650889-5

650889-5 TE-CONNECTIVITY | Alldatasheet

Document overview

• Manufacturer or author: Provided By alldatasheet.com(free datasheet download site)
• PDF pages: 18

Technical content

Application SpecificationEurocard Connectors Types B, C, M, Q, R, and Enhanced Type C 114- -9014 LOC B 1 of 18E2012 Tyco Electronics Corporation, a TE Connectivity Ltd. Company All Rights Reserved TE logo is a trademark. *Trademark. Other product names, logos, or company names might be trademarks of their respective owners. TOOLING ASSISTANCE CENTER 1- -800- -722- -1111 PRODUCT INFORMATION 1- -800- -522- -6752 This controlled document is subject to change. For latest revision and Regional Customer Service, visit our website atwww.te.com (Board- to- Board Application) 18 JUN 12 Rev K All numerical values are in metric units [with U.S. customary units in brackets]. Dimensions are in millimeters [and inches]. Unless otherwise specified, dimensions have a tolerance of +0.13 [+.005] and angles have a tolerance of +2_. Figures and illustrations are for identification only and are not drawn to scale. 1. INTRODUCTION This specification covers requirements for the printed circuit (pc) board- -to- -board application of Eurocard Connectors Types B, C, M, Q, R, and Enhanced Type C. These two- -piece, 2.54 mm [.100 in.] row- -to- -row and in- -row centerline contact connectors are designed to mate with all DIN 41612 and IEC 603- -2 connectors of similar type and contact arrangement. The two- - and three- -row connectors are available in 32, 64, and 96 positions, as well as half sizes and expanded sizes as mating pin and receptacle connectors. The housings are available pre- -loaded with ACTION PIN* thin stock and square stock contacts (0.64 mm [.025 in.]), solder tines and wrap- -type contacts in various lengths. Type M housings have contact cavities at each end that will accept solder cup, coaxial crimp- -type, and solder type contacts. Multiple pin heights for connectors with make first, break last (MFBL) contacts and selective contact loading are available. When corresponding with TE Connectivity Personnel, use the terminology provided in this specification to facilitate your inquiries for information. Basic terms and features of these components are provided in Figure 1. Figure 1 (cont’d) Row ARow B Row C ACTION PIN Thin Stock Contact Boardlock Solder Tine ACTION PIN 0.64 mm [.025 in.] Square Stock Contact Polarizing Bar Housing Type C Receptacle Connector Type R Receptacle Connector Type R Pin Connector Type C Pin Connector Mounting Ear Wrap- -Type Contact Socket Contacts Pin Contact Pin Hood Polarizing Indent Ribbing Standoff NOTE i

Figure 1 (end) Type M Pin ConnectorType M Receptacle Connector ACTION PIN Thin Stock Contact Solder Tine Coaxial Cable In- -Line Contact PC Board Mount Power Contact Solder Cup Power Contact Coaxial Solder Tine Contact Right- -Angle Cable Contact Coaxial Cable In- -Line Contact Solder Cup Power Contact PC Board Mount Coaxial Contact Right- -Angle PC Board Mount Power Contact 2. REFERENCE MATERIAL 2.1. Revision Summary The following revision summary of changes and additions have been made to this specification for this revision. S Updated document to corporate requirements S Corrected dimension line in Figure 10 2.2. Customer Assistance Product Base Part Number 535032 and Product Code 5607 are representative of Eurocard Connectors. Use of these numbers will identify the product line and expedite your inquiries through a service network established to help you obtain product and tooling information. Such information can be obtained through a local TE Representative or, after purchase, by calling the Tooling Assistance Center number at the bottom of page 1. 2.3. Drawings Customer Drawings for product part numbers are available from the service network. The information contained in Customer Drawings takes priority if there is a conflict with this specification or with any other technical documentation supplied by TE. 2.4. Specifications Product Specification 108- -26003 provides information for ACTION PIN contacts. Product Specification 108- -5299 contains information for ACTION PIN contacts and solder type contacts for Type Q connectors.

