591D336X_010C2T

591D VISHAY | Alldatasheet

Document overview

• Manufacturer or author: Provided By alldatasheet.com(free datasheet download site)
• PDF pages: 10

Technical content

www.vishay.com 591D Vishay Sprague Document Number 40012 Revision 22-Nov-04 For technical questions, contact tantalum@vishay.com Solid Tantalum Chip Capacitors TANTAMOUNT®, Low Profile, Low ESR, Conformal Coated, Maximum CV PERFORMANCE CHARACTERISTICS Operating Temperature: - 55°C to + 85°C. (To + 125°C with voltage derating.) Capacitance Range: 1µF to 1000µF

FEATURES

• New case size offerings.
• 1.2mm to 2mm height
• Terminations: Lead (Pb)-free (2) standard.
• Very low ESR
• 8mm, 12mm tape and reel packaging available per EIA- 481-1 and reeling per IEC 286-3. 7” [178mm] standard. 13” [330mm] available.
• Footprint compatible with EIA 535BAAC and CECC 30801 molded chips. Note: The anode termination (D less B) will be a minimum of .012" [0.3mm]. CASE CODE L (MAX.) W H A B D (REF.) J (MAX.) DIMENSIONS in inches [millimeters] W D L A B J J Tantalum Wire Nib Identifies Anode (+) Terminal H Capacitance Tolerance: ±10%, ±20% standard. Voltage Rating: 4WVDC to 10WVDC, (16WVDC, 20WVDC, and 25WVDC under development)

ORDERING INFORMATION

T REEL SIZE AND PACKAGING 591D TYPE TERMINATION W CASE CODE 6R3 DC VOLTAGE RATING @ + 85°C CAPACITANCE TOLERANCE 477 CAPACITANCE This is expressed in picofarads. The first two digits are the significant figures. The third is the number of zeros to follow. X0 = ± 20% X9 = ± 10% This is expressed in volts. To complete the three-digit block, zeros precede the voltage rating. A decimal point is indicated by an "R" (6R3 = 6.3 volts). See Ratings and Case Codes Table. 2 = 100% Tin. T = Tape and Reel 7" [178mm] Reel W = 13” [330mm] Reel Note: Preferred Tolerance and reel sizes are in bold. We reserve the right to supply higher voltage ratings and tighter capacitance tolerance capacitors in the same case size. Voltage substitutions will be marked with the higher voltage rating Note: U, V and W are similar to C, D and R footprint (592D) with a 2mm height

www.vishay.com 591D Vishay Sprague Document Number 40012 Revision 22-Nov-04 For technical questions, contact tantalum@vishay.com 1 BA

