A uxiliary sw itch is nonadjustable. Tw o-Step Tim ing (Auxiliary Sw itch C ode T, m ax i mum of 1 per relay.) 1. Energizing coil begins tim e delay. 2. A fter first delay auxiliary sw itch transfers. 3. M ain sw itch transfers after total preset delay. 4 . De-energizing coil resets both sw itches instantly. First delay is independently adjustable, up to 30% of over all delay. (R ec om mend ed m axim um 100 sec onds.) Auxiliary Sw itch Options for Off-D elay In these m odels the sam e auxiliary sw itch provides ei ther tw o-step tim ing or instant transfer action, de pend ing on the ad just ment of the actuator. Tw o-Step Tim ing (Auxiliary Sw itch C ode T, m ax i mum of 1 per relay.) 1. Energizing coil transfers m ain and auxiliary sw itch es in stant ly. 2. De-energizing coil begins tim e delay. 3. A fter first delay auxiliary sw itch transfers. 4 . M ain sw itch transfers after total preset delay. First delay is independ - ently adjustable, up to 30% of over all delay. (R ec om mend ed m axim um 100 sec onds.) Instant Transfer (Auxiliary Sw itch C ode L, m ax i mum of 1 per relay.) 1. Energizing coil transfers m ain and auxiliary sw itch es in stant ly. 2. De-energizing coil resets auxiliary sw itch and be gins tim e delay. 3. M ain sw itch transfers after total preset delay. A uxiliary sw itch is factory adjusted to give instant trans fer op er a tion. Tw o-step tim ing m ay be set at the factory to cus - tom er specification up to a 3:2 ratio. T he Double H ead m odel provides delayed sw itch trans fer on energization of its coil, and de layed resetting upon coil de- energization. Each delay period is in de pen dent ly adjustable. In new circuit designs or the im provem ent of ex ist ing con trols now using tw o or m ore conventional tim ers, the Double H ead unit offers distinct advantages. Its com pact design saves panel space, w hile the sim plified w iring reduces costly in ter con nec tion. On-delay, Off-delay M odel 7 0 32 (D ouble Head) W ith the addition of an extra sw itch block at the bot tom of the basic unit, this version of the Series 7000 offers four pole sw itch capacity w ith sim ul taneous tim ing or tw o-step tim ing. T he tw o-step operation is achieved by factory adjustm ent to your specifications. For tw o-step operation, a m axim um tim ing ratio be tw een upper and low er sw itches of 3:2 is rec om mend ed. O nce ad - just ed at the factory, this ratio rem ains con stant regardless of changes in dial settings. (Ex: If up per sw itch transfer is set on dial at 60 sec., m inim um tim e on low er sw itch should be 4 0 sec.) T his Series 7000 unit offers m any of the per for m ance fea - tures found in basic m odels — voltage ranges, tim ing and sw itch capacities. Four pole m odels add approxim ately 1-1/4 " to the m ax i - mum height of the basic m odel, approxim ately 1/8" to the depth. T hey are designed for vertical op er a tion only. On-delay M odel 7 0 1 4, Off-delay M odel 7 0 24