2.5. Instructional Material Available instruction sheets (408- -series) and customer manuals (409- -series) contain detailed assembly instructions and repair procedures for product and tooling. Documents available which pertain to Eurocard connectors are: 408- -9027 Adapter Kit for Greenerd Frame Assembly 408- -9623 Seating Tool 535072- -1 (for Type C Receptacle Connectors and Seating Tool 148090- -[ ] for Type M Receptacle Connectors) 408- -9740 Seating Tools 768211- -[ ] (for Type R Connectors with ACTION PIN Contacts) 408- -9894 Programmable Seating Tools 768216- -[ ] (for Type R Connectors with MFBL Contacts) 2.6. Manuals Manual 402- -40 is available upon request and can be used as a guide in soldering. This manual provides information on various flux types and characteristics along with the commercial designation and flux removal procedures. A checklist is included in the manual as a guide for information on soldering problems. 3. REQUIREMENTS 3.1. PC Board A. Thickness 1. Connectors with ACTION PIN contacts are available in two designs: one for pc boards with a minimum thickness of 1.57 mm [.062 in.] and one for pc boards with a minimum thickness 2.36 mm [.093 in.]. 2. Connectors with solder tines or ACTION PIN thin stock contacts require a minimum pc board thickness of 1.57 mm [.062 in.]. B. Layout The suggested pc board layout should be as specified in Figure 2.

Figure 2 (cont’d) Type B Pin Connector and Type Q Receptacle Connector Type Q Pin Connector and Type B Receptacle Connector Type R Pin Connector and Type C Receptacle Connector H S e eF i g u r e3 “A” (Number of Spaces x 2.54 [.100]) Dim. A + (Two x Dim. B) “B” “A” (Number of Spaces x 2.54 [.100]) Dim. A + (Two x Dim. B) “A” (Number of Spaces x 2.54 [.100]) Dim. A + (Two x Dim. B) “B” “B”

Figure 2 (cont’d) H S e eF i g u r e3 Type M Pin Connector Type M Receptacle Connector Type C Pin Connector and Type R Receptacle Connector “A” (Number of Spaces x 2.54 [.100]) Dim. A + (Two x Dim. B) “B” (For Solder Tine Coaxial Connectors) (For Crimp- -Type, Solder Cup Type and Power Contacts) “A” (Number of Spaces x 2.54 [.100]) (For Crimp- -Type, Solder Cup Type and Power Contacts) (For Solder Tine Coaxial Connectors) “A” (Number of Spaces x 2.54 [.100])

Figure 2 (end) Enhanced Type C Receptacle Connector Enhanced Type C Pin Connector H S e eF i g u r e3 Number of Spaces (Between Three- -Row Positions) x Dim. C Number of Spaces (Between Four- -Row Positions) x Dim. A “A” “C” “C” “B” Dim. C + (Two x Dim. B) “B” Three- -Row Position (Ref) Four- -Row Position (Ref) Number of Spaces (Between Three- -Row Positions) x Dim. C Number of Spaces (Between Four- -Row Positions) x Dim. A “A”