2.2 BAC B

3.3 CBD C

4.7 AB AC R

6.8 AC BDCR D

10 B A C B D B R D R

15 B A D R C U* R

22 B A A/B C B D C R/V* D/U* V*

33 C B D C R C/D V* R V*

100 R D D/R C U D V

150 C/R U D/R V U W*

220 U D V R/U V/W

330 V U W U/V W

470 W U/V U/V/W

680 V/W W

µF 4 V 6.3 V 10 V 35 V25 V20 V16 V RATINGS AND CASE CODES STANDARD / EXTENDED RATINGS STD EXT STD EXT STD EXT STD EXT STD EXT STD EXT STD EXT CAPACITANCE (µF) CASE CODE PART NUMBER* Max. DCL @ + 25°C (µA) Max. DF @ + 25°C 120 Hz (%) Max. ESR @ + 25°C 100kHz (Ohms) Max. RIPPLE 100kHz Irms (Amps) ** xyH indicates maximum height in (mm), i.e., 1.5mm max. (H) = 15Hmm * Preliminary values contact factory for availability. For 10% tolerance, specify "9"; for 20% tolerance, change to "0”. Extended ratings are in bold print. 22 A 591D226X_004A2T 0.9 6 1.200 0.22 22 B 591D226X_004B2T 0.9 6 0.800 0.32 47 B 591D476X_004B2T 1.9 6 0.800 0.33 47 C 591D476X_004C2T 1.9 6 0.200 0.74 68 C 591D686X_004C2T 2.7 6 0.180 0.78 68 D 591 D686X_004D2T 2.7 6 0.140 1.04 100 D 591D107X_004D2T 4.0 8 0.130 1.07 100 R 591D107X_004R2T 4.0 8 0.110 1.22 150 C 591D157X_004C2T 6.0 8 0.150 0.86 150 R 591D157X_004R2T 6.0 8 0.100 1.28 220 D 591D227X_004D2T 8.8 8 0.100 1.22 220 U 591D227X_004U2T 8.8 8 0.075 1.21 330 V 591D337X_004V2T 13.2 8 0.060 1.53 330 U 591D337X_004U2T 13.2 8 0.070 1.25 470 W 591D477X_004W2T 18.8 8 0.045 1.97 470 U 591D477X_004U2T 18.8 10 0.07 1.25 470 V 591D477X_004V2T 18.8 10 0.060 1.52 680 V 591D687X_004V2T 27.2 12 0.085 1.28 680 W 591D687X_004W2T 27.2 12 0.045 1.97 1000 W 591D108X_004W2T 40.0 14 0.050 1.67 15 A 591D156X_6R3A2T 0.9 6 1.300 0.24 15 B 591D156X_6R3B2T 0.9 6 0.800 0.32 22 A 591D226X_6R3A2T13H 1.4 6 0.800 0.20 22 B 591D226X_6R3B2T 1.4 6 0.800 0.32 33 B 591D336X_6R3B2T 2.1 6 0.800 0.32 33 C 591D336X_6R3C2T 2.1 6 0.200 0.74 47 C 591D476X_6R3C2T 3.0 6 0.200 0.74 47 D 591D476X_6R3D2T 3.0 6 0.140 1.04 68 D 591D686X_6R3D2T 4.0 6 0.130 1.07 68 R 591D686X_6R3R2T 4.0 6 0.110 1.22 100 B 591D107X_6R3B2T15H 6.0 8 0.5 0.41 100 C 591D107X_6R3C2T 6.0 8 0.19 0.76 100 D 591D107X_6R3D2T 6.0 8 0.13 1.07 100 R 591D107X_6R3R2T 6.0 8 0.100 1.28 150 D 591D157X_6R3D2T 9.5 8 0.12 0.88 150 R 591D157X_6R3R2T 9.5 8 0.14 1.08 150 U 591D157X_6R3U2T 9.5 8 0.080 1.17 220 R 591D227X_6R3R2T 13.9 8 0.15 1.05 220 V 591D227X_6R3V2T 13.9 8 0.065 1.47 220 U 591D227X_6R3U2T 13.9 8 0.075 1.21 330 W 591D337X_6R3W2T 20.8 8 0.045 1.97 330 V 591D337X_6R3V2T 20.8 8 0.060 1.52 330 U 591D337X_6R3U2T 20.8 8 0.07 1.25 470 U 591D477X_6R3U2T 29.6 10 0.060 1.35 470 W 591D477X_6R3W2T 29.6 10 0.045 1.97 470 V 591D477X_6R3V2T 29.6 10 0.085 1.28 680 W 591D687X_6R3W2T 42.8 10 0.060 1.87