12 –10 AG ASTAT 7 0 0 0 Series, Industrial E lectropneum atic Tim ing Relay (Continued) Specialty Relays Catalog 5-17 7 3 450-5 Dim ensions are show n for Dim ensions are in m illim eters USA : +1 800 522 6 7 52 For additional support num bers Revised 3 -13 reference purposes only. unless otherw ise specified. A sia Pacific: +86 0 400 820 6 015 please visit w w w .te.com Specifications subject UK: +44 800 26 7 6 6 6 w w w .te.com to change. T he Surge/Transient P rotection O ption pro tects elec tron ic con trol cir cuits from tran sients and surg es w hich are gen er at ed w hen the tim er coil is ac ti vat ed. T he de vice is not po lar i ty sen si tive and perm its the user to ini tiate, delay, sequence and pro gram equip ment ac tions over a w ide range of ap pli ca tions under the m ost se vere operating con di tions. T he varistor w ill not affect the operating characteristics of the 7000 Tim er. T he varistor has bilateral and sym m etrical voltage and current characteristics. P roduct Facts n P rotect electronic control circuits from voltage transients generated by the tim er coil n Fast response to the rapidly rising back E .M .F. n High perform ance clam ping voltage char ac ter is tics n UL recognized, (except varistor and coil together). n Tim er NOT polarity sensitive Surge/Transient P rotection Option Transient Suppressor O ption "V" Tim ing Specifications (A ll values show n are at nom inal voltage and 25 °C unless otherw ise specified) Operating M odes — M odel 7012/7014 — O n-delay (delay on pick-up). M odel 7022/7024 — O ff-delay (delay on drop-out). M odel 7032 — O n-delay, off-delay (double head). Tim ing Adjustm ent — Tim ing is set by sim ply turning the dial to the desired tim e value. In the zone of approxim ately 25 ° sep a rat ing the high and low end of tim ing ranges A ,D,E, and K , in stan ta neous operation (no tim e delay) w ill occur. A ll other ranges produce an infinite tim e de lay w hen the dial is set in this zone. M odels 7014 and 7032 are available w ith letter dials only. The upper end of the tim e ranges in these m odels m ay be tw ice the values show n. Linear Tim ing Ranges — M odels 7012, M odels 7014, C ode 7022, 7024 703 2 A .1 to 1 Sec. .2 to 2 Sec. B .5 to 5 Sec. .7 to 7 Sec. C 1.5 to 15 Sec 2 to 2 0 Sec. D 5 to 50 Sec. 10 to 100 Sec. E 2 0 to 2 00 Sec. 3 0 to 3 00 Sec. F 1 to 10 M in. 1.5 to 15 M in. H 3 to 3 0 M in. 3 to 3 0 M in. I 6 to 60 M in. N ot Avail. J 3 to 12 0 C yc. N ot Avail. K 1 to 3 00 Sec. N ot Avail. Repeat Accuracy — For delays of 2 00 seconds or less: 7012 *, 702 2 , 702 4: ±5% 7014*: ±10% 703 2 : ±15% For delays greater than 2 00 seconds: 7012 *, 702 2 , 7014*, 702 4: ±10% 703 2 : ±15% * T he first tim e delay afforded by M odel 7012 w ith H (3 to 30 m in.) and I (6 to 60 m in.) tim e ranges or M odel 7014 w ith H tim e range w ill be approx. 15 % long er than sub se quent delays due to coil tem perature rise. Reset Tim e — 5 0 m sec. (except m odel 7032) Relay Release Tim e — 5 0 m sec. for on-delay m odels (7012/7014 ) Relay Operate Tim e — 5 0 m sec. for off-delay m odels (7022/7024 ) Operating Voltage C oil D ata (for D P D T) O perating* O perating C oil C ode R ated Voltage R ated Voltage Part # Letter Voltage R ange Volt age R ange @ 6 0H z @ 50H z 7000 A 12 0 102 -13 2 110 9 3 .5-12 1 B 2 40 2 04-2 64 2 2 0 187-2 42 C 480 408-52 8 D 550 468-605 E 2 4 2 0.5-2 6.5 AC F 12 7 108-140 G 2 40 2 04-2 64 H 12 10.2 -13 .2 I6 5.1-6.6 J 2 08 178-2 2 9 K D ual Voltage C oil (C om bines A&B) L Special AC C oils (L1, L2 , etc.) 7010 M 2 8 2 2 .4-3 0.8 N 48 3 8.4-52 .8 O 2 4 19 .2 -2 6.4 P 12 5 100-13 7.5 Q 12 9 .6-13 .2 R 60 48-66 D C S 2 50 2 00-2 75 T 550 440-605 U 16 12 .8-17.6 V 3 2 2 5.8-3 5.2 W 9 6 76.8-105.6 Y6 4.8-6.6 Z 2 2 0 176-2 42 X Special D C C oils (X1, X2 , etc.) *Four pole M odels: O perational voltage range 90% to 110% for A C units; 85 % to 110% for DC units. See next page for m ore coil data.

