MAC6071 MOTOROLA | Alldatasheet

Document overview

  • Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
  • PDF pages: 8

Technical content

1Motorola Thyristor Device Data /C0065/C0100/C0118/C0097/C0110/C0099/C0101 /C0073/C0110/C0102/C0111/C0114/C0109/C0097/C0116/C0105/C0111/C0110 /C0083/C0101/C0110/C0115/C0105/C0116/C0105/C0118/C0101 /C0071/C0097/C0116/C0101 /C0084/C0114/C0105/C0097/C0099/C0115 Silicon Bidirectional Thyristors . . . designed primarily for full-wave ac control applications, such as light dimmers, motor controls, heating controls and power supplies; or wherever full-wave silicon gate controlled solid-state devices are needed. Triac type thyristors switch from a blocking to a conducting state for either polarity of applied anode voltage with positive or negative gate triggering.

  • Sensitive Gate Triggering (A and B versions) Uniquely Compatible for Direct Coupling to TTL, HTL, CMOS and Operational Amplifier Integrated Circuit Logic Functions
  • Gate Triggering 4 Mode — MAC6071A,B, MAC6073A,B, MAC6075A,B
  • Blocking Voltages to 600 Volts
  • All Diffused and Glass Passivated Junctions for Greater Parameter Uniformity and Stability
  • Small, Rugged, Thermopad Construction for Low Thermal Resistance, High Heat Dissipation and Durability MAXIMUM RATINGS (TJ = 25°C unless otherwise noted) Rating Symbol Value Unit Peak Repetitive Off-State Voltage(1) (Gate Open, TJ = 25 to 110°C) MAC6071A,B MAC6073A,B MAC6075A,B VDRM 200 400 600 Volts On-State Current RMS (TC = 85°C) IT(RMS) 4 Amps Peak Surge Current (One Full cycle, 60 Hz, TJ = –40 to +110°C) ITSM 30 Amps Circuit Fusing Considerations (t = 8.3 ms) I2t 3.7 A2s Peak Gate Power PGM 10 Watts Average Gate Power PG(AV) 0.5 Watt Peak Gate Voltage VGM 5 Volts Operating Junction T emperature Range TJ –40 to +110 °C Storage Temperature Range Tstg –40 to +150 °C Mounting T orque (6-32 Screw)(2) — 8 in. lb. 1. VDRM for all types can be applied on a continuous basis. Blocking voltages shall not be tested with a constant current source such that the voltage ratings of the devices are exceeded. 2. Torque rating applies with use of compression washer (B52200F006). Mounting torque in excess of 6 in. lb. does not appreciably lower case-to-sink thermal resistance. Main terminal 2 and heatsink contact pad are common. For soldering purposes (either terminal connection or device mounting), soldering temperatures shall not exceed +200°C , for 10 seconds. Consult factory for lead bending options. This document contains information on a new product. Specifications and information herein are subject to change without notice. Preferred devices are Motorola recommended choices for future use and best overall value. Order this document by MAC6071/D /C0077/C0079/C0084/C0079/C0082/C0079/C0076/C0065 SEMICONDUCTOR TECHNICAL DATA  Motorola, Inc. 1996 /C0077/C0065/C0067/C0054/C0048/C0055/C0049/C0065/C0044/C0066 /C0077/C0065/C0067/C0054/C0048/C0055/C0051/C0065/C0044/C0066 /C0077/C0065/C0067/C0054/C0048/C0055/C0053/C0065/C0044/C0066 CASE 77-08 (TO-225AA) STYLE 5 TRIACs

4 AMPERES RMS

*Motorola preferred devices MT1 GMT2 MT1MT2 G MT2 /C0042 /C0042 /C0042

/C0077/C0065/C0067/C0054/C0048/C0055/C0049/C0065/C0044/C0066 /C0077/C0065/C0067/C0054/C0048/C0055/C0051/C0065/C0044/C0066 /C0077/C0065/C0067/C0054/C0048/C0055/C0053/C0065/C0044/C0066

