62201-8743 MOLEX | Alldatasheet
Document overview
- Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
- PDF pages: 3
Technical content
Impact™ Backplane Press-In Tool Doc No: ATS-622018743 Release Date: 11-04-09 UNCONTROLLED COPY Page 1 of 3 Revision: C Revision Date: 01-18-11 Impact™ Backplane Module Installation Press-In Tool Application Tooling Specification Sheet Order No. 62201-8743
FEATURES
/square4 Tool provides uniform distribution of press force a cross entire pin array /square4 May be used as a stand-alone tool or mounted in an optional holder with other Molex press-in tools SCOPE Products : Impact™ Orthogonal Backplane Signal Module Assembly, 76855 and 76856 Series, (3-Pair b y 6 Column Assemblies). See Product List below for spe cific part numbers. Product List The following is a partial list of the product orde r numbers and their specifications this tool is des igned to run. Updates to this list are available on www.molex.com .
76855 Series Numbers
Guide Style Columns Assembly Order Number Open Wall 6 76855-0604 76855-0605 76855-0607 76855-0608 76855-1604 76855-1605 76855-1607 76855-1608 Dual End 6 76855-0624 76855-0625 76855-0627 76855-0628 76855-1624 76855-1625 76855-1627 76855-1628 Left End 6 76855-2604 76855-2605 76855-2607 76855-2608 76855-3604 76855-3605 76855-3607 76855-3608 76855-6604 76855-6605 76855-6607 76855-6608 76855-7604 76855-7605 76855-7607 76855-7608 Right End 6 76855-4604 76855-4605 76855-4607 76855-4608 76855-5604 76855-5605 76855-5607 76855-5608 76855-8604 76855-8605 76855-8607 76855-8608 76855-9604 76855-9605 76855-9607 76855-9608
76856 Series Numbers
Guide Style Columns Assembly Order Number Dual End 6 76856-0001
Impact™ Backplane Press-In Tool Doc No: ATS-622018743 Release Date: 11-04-09 UNCONTROLLED COPY Page 2 of 3 Revision: C Revision Date: 01-18-11 Tool Setup Depending on the number of connectors to be installed and/or the press used, this tool can be used alone or with a group of press-in tools, mounted in a 62201-95XX rail (ordered separately). See Figure 1. Tool Installation The 62201-95XX rail is available in a variety of le ngths to accommodate multiple press-in tools. Rail Part Number Rail Overall Length 62201-9501 24mm (0.94 in) 62201-9502 72mm (2.83 in) 62201-9503 156mm (6.14 in) 62201-9504 216mm (8.50 in) 62201-9509 254mm (10.0 in) 62201-9511 305mm (12.0 in) Reference: This Press-In Tool is 12.0mm (0.47in.) l ong. Printed Circuit Board (PCB) Support The Impact™ connectors require up to 3.6kg (8 lb) o f force per pin to press into the PCB. To prevent excessive PCB flexure and/or damage to the PCB, a support pla te is strongly recommended directly beneath the con nector hole pattern. Due to the custom nature of every application, Mole x does not offer any PCB support plate. The custom er must furnish their own support plate. When creating the PCB support plate, remember to al low clearance for the connector pins as they pass t hrough the PCB thickness. Press Equipment Recommendations Many types of presses can be used to install Impact ™ connectors, but to assure consistent connector in stallation Molex recommends the following press criteria: 1. The capability to detect force variations as low as 4.5kg (10 lb) during the press-in cycle; excessive force measurements should stop the press-in cycle. 2. The rate of pressing can be regulated as low as 0.1 3mm (0.005 in) per second. 3. Press stroke control to within 0.25mm (0.010 in). 4. Total press stroke must be at least 19mm (0.75 in). 5. For statistical purposes, automatic collection of f orce and distance data. WITH 62201-95XX RAIL Figure 1 ALONE