6.3 WVDC @ + 85

°C, SURGE = 8 V . . . 4 WVDC @ + 125°C, SURGE = 5 V

www.vishay.com 591D Vishay Sprague Document Number 40012 Revision 22-Nov-04 For technical questions, contact tantalum@vishay.com STANDARD / EXTENDED RATINGS CAPACITANCE (µF) CASE CODE PART NUMBER** Max. DCL @ + 25°C (µA) Max. DF @ + 25°C 120 Hz (%) Max. ESR @ + 25°C 100kHz (Ohms) Max. RIPPLE 100kHz Irms (Amps) * Preliminary values contact factory for availability. For 10% tolerance, specify "9"; for 20% tolerance, change to "0". Extended ratings are in bold print. Denotes 1.8mm maximum height. 10 WVDC @ + 85°C, SURGE = 13 V . . . 7 WVDC @ + 125°C, SURGE = 8 V 16 WVDC @ + 85°C, SURGE = 20 V . . . 10 WVDC @ + 125°C, SURGE = 12 V 10 A 591D106X_010A2T 1.0 6 1.300 0.24 10 B 591D106X_010B2T 1.0 6 0.850 0.31 22 B 591D226X_010B2T 2.2 6 0.800 0.32 22 C 591D226X_010C2T 2.2 6 0.200 0.74 33 C 591D336X_010C2T 3.3 6 0.200 0.74 33 D 591D336X_010D2T 3.3 6 0.140 1.04 47 D 591D476X_010D2T 4.7 6 0.140 1.04 47 R 591D476X_010R2T 4.7 6 0.120 1.17 68 C 591D686X_010C2T 6.8 6 0.190 0.76 68 D 591D686X_010D2T 6.8 6 0.130 1.15 68 R 591D686X_010R2T 6.8 6 0.110 1.22 100 D 591D107X_010D2T 10.0 8 0.130 1.07 100 U 591D107X_010U2T 10.0 8 0.085 1.13 150 V 591D157X_010V2T 15.0 8 0.075 1.37 150 U 591D157X_010U2T 15.0 8 0.080 1.17 220 W 591D227X_010W2T 22.0 8 0.055 1.78 220 V 591D227X_010V2T 22.0 8 0.065 1.47 330 W 591D337X_010W2T 33.0 8 0.050 1.87 330 W 591D337X_010W2T007 33.0 8 0.050 1.87 4.7 A 591D475X_016A2T 0.8 6 1.750 0.19 6.8 A 591D685X_016A2T 1.1 6 1.750 0.19 10 B 591D106X_016B2T 1.6 6 0.800 0.32 10 C 5910106X_016C2T 1.6 6 0.500 0.45 15 D 591D156X_016D2T 2.4 6 0.250 0.77 22 C 591D226X_016C2T 3.5 6 0.240 0.67 22 D 591D226X_016D2T 3.5 6 0.180 0.91 33 C 591D336X_016C2T 5.3 6 0.250 0.66 33 D 591D336X_016D2T 5.3 6 0.170 0.94 33 R 591D336X_016R2T 5.3 6 0.140 1.08 47 R 591D476X_016R2T 7.5 6 0.130 1.12 47 U 591D476X_016U2T 7.5 6 0.180 0.78 68 V 591D686X_016V2T 10.9 6 0.080 1.32 68 U 591D686X_016U2T 10.9 6 0.100 1.05 100 V 591D107X_016V2T 16.0 8 0.075 1.37 150* W* 591D157X_016W2T* 24.0* 8* 0.060* 1.71* 4.7 A 591D475X_020A2T 0.9 6 1.900 0.18 4.7 B 591D475X_020B2T 0.9 6 1.600 0.22 6.8 B 591D685X_020B2T 1.4 6 1.600 0.22 6.8 C 591D685X_020C2T 1.4 6 0.400 0.52 10 B 591D106X_020B2T 2.0 6 1.500 0.23 10 D 591D106X_020D2T 2.0 6 0.270 0.75 15 C 591D156X_020C2T 3.0 6 0.300 0.60 15 R 591D156X_020R2T 3.0 6 0.180 0.91 22 D 591D226X_020D2T 4.4 6 0.200 0.87 22 R 591D226X_020R2T 4.4 6 0.140 1.09 22* V* 591D226X_020V2T* 4.4* 6* 0.150* 0.90* 22* U* 591D226X_020U2T* 4.4* 6* 0.375* 0.54* 33 R 591D336X_020R2T 6.6 6 0.140 1.08 33* V* 591D336X_020V2T* 6.6* 6* 0.200* 0.73* 20 WVDC @ + 85°C, SURGE = 26 V . . . 13 WVDC @ + 125°C, SURGE = 16 V