2 Motorola Thyristor Device Data

Characteristic Symbol Max Unit Thermal Resistance, Junction to Case R θJC 3.5 °C/W Thermal Resistance, Junction to Ambient R θJA 75 °C/W ELECTRICAL CHARACTERISTICS (TC = 25°C unless otherwise noted) Characteristic Symbol Min Typ Max Unit Peak Blocking Current (VD = Rated VDRM , gate open) (TJ = 25°C) (TJ = 110°C) IDRM 2.0 µA mA On-State Voltage (Either Direction) (ITM = 6 A Peak) VTM — 1.3 2.0 Volts Peak Gate Trigger Voltage (Continuous dc) (TJ = –40°C) (Main Terminal Voltage = 12 Vdc, RL = 100 Ohms) (TJ = 110°C) (TJ = 25°C) VGT 0.5 0.5 0.2 0.2 0.4 0.4 0.8 0.8 0.4 0.4 0.7 0.7 1.9 1.9 0.9 0.9 1.4 1.4 Volts Holding Current (Either Direction) (TJ = –40°C) (Main Terminal Voltage = 12 Vdc, Gate Open) (Initiating Current = 150 mA) (TJ = 25°C) IH 0.4 0.2 2.0 1.0 5.0 mA Latching Current (VD = 6 V) MT2(+), G(+) (I G = 8 mA) T J = 25°C MT2(+), G(–) (I G = 8 mA) MT2(–), G(–) (I G = 8 mA) MT2(–), G(+) (I G = 15 mA) IL 2.0 5.0 1.0 2.0 mA Gate Trigger Current (Continuous dc) (VD = 12 Vdc, RL = 100 Ohms) MAC6071A, MAC6073A, MAC6075A MT2(+), G(+) T J = 25°C MT2(+), G(–) MT2(–), G(–) MT2(–), G(+) MT2(+), G(+) T J = –40°C MT2(+), G(–) MT2(–), G(–) MT2(–), G(+) IGT 0.4 0.4 0.4 0.8 0.8 0.8 0.8 1.6 2.0 3.0 3.0 4.5 3.5 4.5 5.0 5.0 5.0 5.0 mA

/C0077/C0065/C0067/C0054/C0048/C0055/C0049/C0065/C0044/C0066 /C0077/C0065/C0067/C0054/C0048/C0055/C0051/C0065/C0044/C0066 /C0077/C0065/C0067/C0054/C0048/C0055/C0053/C0065/C0044/C0066 3Motorola Thyristor Device Data ELECTRICAL CHARACTERISTICS (TC = 25°C unless otherwise noted) Characteristic UnitMaxTypMinSymbol Gate Trigger Current (Continuous dc) (VD = 12 Vdc, RL = 100 Ohms) MAC6071B, MAC6073B, MAC6075B MT2(+), G(+) T J = 25°C MT2(+), G(–) MT2(–), G(–) MT2(–), G(+) MT2(+), G(+) T J = –40°C MT2(+), G(–) MT2(–), G(–) MT2(–), G(+) IGT 0.4 0.4 0.4 0.8 0.8 0.8 0.8 1.6 1.5 2.5 2.5 3.5 3.0 4.0 4.5 7.5 3.0 3.0 3.0 5.0 8.0 8.0 8.0 mA Turn-On Time (Either Direction) (ITM = 14 Adc, IGT = 100 mAdc) tgt — 1.5 — µs DYNAMIC CHARACTERISTICS Characteristic Symbol Min Typ Max Unit Critical Rate of Rise of Off–State Voltage (VD = 200 V, ITM = 1.4 A, Commutating dv/dt = 0.5 V/C0109/sec, Gate Open, TJ = 110°C, f = 250 Hz, Snubber: CS = 0.1 /C0109F, RS = 56 /C0087, see Figure 16) (di/dt)c — 2.2 — A/ms Critical Rate of Rise of Off–State Voltage (VD = Rate VDRM , Exponential Waveform, RGK = OPEN, TJ = 110°C) dv/dt — 7.0 — V//C0109s QUADRANT DEFINITIONS QUADRANT II QUADRANT I QUADRANT III QUADRANT IV MT2(+) MT2(–) G(–) G(+) SAMPLE APPLICATION: TTL-SENSITIVE GATE 4 AMPERE TRIAC TRIGGERS IN MODES II AND III 0 V –VEE VEE = 5.0 V MC7400 510 Ω 2N6071A LOAD4

115 VAC

NOTES: For detail Digital Interfacing and Silicon Bilateral Switch (SBS) trigger application information, see the Motorola’s Thyristor Data Book (DL137/D, Revision 6). 1. Interfacing Digital Circuits to Thyristor Controlled AC Loads, page 1.6–25. 2. Silicon Bilateral Switch (SBS) Applications, page 1.6–41.