C. Hole Dimensions(Figure 3) Values specified in the following must be complied with to ensure proper performance. The drilled hole diameter and the copper plating thickness are of major importance and must be adhered to. Pad Diameter Copper Plating Drilled Hole Diameter FR- -4 Material (Ref) Refer to Paragraph 3.1.A.1 and .2 for PC Board Thickness Surface Finish Thickness HASL Sn Pb 0.008 [.0003] Min. Immersion Sn 0.0005 [.000020] Min. Immersion Au/Ni 0.004- -0.005 Ni, 0.0001- -0.0005 Au Immersion Ag 0.0001 [.000004] Min. Finished Hole Dia. After Plating PC BOARD HOLE CONTACT TYPE DIAMETER PLATING THICKNESS PC BOARD PAD (MIN DIA)TYPE TYPE DRILLED AFTER PLATING (REF) COPPER (KNOOP- -150 Max) SURFACE FINISH P A D( M I ND I A) Plated- -Through 1.125- -1.176 [.0443- -.0463]z 1.02 [.040]B 0.03- -0.08 [.001- -.003] See Surface Finish/Thickness 1.57 [.062] ACTION PIN Plated- -Through (Type Q) 0.874- -0.925 [.0344- -.0364] 0.80 [.031] 0.03- -0.08 [.001- -.003] See Surface Finish/Thickness Callout in Above Illustration 1.57 [.062] Non- - Plated- -Through 1.125- -1.176 Solder Tine Plated- -Through 1.125- -1.176 [.0443- -.0463] 0.99 [.039] 0.03- -0.08 [.001- -.003] See Surface Finish/Thickness Callout in Above Illustration Hole Diameter Plus 0.51 [.020] BFinished hole diameter for immersion Au holes to be 1.04 mm [.041 in.] ref. Figure 3 3.2. Housing Features A. Boardlocks The solder tine connectors are available with boardlocks which help retain the connector onto the pc board. Specialapplication tooling or equipment is not required for connectors with boardlocks. B. Mounting Ears and Standoffs These connectors are designed with mounting ears in different thicknesses and spacing between standoffs. Those with larger mounting ear height and closer standoff spacing do not require a seating tool to push the ACTION PIN contacts through the pc board holes to seat the connector. Those with smaller mounting ear height and greater standoff spacing require the use of a seating tool. See Figure 4.

B. Mating Dimensions Possible mating configurations are illustrated in Figure 10. The dimensions shown are for reference only when designing systems. Designated centerlines indicate mounting hole location. Refer to the applicable TE customer drawing for connector dimensions. Figure 10 (cont’d) Type B Pin and Receptacle Connector Type Q Pin and Receptacle Connector Type C Pin and Receptacle Connector Type M and Enhanced Type C Pin and Receptacle Connector Type Q Pin and Type B Receptacle ConnectorD D When connector types are mixed (forexample, C and R), the connector circuit numbers will not match; for example, Position A1 of the pin connector will mate with PositionA32 of the receptacle connector. NOTE i

Figure 10 (end) Type C Pin and Type R Receptacle ConnectorD D When connector types are mixed (for example, C andR), the connector circuit numbers will not match; for example, Position A1 of the pin connector will matewith Position A32 of the receptacle connector. Type B Pin and Type Q Receptacle ConnectorD Type R Pin and Receptacle Connector Type R Pin and Type C Receptacle Connector

Consideration must be given to toxicity and safety requirements recommended on the Material Safety Data Sheet furnished by the solvent manufacturer. If you have a particular solvent that is not listed, consult an TE Representative before using it on these connectors. C. Drying When drying cleaned components and pc boards, make certain the temperature limitations of - -55_ to 125_C[ - - 7 0_ to 260_F] are not exceeded. D. Soldering Guidelines Refer to Paragraph 2.6 of this specification for instructional material that is available for establishing soldering guidelines. Protect lower shroud (vertical connectors) or lower ground plane (enhanced connector) when soldering right- -angle pin connectors. 3.9. Repair In the event of damaged contacts or connector, the entire connector must be replaced with a new one, with the exception of the coaxial contacts in Type M connectors which are removable (refer to Paragraph 5.6). 4. QUALIFICATIONS Eurocard Connectors meet DIN 41612 and IEC 603- -2 specifications. The connectors are also Certified by CSA International in File LR7189 and Recognized under the Component Program of Underwriters Laboratories Inc. (UL) in File E28476. 5. TOOLING 5.1. Application Tooling For low- -volume manufacturing, an arbor frame type applicator may be used; for high- -volume manufacturing, machine application is recommended. See Figure 13. Figure 13 Typical Arbor Frame Press (Such as Greenerd 3A or 3B Manual Frame Assembly—refer to 408- -9027 for Adapter Kit when using this type press) “H” Frame Power Unit Machine 803880- -6 SM- -3 Machine 814700- -2 Power Units DANGER NOTE i CAUTION