www.vishay.com 591D Vishay Sprague Document Number 40012 Revision 22-Nov-04 For technical questions, contact tantalum@vishay.com TYPICAL CURVES OF ESR - AS A FUNCTION OF FREQUENCY 100 1kHz 10kHz 100kHz 1MHz 10MHz 591D 150 - 10V U CASE ESR/IMPEDANCE VS FREQUENCY OHMS 10.00 1.00 0.10 0.01 0.00 IMPEDANCE ESR 100 1kHz 10kHz 100kHz 1MHz 10MHz 10.00 1.00 0.10 0.01 0.00 FREQUENCY IN HERTZ 591D 330 - 6.3V V CASE ESR/IMPEDANCE VS FREQUENCY OHMS IMPEDANCE ESR 10.00 1.00 0.10 0.01 FREQUENCY IN HERTZ OHMS 591D 470 - 6.3V W CASE ESR/IMPEDANCE VS FREQUENCY 100 1kHz 10kHz 100kHz 1MHz 10MHz IMPEDANCE ESR 35 WVDC @ + 85°C, SURGE = 46 V . . . 23 WVDC @ + 125°C, SURGE = 28 V 25 WVDC @ + 85°C, SURGE = 33 V . . . 17 WVDC @ + 125°C, SURGE = 20 V STANDARD / EXTENDED RATINGS CAPACITANCE (µF) CASE CODE PART NUMBER** Max. DCL @ + 25°C (µA) Max. DF @ + 25°C 120 Hz (%) Max. ESR @ + 25°C 100kHz (Ohms) Max. RIPPLE 100kHz Irms (Amps) FREQUENCY IN HERTZ 2.2 A 591D225X_025A2T 0.6 6 5.000 0.11 2.2 B 591D225X_025B2T 0.6 6 3.800 0.15 3.3 B 591D335X_025B2T 0.8 6 3.700 0.15 3.3 C 591D335X_025C2T 0.8 6 1.000 0.32 4.7 C 591 D475X_025C2T 1.2 6 0.800 0.37 6.8 C 591D685X_025C2T 1.7 6 0.750 0.38 6.8 D 591D685X_025D2T 1.7 6 0.650 0.48 10 D 591D106X_025D2T 2.5 6 0.600 0.50 10 R 591D106X_025R2T 2.5 6 0.240 0.83 15 R 591D156X_025R2T 3.8 6 0.200 0.91 15* U* 591D156X_025U2T* 3.8* 6* 0.250* 0.66* 22* V* 591D226X_025V2T* 5.5* 6* 0.200* 0.84* 33* V* 591D336X_025V2T* 6.0* 6* 0.200* 0.84*

68 R 591D686X_025R2T20H** 17 8

• Preliminary values contact factory for availability. For 10% tolerance, specify "9"; for 20% tolerance, change to "0". Extended ratings are in bold print. ** XYH indicates maximum height in (mm) ie. 2.0mm max. (H) = 20Hmm 1 A 591D105X_035A2T 0.5 4 5.000 0.11 1 B 591D105X_035B2T 0.5 4 4.400 0.13 2.2 B 591D225X_035B2T 0.8 6 4.000 0.14 2.2 C 591D225X_035C2T 0.8 6 2.000 0.22 3.3 B 591D335X_035B2T 1.2 6 3.500 0.15 3.3 C 591D335X_035C2T 1.2 6 1.900 0.23 3.3 D 591D335X_035D2T 1.2 6 1.500 0.32 4.7 R 591 D475X_035R2T 1.6 6 0.750 0.47 6.8 D 591D685X_035D2T 2.4 6 0.950 0.40 6.8 R 591D685X_035R2T 2.4 6 0.750 0.47 10 R 591D106X_035R2T 3.5 6 0.600 0.52