12 –11 AG ASTAT 7 0 0 0 Series, Industrial E lectropneum atic Tim ing Relay (Continued) Specialty Relays Specialty Relays Catalog 5-17 7 3 450-5 Dim ensions are show n for Dim ensions are in m illim eters USA : +1 800 522 6 7 52 For additional support num bers Revised 3 -13 reference purposes only. unless otherw ise specified. A sia Pacific: +86 0 400 820 6 015 please visit w w w .te.com Specifications subject UK: +44 800 26 7 6 6 6 w w w .te.com to change. Tim ing Specifications (A ll values show n are at nom inal voltage and 25 °C unless otherw ise specified) M inim um operating voltages are based on ver ti cal ly m ount ed 7012 units. 7012 hor i - zon tal ly m ounted or 7022 ver ti cal ly or horizontally m ounted units w ill operate sat is - fac to ri ly at m inim um voltages approxim ately 5 % low er than those list ed. A C units drop out at approxim ately 5 0% of rated voltage. DC units drop out at ap prox - i mate ly 10% of rated voltage. A ll units m ay be operated on interm ittent duty cy cles at voltages 10% above the listed m axim um s (in ter mit tent duty - m axim um 5 0% duty cycle and 30 m inutes “on” tim e.) Surge/Transient P rotection Option C haracteristics (D C Tim ers Only) C oil Voltage M ax E xcess M ax D e-energization N om inal (D C ) E nergy C apacity (Joule) Tran sient Voltage 12 V 0.4 J 48 V 2 4 V 1.8 J 9 3 V 2 8 V 1.8 J 9 3 V 3 2 V 2 .5 J 13 5 V 48 V 3 .57 J 145 V

60 V 6 J 2 50 V

110 V 10 J 3 40 V

Surge Life — A pplied 100,000 tim es continuously w ith the in ter val of 10 seconds at room tem pera - ture. Below 68 VA C: 12A ; A bove 68 VA C: 35 A Tem perature Range — O perating — -22°F to +167°F (-30°C to + 75 °C) Storage — -4 0°F to +167°F (-4 0°C to +75 °C) Output/Life C ontact Ratings — Contact Capacity in A m ps (R esistive Load) C ontact M in. 100,000 M in. 1,000,000 Voltage O perations O perations 3 0 VD C 15.0 7.0 110 VD C 1.0 0.5 12 0 V 60H z 2 0.0 15.0 2 40 V 60H z 2 0.0 15.0 480 V 60H z 12 .0 10.0

10 A m ps R esistive, 24 0 VA C

1/4 H orsepow er, 120 VA C/24 0VA C (per pole)

15 A m ps 30 VDC (per pole)

5 A m ps, G eneral P urpose, 600VA C (per pole)

D ielectric — W ithstands 15 00 volts R M S 60H z betw een term inals and ground. 1,000 volts R M S 60 H z betw een non-con nect ed term inals. For dielectric specification on herm etically sealed m od els consult factory. Insulation Resistance — 5 00 M egohm s w ith 5 00VDC applied. Tem perature Range — O perating — -20°F to +165 °F (-29°C to 74 °C) Storage — -67°F to +165 °F (-5 5 °C to 74 °C) Tem perature Variation — Using a fixed tim e delay w hich w as set and m easured w hen the am bient tem perature w as 77°F (25 °C), the m axim um observed shift in the average of three con sec u tive tim e de lays w as -20% at -20°F (-29°C) and +20% at 165 °F (74 °C). M ounting/Term inals — N orm al m ounting of the basic unit is in a vertical po si tion, from the back of the panel. All units are tested for vertical operation. Basic m odels (7012, 7022) m ay also be horizontally m ount ed, and w ill be adjusted ac cord - ing ly w hen Accessory Y1 is spec i fied in your order. Standard screw term inals (8-32 truss head screw s sup plied) are located on the front of the unit, w ith per ma nent sche mat ic m arkings. Barrier isolation is de signed to ac com - mo date spade or ring tongue ter mi nals, w ith spacing to m eet all industrial control spec i fi ca tions. T he basic Series 7000 m ay also be panel m ounted w ith the addition of a panel m ount kit, X option, that includes all nec es sary hardw are and faceplate. T his offers the con ve nience of “out-front” adjustm ent, w ith large dial skirt knob. T he faceplate and knob blend w ith ad vanced equipm ent and console designs, w hile the body of the unit and its w iring are protected behind the panel. O ther m ounting options include plug-in styles and special configurations to m eet unusual installation re quire ments. Contact factory for details. P ow er C onsum ption — A pproxim ately 8 w atts pow er at rated voltage . Approxim ate W eights — W eight m ay vary slightly w ith coil voltage.