4 Motorola Thyristor Device Data

Figure 1. RMS Current Derating Figure 2. Maximum On–State Power Figure 3. On–State Characteristics Figure 4. Transient Thermal Response Figure 5. Typical Holding Current versus Figure 6. Typical Latching Current versus

6 Motorola Thyristor Device Data

Figure 13. Typical Exponential Static dv/dt Figure 14. Typical Exponential Static dv/dt Figure 15. Critical Rate of Rise of Figure 16. Simplified Test Circuit to Measure the Critical Rate of Rise of Commutating Voltage

200 VRMS

NOTE: Component values are for verification of rated (dv/dt)c. See AN1048 for additional information.

/C0077/C0065/C0067/C0054/C0048/C0055/C0049/C0065/C0044/C0066 /C0077/C0065/C0067/C0054/C0048/C0055/C0051/C0065/C0044/C0066 /C0077/C0065/C0067/C0054/C0048/C0055/C0053/C0065/C0044/C0066 7Motorola Thyristor Device Data PACKAGE DIMENSIONS NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: INCH. STYLE 5: PIN 1. MT 1 2. MT 2 3. GATE –B– –A– M K F C Q H V G S D J R U 1 32 2 PL MAM0.25 (0.010) B M MAM0.25 (0.010) B M DIM MIN MAX MIN MAX MILLIMETERSINCHES A 0.425 0.435 10.80 11.04 B 0.295 0.305 7.50 7.74 C 0.095 0.105 2.42 2.66 D 0.020 0.026 0.51 0.66 F 0.115 0.130 2.93 3.30 G 0.094 BSC 2.39 BSC H 0.050 0.095 1.27 2.41 J 0.015 0.025 0.39 0.63 K 0.575 0.655 14.61 16.63 M 5 TYP 5 TYP Q 0.148 0.158 3.76 4.01 R 0.045 0.055 1.15 1.39 S 0.025 0.035 0.64 0.88 U 0.145 0.155 3.69 3.93 /C0095 /C0095 CASE 77–08 (TO–225AA)

/C0077/C0065/C0067/C0054/C0048/C0055/C0049/C0065/C0044/C0066 /C0077/C0065/C0067/C0054/C0048/C0055/C0051/C0065/C0044/C0066 /C0077/C0065/C0067/C0054/C0048/C0055/C0053/C0065/C0044/C0066

8 Motorola Thyristor Device Data

Motorola reserves the right to make changes without further notice to any products herein. Motorola makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does Motorola assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation consequential or incidental damages. “Typical” parameters can and do vary in different applications. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. Motorola does not convey any license under its patent rights nor the rights of others. Motorola products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the Motorola product could create a situation where personal injury or death may occur. Should Buyer purchase or use Motorola products for any such unintended or unauthorized application, Buyer shall indemnify and hold Motorola and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that Motorola was negligent regarding the design or manufacture of the part. Motorola and are registered trademarks of Motorola, Inc. Motorola, Inc. is an Equal Opportunity/Affirmative Action Employer. How to reach us: USA / EUROPE : Motorola Literature Distribution; JAPAN : Nippon Motorola Ltd.; T atsumi–SPD–JLDC, T oshikatsu Otsuki, P .O. Box 20912; Phoenix, Arizona 85036. 1–800–441–2447 6F Seibu–Butsuryu–Center, 3–14–2 T atsumi Koto–Ku, T okyo 135, Japan. 03–3521–8315 INTERNET : http://Design–NET .com 51 Ting Kok Road, T ai Po, N.T ., Hong Kong. 852–26629298 MAC6071/D /C0042/C0077/C0065/C0067/C0054/C0048/C0055/C0049/C0047/C0068/C0042