6116 3M | Alldatasheet

Document overview

  • Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
  • PDF pages: 4

Technical content

Technical Data July, 2003 Typical Physical Properties Note: The following technical information and data should be considered representative or typical only and should not be used for specification purposes. Base Polyolefin Color White Specific Gravity 0.92 Viscosity @ 375°F (190°C) cps(1) 1300 Open Time 2 minutes

1 Surface Foam(2)

2 Surface Foam(3)

Handling Strength 15 minutes Features • Bonds wide variety of substrates, including most foams, plastics, particle board, light gauge metals.

  • Controlled application with minimal over-spray.
  • One or two surface application.
  • Immediate initial strength.
  • Long bonding range. Product Description 3M™ Spray-Bond Adhesive 6116 is a heat applied, solvent-free, 100% solids, sprayable thermoplastic adhesive. It is a fast, neat alternative to aerosols, contact adhesives and solvent-based adhesives for bonding most foams and many other lightweight materials. 3M spray-bond adhesive 6116 is lower than normal viscosity and is designed for use on fabrics, as the long open time allows flexibility in production. (1)Brookfield Thermocel Viscometer in Centipoise using a #27 Spindle @ 20 RPM. (2)Bonds were made by spraying adhesives onto 3/4 in. thick, 2-lb. density polyester urethane foam. PVC coupons wiped with isopropyl alcohol and then bonded to foam using 5 seconds of firm pressure. After standing for 24 hours, bonds were pulled apart by hand. The criterion for open time is 100% foam tear. (3)Two pieces of 3/4 in. thick, 2-lb. density polyester urethane foam were sprayed and bonded using 5 seconds of firm pressure. After 24 hours, bonds were pulled apart by hand. The criterion for open time is 100% foam tear.

3M ™ Spray-Bond Adhesive 6116 Directions for Use 1. Surface Preparation: Surfaces must be clean, dry and dust free. Wiping with a solvent such as isopropyl alcohol for plastic substrates and 3M™ Scotch-Grip™ Solvent No. 3 or MEK (methyl ethyl ketone) for metal will aid in removing oil and dirt.* *Note: When using solvents, extinguish all ignition sources, including pilot lights, and follow the manufacturer’s precautions and directions for use. 2. Application: 3M™ Spray-Bond Adhesive is designed for spray application using a 3M™ Spray-Bond Applicator. Read and follow the precautions and directions for use in the user’s manual before operating the applicator. Note: Adhesive may be applied as a bead by setting the spray control valve on the 3M spray-bond applicator to 10. Adhesive can also be applied as a film using the 3M™ Polygun™ Applicator Tips. Contact your local 3M representative for more information. 3. Coverage: Coverage will depend on foam density, surface porosity of substrates and strength of adhesive bond required. In all cases, user evaluation will be required to determine the optimum coverage levels. Suggested Adhesive Coverage – Starting Points: - 2 - 4. Set up time: After bond is made, there is immediate strength and no clamping is necessary. Smooth Surface Textured Surface 2 surface application 1-2 grams per square foot 2-3 grams per square foot 1 surface application 3-5 grams per square foot 5-7 grams per square foot

3M ™ Spray-Bond Adhesive 6116 - 3 - Load (psi) Temperature 2 lb. 160°F (69°C) Heat Resistance, Dead Load Shear Typical Performance Characteristics Note: The following technical information and data should be considered representative or typical only and should not be used for specification purposes. Peel Adhesion: Peel bonds of open weave polyester fabric to various substrates were tested at peel angle of 180° at twelve inches per minute rate at a temperature of 73°F (23°C). The value listed is the average force required to peel the fabric from the substrates in pounds per inch bond width (PIW). As this product is lower in viscosity than other 3M™ Spray-Bond Adhesives, the nozzle size used on our equipment for 3M™ Spray-Bond Adhesive 6116 is 0.8 mm in place of the 1.2 mm that comes standard with our equipment. Substrate Peel (PIW) Steel coupon 20.4 AF Polypropylene panel 16.4 CF ABS Plastic 20.3 AF Fir (wood) 21.4 AF SF = Substrate/Adhesive Failure CF = Cohesive Failure AF = Adhesive/Fabric Failure Peel Adhesion: Peel bonds of Steel coupon stock to various fabrics were tested at peel angle of 180° at twelve inches per minute rate at a temperature of 73°F (23°C). The value listed is the average force required to peel the fabric from the steel in pounds per inch bond width (PIW). Substrate Peel (PIW) Open weave polyester fabric 20.4 SF Very smooth, tight polyster fabric 5.2 SF Open weave, polypropylene fabric 12.1 SF Very tight smooth nylon fabric 4 SF SF = Substrate/Adhesive Failure CF = Cohesive Failure AF = Adhesive/Fabric Failure

3M ™ Spray-Bond Adhesive 6116 - 4 - Best storage temperature is 60-80°F (15-32°C). Do not store above 120°F (49°C).Storage Shelf life at recommended conditions is 24 months from date of shipment.Shelf Life Refer to Product Label and Material Safety Data Sheet for health and safety information before using this product. For additional health and safety information, call 1-800-364-3577 or (651) 737-6501. Precautionary Information Printed in U.S.A. ©3M 2003 78-9236-7095-0 (7/03) Industrial Business Industrial Adhesives and Tapes Division 3M Center, Building 21-1W-10, 900 Bush Avenue St. Paul, MN 55144-1000 Recycled Paper 40% pre-consumer 10% post-consumer Except where prohibited by law, 3M and seller will not be liable for any loss or damage arising from the 3M product, whether direct, indirect, special, incidental or consequential, regardless of the legal theory asserted, including warranty, contract, negligence or strict liability. Limitation of Liability This Industrial Adhesives and Tapes Division product was manufactured under a 3M quality system registered to ISO 9002 standards. ISO 9002 To request additional product information or to arrange for sales assistance, call toll free 1-800-362-3550 or visit www.3M.com/adhesives. Address correspondence to: 3M Industrial Adhesives and Tapes Division, Building 21-1W-10, 900 Bush Avenue, St. Paul, MN 55144-1000. Our fax number is 651-778-4244. In Canada, phone: 1-800-364-3577. In Puerto Rico, phone: 1-787-750-3000. In Mexico, phone: 52-70-04-00. For Additional Information All statements, technical information and recommendations contained in this document are based upon tests or experience that 3M believes are reliable. However, many factors beyond 3M’s control can affect the use and performance of a 3M product in a particular application, including the conditions under which the product is used and the time and environmental conditions in which the product is expected to perform. Since these factors are uniquely within the user’s knowledge and control, it is essential that the user evaluate the 3M product to determine whether it is fit for a particular purpose and suitable for the user’s method of application. Product Use Unless stated otherwise in 3M’s product literature, packaging inserts or product packaging for individual products, 3M warrants that each 3M product meets the applicable specifications at the time 3M ships the product. Individual products may have additional or different warranties as stated on product literature, package inserts or product packages. 3M MAKES NO OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OR ANY IMPLIED WARRANTY ARISING OUT OF A COURSE OF DEALING, CUSTOM OR USAGE OF TRADE. User is responsible for determining whether the 3M product is fit for a particular purpose and suitable for user’s application. If the 3M product is defective within the warranty period, your exclusive remedy and 3M’s and seller’s sole obligation will be, at 3M’s option, to replace the product or refund the purchase price. Warranty and Limited Remedy