12 –12 AG ASTAT 7 0 0 0 Series, Industrial E lectropneum atic Tim ing Relay (Continued) Specialty Relays Catalog 5-17 7 3 450-5 Dim ensions are show n for Dim ensions are in m illim eters USA : +1 800 522 6 7 52 For additional support num bers Revised 3 -13 reference purposes only. unless otherw ise specified. A sia Pacific: +86 0 400 820 6 015 please visit w w w .te.com Specifications subject UK: +44 800 26 7 6 6 6 w w w .te.com to change. Outline D im ensions (D im ensions in inches) P anel M ount Option “X” Surge/Transient P rotection Option M odels 7 0 1 4, 7 0 24 M odel 7 0 32 M odels 7 0 1 2, 7 0 22

12 –13 AG ASTAT 7 0 0 0 Series, Industrial E lectropneum atic Tim ing Relay (Continued) Specialty Relays Specialty Relays Catalog 5-17 7 3 450-5 Dim ensions are show n for Dim ensions are in m illim eters USA : +1 800 522 6 7 52 For additional support num bers Revised 3 -13 reference purposes only. unless otherw ise specified. A sia Pacific: +86 0 400 820 6 015 please visit w w w .te.com Specifications subject UK: +44 800 26 7 6 6 6 w w w .te.com to change. Our authorized distributors are m ore likely to m aintain the follow ing item s in stock for im m ediate delivery. 70 12AA 70 12AB 70 12AC 70 12AD 70 12AE 70 12AF 70 12AH 70 12AK 70 12AC L 70 12B C 70 12N C 70 12PA 70 12PB 70 12PC 70 12PD 70 12PF 70 12PJ 70 12PK 70 12PKX 70 12PJX 70 22AA 70 22AB 70 22AC 70 22AD 70 22AE 70 22AF 70 22AH 70 22AI 70 22AJ 70 22AKT 70 22B C 70 22B K 70 22PA 70 22PB 70 22PC 70 22PK Typical P art No. ‰ 70 12 A D G Z 1. Basic Series: 70 = 7000 series electropneum atic tim ing relay 2. O peration: 1 = O n-delay 3 = O n-delay, off-delay (double head) 2 = O ff-delay 3 . C ontact A rrangem ent: 2 = 2 PD T (2 form C ) **4 = 4PD T (4 form C ) 4. C oil Voltage: AC C oils D C C oils A = 12 0VAC, 60 H z.; 110VAC, 50H z. M = 2 8VD C B = 2 40VAC, 60 H z.; 2 2 0VAC, 50H z. N = 48VD C C = 480VAC, 60 H z. O = 2 4VD C D = 550VAC, 60 H z. P = 12 5VD C E = 2 4VAC, 60 H z. Q = 12 VD C F = 12 7VAC, 50 H z. R = 60VD C G = 2 40VAC, 50H z. S = 2 50VD C H = 12 VAC, 60 H z. T = 550VD C K = D ual voltage (com bines A & B) U = 16VD C L = Special AC coils (L1, L2 , etc.) V = 3 2 VD C W = 9 6VD C Y = 6VD C Z = 2 2 0VD C X = Special D C coils (X1, X2 , etc.) 5. Tim ing R ange: M odels 7012 , 702 2 & 702 4 †M odels 7014 & 703 2 A = .1 to 1 sec. For m odel 703 2 specify separate tim e B = .5 to 5 sec. range code for each head. E xam ple: AB. C = 1.5 to 15 sec. Any tw o ranges m ay be selected. D = 5 to 50 sec. A = .2 to 2 sec. E = 2 0 to 2 00 sec. B = .7 to 7 sec. F = 1 to 10 m in. C = 2 to 2 0 sec. H = 3 to 3 0 m in. D = 10 to 100 sec. I = 6 to 60 m in. E = 3 0 to 3 00 sec. J = 3 to 12 0 cyc. F = 1.5 to 15 m in. K = 1 to 3 00 sec. H = 3 to 3 0 m in. 6 . O ptions: A1 = Single quick-connect term inals (note 4). l2 = T am per-proof C ap, transparent (C annot be com bined w ith O ption X). A2 = D ouble quick-connect term inals (note 4). L = Auxiliary Sw itch, instant transfer. 7012 only (notes 2 & 6). B = Plug-in connectors (note 4). LL = T w o Aux. Sw itches, instant transfer. O n M odel 7014 Factory Installed O nly. (notes 2 & 6) G Z = E nclosure w ith bottom knockouts (note 1). M = D ust-tight G asketing (notes 4 & 5). H 3 = H erm etically sealed enclosure, 8 pin octal (notes 1 & 4). S = D ial Stops. H 4 = H erm etically sealed enclosure, 8 screw term inal block (notes 1 & 4). T = Auxiliary Sw itch, tw o-step tim ing (notes 2 & 6). *H 6 = H erm etically sealed enclosure, 11 pin solder (notes 1 & 4). V = T ransient/Surge Protection (for D C coil voltage only). *H 7 = H erm etically sealed enclosure, 11 pin octal (notes 1 & 4). X = Panelm ount includes hardw are and adjustm ent for horizontal operation (note 4) *H 8 = H erm etically sealed enclosure, 11 screw term inal block (notes 1 & 4). Y1 = H orizontal testing, for horizontal operation w ithout panel m ounting (note 4). l1 = T am per-proof C ap, opaque black (C annot be com bined w ith O ption X). Y2 = H orizontal testing, w ith C om pensating Spring for vertical operation (note 4). N otes: 1. C annot be com bined w ith B, P or X O ptions 2 . C annot be com bined w ith B, P or Y2 O ptions 3 . C annot be com bined w ith G Z, H , l1, l2 , K , W or Y1 O ptions 4. N ot Avail. on 4-Pole M odels 5. N ot Available w ith L, T or LL options. 6. N ot Available on herm etically sealed units. * Sized to accom m odate one L or T Auxiliary Sw itch ** N ot available on 703 2 m odel. † Available w ith letter graduated dials only. U pper end of tim e range m ay be tw ice the value show n †† 12 0 cycles = 2 sec. Ordering Inform ation