www.vishay.com 591D Vishay Sprague Document Number 40012 Revision 22-Nov-04 For technical questions, contact tantalum@vishay.com FREQUENCY IN HERTZ 100 1K 10K 100K 1M 10M 100 0.1 0.01 "R" Case OHMS "C" Case FREQUENCY IN HERTZ 100 1K 10K 100K 1M 10M OHMS OHMS "D" Case FREQUENCY IN HERTZ TYPICAL CURVES @ + 25°C, IMPEDANCE AND ESR VS FREQUENCY "A" Case 1000 100 0.1 100 1K 10K 100K 1M 10M FREQUENCY IN HERTZ FREQUENCY IN HERTZ OHMS "B" Case OHMS IMPEDANCE ESR 15µF, 6.3 VDC 1µF, 35 VDC 1000 100 0.1 100 1K 10K 100K 1M 10M IMPEDANCE ESR 4.7µF, 20 V 10µF, 10 V 100 0.1 0.01 IMPEDANCE ESR 6.8µF, 25 V 47µF, 6.3 V IMPEDANCE ESR 4.7µF, 25 V 33µF, 6.3 V 1000 100 0.1 100 1K 10K 100K 1M 10M 10µF, 25 V IMPEDANCE ESR 100µF, 6.3 V

www.vishay.com 591D Vishay Sprague Document Number 40012 Revision 22-Nov-04 For technical questions, contact tantalum@vishay.com 2. DC Working Voltage: The DC working voltage is the maximum operating voltage for continuous duty at the rated temperature. 3. Surge Voltage: The surge DC rating is the maximum voltage to which the capacitors may be subjected under any conditions, including transients and peak ripple at the highest line voltage.

3.1 Surge Voltage Test: Capacitors shall withstand

the surge voltage applied in series with a 33 ohm ± 5% resistor at the rate of one-half minute on, one-half minute off, at + 85°C, for 1000 successive test cycles.

3.2 Following the surge voltage test, the dissipation

factor and the leakage current shall meet the initial requirements; the capacitance shall not have changed more than ± 10%. 4. Capacitance Tolerance : The capacitance of all capacitors shall be within the specified tolerance limits of the normal rating.

4.1 Capacitance measurements shall be made by means

of polarized capacitance bridge. The polarizing voltage shall be of such magnitude that there shall be no reversal of polarity due to the AC component. The maximum voltage applied to capacitors during measurement shall be 2 volts rms at 120 Hz at +25°C. If the AC voltage applied is less than one-half volt rms, no DC bias is required. Accuracy of the bridge shall be within ± 2%. 5. Capacitance Change With Temperature : The capacitance change with temperature shall not exceed the following percentage of the capacitance measured at + 25°C: + 85°C Rating + 125°C Rating Working Voltage (V) Working Voltage (V) Surge Voltage (V) Surge Voltage (V) 6.3 5.2 2.7 3.4 - 55°C - 10% + 85°C + 10% + 125°C + 12% PERFORMANCE CHARACTERISTICS 1. Operating Temperature: Capacitors are designed to operate over the temperature range - 55°C to + 85°C.

1.1 Capacitors may be operated to + 125°C with

voltage derating to two-thirds the + 85°C rating. 6. Dissipatior Factor: The dissipatior factor, determined from the expression 2πRC, shall not exceed values listed in the Standard Ratings Table.

6.1 Measurements shall be made by the bridge method

at, or referred to, a frequency of 120Hz and a temperature of + 25°C. 7. Leakage Current: Capacitors shall be stabilized at the rated temperature for 30 minutes. Rated voltage shall be be applied to capacitors for 5 minutes using a steady source of power (such as a regulated power supply) with 1000 ohm resistor connected in series with the capacitor under test to limit the charging current. Leakage current shall not then be measured. Note that the leakage current varies with temperature and applied voltage. See graph below for the appropriate adjustment factor Leakage Current Factor TYPICAL LEAKAGE CURRENT FACTOR RANGE 100 1.0 0.1 0.01 0.001 0 10 20 30 40 50 60 70 80 90 100 + 125°C + 85°C + 55°C + 25°C 0°C - 55°C Percent of Rated Voltage

www.vishay.com 591D Vishay Sprague Document Number 40012 Revision 22-Nov-04 For technical questions, contact tantalum@vishay.com P = Power Dissipation in Watts @ + 25°C as given in the table in Paragraph Number 6.0 (Power Dissipation) RESR = The capacitor Equivalent Series Resistance at the specified frequency. 3. A-C Ripple Voltage: The maximum allowable ripple voltage shall be determined from the formula: or, from the formula: where, P = Power Dissipation in Watts @ + 25°C as given in the table in Paragraph Number 6.0 (Power Dissipation). R ESR = The capacitor Equivalent Series Resistance at the specified frequency.