5.2. PC Board Support A pc board support (customer supplied) must be used for the seating of connectors. While many materials can be used for this, steel or cast aluminum is recommended. A. Multi- Layered PC Board Support A flat- -plate type support should be used with multi- -layered pc boards having internal circuitry. For details, see Figure 14. B. Single- Layered PC Board Support An anvil type support may be for use with single- -layered pc boards. See Figure 14. Figure 14 Row- -to- -Row Centerline Spacing No. of Spaces x 2.54 [.100] 38.1 +0.05 [1.50 +.002] 25.4 [1.00] 19.05 +0.25 [.75 +.010] 2.54 [.100] Typ 1.17 [.046] Typ 0.38 [.015] 30_+ 2_ 0.25 [.010] Multi-Layered PC Board Support Single-Layered PC Board Support In- -Row Centerline Spacing M

5.3. Seating Tool Seating tools must be used in manual or power assist units with sufficient ram surface and the capability of applying insertion force per contact. The seating tools align the components for proper seating and are specifically designed for the different types of Eurocard connectors. Seating tools, connector types, and instruction sheets are shown in Figure 15. 5.4. Pushing Plate A pushing plate (customer supplied) must be used to seat vertical receptacles with ACTION PIN thin stock contacts and square stock contacts in connectors that do not require special tooling. The pushing plate must be of minimum length and width equal to full top dimensions of the receptacle. The larger the pushing plate, the less critical the alignment during seating. When seating connector, the pushing plate must move in a straight, vertical line, and its bottom surface must be parallel to the top of the pc board support or template when force is applied. See Figure 15. The force used to seat Eurocard connectors with square stock contacts shall not exceed 177.93 N [40 lbs] per contact. Seating force for connectors with ACTION PIN thin stock contacts shall not exceed 88.96 N [20 lbs] per contact. Figure 15 Seating Tools 768211- -[ ] for Type R Vertical Pin Connectors without MFBL Contacts (408- -9740) Programmable Seating Tools 768216- -[ ] for Type R Vertical Pin Connectors with MFBL Contacts (408- -9894) Seating Tool 535072- -1 for Type C Receptacle Connectors (408- -9623) Seating Tool 148090- -[ ] for Type M Receptacle Connectors (408- -9623) Pushing Plate for Vertical Connectors Not Requiring Special Tooling (Customer Supplied) PC Board PC Board Support (Anvil) Vertical Receptacle Applicator Machine Ram NOTE i

5.5. Connector Replacement Tooling When entire Type C receptacle connectors and Type R pin connectors must be replaced, Eurocard Connector Removal Tool Kit 534611- -1 should be used. Refer to Figure 16 and proceed as follows: DO NOT use this tool in a power assist unit. This procedure should be done with a manually operated unit only. 1. Place support block with slot up on the arbor frame support base. 2. Place housing down on support block with pins extending up through pc board. 3. Slide guide block over wire- -wrap tails. Be sure the “T” stamp on end of guide block is away from pc board. 4. Start push- -out assembly into guide block, using care not to damage pins. 5. Lower the arbor ram onto the center of push- -out assembly and apply force until it is seated on guide block. 6. Raise the arbor ram and remove push- -out assembly and guide block. When the board, the connector, and the support block are removed, the connector will fall away with pins removed from the pc board and housing. 5.6. Contact Extraction Tooling Extraction tooling is available for withdrawal of individual power contacts and coaxial contacts from Type M connectors. The tip of the tool is inserted into the contact cavity from the mating side of the housing. The contact is forced out of the rear of the housing by pushing the tool handle. See Figure 16. Figure 16 Ram Push- -Out Assembly Guide Block PC Board Pins Connector Slot Support Block “T” Stamp Extraction Tool 106242- -1 CAUTION