12 –14 Specialty Relays Catalog 5-17 7 3 450-5 Dim ensions are show n for Dim ensions are in m illim eters USA : +1 800 522 6 7 52 For additional support num bers Revised 3 -13 reference purposes only. unless otherw ise specified. A sia Pacific: +86 0 400 820 6 015 please visit w w w .te.com Specifications subject UK: +44 800 26 7 6 6 6 w w w .te.com to change. AG ASTAT 7 0 0 0 Series, Industrial E lectropneum atic Tim ing Relay (Continued) Ordering Options — C an only be ordered as factory installed options (D im ensions, w here show n, are in inches) A1 – Single Quick-C onnect Ter mi nals A2 – D ouble Quick-C onnect Ter mi nals G asket G asket O rdering options can only be ordered as factory installed options. Transient Protection P lug-In Receptacle (Accessory C ) P lug-In Receptacle (Accessory D ) Q uick Connect Term inals C atalog No. 7 0 0 1 41 . For use w ith “B” O ption. Screw Term inals C atalog No. 7 0 0 1 37 . For use w ith “B” O ption. Accessories (N ot available for 7032 m odels) B – P lug-In C onnectors Use w ith A ccessory “C” or “D” below. G Z – M etal E n clo sure W ith knockouts for bottom connection. 3.16" W x 3.84 " D x 7.63"H I – Tam per-P roof C over H – Herm etically Sealed E nclosure L – Auxiliary Sw itch M – D ust tight LL – Auxiliary Sw itch S – D ial Stops P – Octal P lug Adapter V – Transient/Surge P rotection T – Auxiliary Sw itch X – P anelm ount K it M ounting hardw are included.