7.1 At + 25 °C, the leakage current shall not exceed

the value listed in the Standard Ratings Table.

7.2 At + 85 °C, the leakage current shall not exceed 10

times the value listed in the Standard Ratings Table.

7.3 At + 125 °C, the leakage current shall not exceed

12 times the value listed in the Standard Ratings Table. 8. Equivalent Series Resistance: Measurements shall be made by the bridge method at, or referred to, a frequency of 100 KHz and a temperature of + 25°C.

8.1 The Equivalent Series Resistance shall not exceed the

value listed in the Standard Ratings Table. 9. Life Test: Capacitors shall withstand rated DC voltage applied at + 85°C for 2000 hours or derated DC voltage applied at + 125°C for 1000 hours.

9.1 Following the life test, the dissipation factor and

leakage shall meet the initial requirement; the capacitance change shall not exceed ± 10% of the initial value.

10 Humidity Test: Capacitors shall withstand 1000 hours

at + 40°C, 90% to 95% relative humidity, with no voltage applied

10.1 Following the humidity test, capacitance change shall

not exceed ± 10% of the initial value, dissipation factor shall not exceed 150% of the initial requirement; leakage currrent shall not exceed 200% of the initial requirement at + 25°C 11. Solderability: Capacitors will meet the solderability requirements of ANSI/J-STD-002, test B category 1. PERFORMANCE CHARACTERISTICS (Continued) 12. Resistance to Soldering Heat: Capacitors mounted on a substrate will withstand + 260°C for 5 seconds.

12.1 Following the resistance to soldering heat test,

capacitance, dissipation factor and DC leakage current shall meet the initial requirement. 13. Marking: The small body area of these capacitors does not allow elaborate marking schemes. All required information is present on the carton or package in which the parts are shipped; in addition, part number, quantity and data code are indicated on the reels. 14. Terminal Strength: Per IEC-384-3, minimum of 5N shear force. 15. Environmental: Mercury, CFC and ODS materials are not used in the manufacture of these capacitors. 16. Flammability: Encapsulant materials meet UL94 V0 17. Capacitor Failure Mode: The predominant failure mode for solid tantalum capacitors is increased leakage current resulting in a shorted circuit. Capaci- tor failure may result from excess forward or reverse DC voltage, surge current, ripple current, thermal shock or excessive temperature. The increase in leakage is caused by a breakdown of the Ta 2O5 dielectric. For additional information on leakage failure of solid tantalum chip capacitors, refer to Vishay Sprague Technical Paper, “Leakage Failure Mode in Solid Tantalum Chip Capacitors.” P RESRIrms = Vrms = Irms x Z P RESR Vrms = Z GUIDE TO APPLICATION

1.0 Recommended rated working voltage guidelines:

(-55°C to + 85°C) Application Voltage Recommended Capacitor (V) Voltage Rating (V) 2.5 4 4 6.3 61 0 10 16 12 20 18 25 2. A-C Ripple Current: The maximum allowable ripple current shall be determined from the formula: where,

www.vishay.com 591D Vishay Sprague Document Number 40012 Revision 22-Nov-04 For technical questions, contact tantalum@vishay.com 6. Printed Circuit Board Materials : The capacitors are compatible with most commonly used printed circuit board materials (alumina substrates, FR4, FR5, G10, PTFE-fluorocarbon and porcelanized steel). If your desired board material is not shown there please contact the Tantalum Marketing Department for assistance in determining compatibility. 7. Attachment:

7.1 Solder Paste: The recommended thickness of the

solder paste after application is 0.007" ± 0.001" [0.178mm ± 0.025mm]. Care should be exercised in selecting the solder paste. The metal purity should be as high as practical. The flux (in the paste) must be active enough to remove the oxides formed on the metallization prior to the exposure to soldering heat.

7.2 Soldering: Capacitors can be attached by

conventional soldering techniques - convection, infrared reflow, wave soldering and hot plate methods. The Soldering Profile chart shows typical recomended time/temperature conditions for soldering. Attachment with a soldering iron is not recommended due to the difficulty of controlling temperature and time at temperature. The soldering iron must never come in contact with the capacitor. 5. Power Dissipation : Power dissipation will be affected by the heat sinking capability of the mounting surface. Non-sinusoidal ripple current may produce heating effects which differ from those shown. It is important that the equivalent Irms value be established when calculating permissible operating levels. (Power dissipation calculated using + 25°C temperature rise.)

7.1 Recommended Mounting Pad Geometries: The

nib must have sufficient clearance to avoid electrical contact with other components. The width dimension indicated is the same as the maximum width of the capacitor. This is to minimize lateral movement. 8. Cleaning (Flux Removal) After Soldering: The capacitors are compatible with all commonly used solvents such as TES, TMS, Prelete, Chlorethane, Terpene and aqueous cleaning media. Solvents containing methylene chloride or other epoxy solvents should be avoided since these will attack the epoxy encapsulation material. Case Code Maximum Permissible Power Dissipation @ + 25°C (Watts) in free air A B C D R U V W 0.075 0.085 0.110 0.150 0.165 0.110 0.140 0.175 Temperature Derating Factor + 25°C + 85°C + 125°C 1.0 0.9 0.4

4.0 Reverse Voltage: These capacitors are capable of

withstanding peak voltages in the reverse direction equal to 10% of the DC rating or 1 volt maximum at + 25°C and 5% of the DC voltage rating or 0.5 volt maximum at + 85°C.

5.0 Temperature Derating : If these capacitors are to be

operated at temperatures above + 25°C, the permissible rms ripple current or voltage shall be calculated using the derating factors as shown: * Pads for B, C and D case codes are otherwise pad compatible with * Type 293D, B, C and D case codes respectively. REFLOW SOLDER PADS* in inches [millimeters] A B B C CASE WIDTH PAD SEPARATION CODE (A) METALIZATION (C) A 0.083 0.067 0.050 [2.1] [1.7] [1.3] B 0.138 0.067 0 .067 [3.5] [1.7] [1.7] C 0.138 0.090 0.127 [3.5] [2.3] [3.1] D 0.180 0.090 0.145 [4.6] [2.3] [3.7] R 0.322 0.090 0.145 [8.1] [2.3] [3.7] U 0.138 0.090 0.122 [3.5] [2.3] [3.1] V 0.180 0.090 0.145 [4.6] [2.3] [3.7] W 0.327 0.090 0.145 [8.3] [2.3] [3.7] 250 200 150 100 TIME (SECONDS) TEMPERATURE DEG. CENTIGRADE0 50 100 150 200 250 300 350 RECOMMENDED REFLOW SOLDERING PROFILE GUIDE TO APPLICATION

www.vishay.com 591D Vishay Sprague Document Number 40012 Revision 22-Nov-04 For technical questions, contact tantalum@vishay.com Units Per Reel 13" [330] Reel 7" [178] Reel Component Pitch Tape Width Case Code Embossment Carrier Top Cover Tape Thickness Standard orientation is with the cathode (-) nearest to the sprocket holes per EIA-481-1 and IEC 286-3. TAPE AND REEL PACKAGING Bending Radius (Note 2) R Min. A 8mm 4mm 2500 10,000 B 12mm 4mm 2000 8000 C 12mm 8mm 1000 4000 D 12mm 8mm 1000 4000 R 12mm 8mm 1000 4000 U 12mm 8mm 1000 4000 V 12mm 8mm 1000 4000 W 12mm 8mm 1000 2500

www.vishay.com 591D Vishay Sprague Document Number 40012 Revision 22-Nov-04 For technical questions, contact tantalum@vishay.com Notes: 1. A 0B0K0 are determined by the maximum dimensions to the ends of the terminals extending from the component body and/or the body dimensions of the component. The clearance between the ends of the terminals or body of the component to the sides and depth of the rotation of the component within the cavity of not more than 20 degrees. 2. Tape with components shall pass around radius "R" without damage. The minimum trailer length may require additional length t o provide R minimum for 12mm embossed tape for reels with hub diameters approaching N minimum. 3. This dimension is the flat area from the edge of the sprocket hole to either the outward deformation of the carrier tape betw een the embossed cavities or to the edge of the cavity whichever is less. 4. This dimension is the flat area from the edge of the carrier tape opposite the sprocket holes to either the outward deformati on of the carrier tape between the embossed cavity or to the edge of the cavity whichever is less. 5. The embossment hole location shall be measured from the sprocket hole controlling the location of the embossment. Dimensions of embossment location and hole location shall be applied independent of each other. 6. B 1 dimension is a reference dimension for tape feeder clearance only. TAPE AND REEL PACKAGING in inches [millimeters] Please Note: Metric dimensions will govern. Dimensions in inches are rounded and for reference only. 8mm 12mm 12mm Double Pitch TAPE SIZE 0.179 [4.55] 0.323 [8.2] 0.323 [8.2] B 1 (Max.) (Note 6) 0.039 [1.0] 0.059 [1.5] 0.059 [1.5] D1 (Min.) (Note 5) 0.138 ± 0.002 [3.5 ± 0.05] 0.217 ± 0.002 [5.5 ± 0.05] 0.453 ± 0.004 [11.5 ± 0.03] F A0 B0 K0 0.315 + 0.012 - 0.004 [8.0 + 0.3 - 0.1] 0.472 ± 0.012 [12.0 ± 0.30] 0.945 ± 0.012 [24.0 ± 0.03] W 0.098 [2.5] 0.256 [6.5] 0.256 [6.5] (Max.) 0.984 [25.0] 1.181 [30.0] 1.181 [30.0] R (Min.) (Note 2)P1 (Note 1) 0.157 ± 0.004 [4.0 ± 0.10] 0.157 ± 0.004 [4.0 ± 0.10] 0.315 ± 0.004 [8.0 ± 0.10] Tape and Reel Specifications: All case sizes are available on plastic embossed tape per EIA-481-1. Tape reeling per IEC 286-3 is also available. Standard reel diameter is 7" [178mm]. 13" [330mm] reels are available and recommended as the most cost effective packaging method. The most efficient packaging quantities are full reel increments on a given reel diameter. The quantities shown allow for the sealed empty pockets required to be in conformance with EIA-481-1. Reel size and packaging orientation must be specified in the Vishay Sprague part number. Camber (Top View) Allowable Camber to be .039/3.937 [1/100] Non-Cumulative Over 9.843 [250.0] .039 [1.0] Max. Tape (Top View) USER DIRECTION OF FEED .030 [0.75] Min. (Note 3) Center Lines of Cavity .030 [0.75] Min. (Note 4) Top Cover Tape .059 + .004 - 0.0 [1.5 + 0.10 - 0.0] Deformation Between Embossments Embossment Maximum Cavity Size (Note 1) .079 ± .002 [2.0 ± 0.05] .157 ± .004 [4.0 ± 0.10] F .069 ± .004 [1.75 ± 0.10]

10 Pitches Cumulative

± 0.008 [0.200] 20° Maximum Component Rotation .039 [1.0] Max. 9.843 [250.0] 3.937 [100.0] Top Cover Tape D1 Min. For Components (Note 5) Max. .024 [0.600] Max. B1 Max. (Note 6) .004 [0.10] Max. For Tape Feeder Reference only including draft. Concentric around B0 (Note 5) Typical Component Cavity Center Line Typical Component Center Line W (Side or Front Sectional View) Maximum Component Rotation 20° DIRECTION OF FEED Cathode (-) Anode (+)