DATASHEET SEARCH SITE | WWW.ALLDATASHEET.COM
Document overview
- Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
- PDF pages: 4
Technical content
Instruction SheetPRO- CRIMPER* III Hand Crimping Tool Assembly 58663- 1 and Die Assembly 408- -4476 LOC B 1 of 4E2009 Tyco Electronics Corporation, Harrisburg, PA All International Rights Reserved TE logo and Tyco Electronics are trademarks. *Trademark. Other products, logos, and company names used are the property of their respective owners. TOOLING ASSISTANCE CENTER 1- -800- -722- -1111 PRODUCT INFORMATION 1- -800- -522- -6752 This controlled document is subject to change. For latest revision and Regional Customer Service, visit our website atwww.tycoelectronics.com
17 DEC 09 Rev B58663- 2 For Series F Coaxial Connectors
Cumulative Trauma Disorders can result from the prolonged use of manually powered hand tools. Hand tools are intended for occasional use and low volume applications. A wide selection of powered application equipment for extended- -use, production operations is available. Figure 1 The PRO- -CRIMPER III Hand Crimping Tool is a “Commercial” grade tool and is designed primarily for field installation, repair, maintenance work, or prototyping in industrial, commercial, or institutional applications. Product crimped with this tool will meet the crimp height requirement for hand tools in the appropriate 114 series specification, but may not comply with other feature parameters of the specification. Tyco Electronics offers a variety of tools to satisfy your performance requirements. For additional information, contact the Tooling Assistance Center at 1 - -800 - -722 - -1111. Die Assembly 58663- -2 Moving Jaw Ratchet Adjustment Wheel Moving Handle Stationary Handle PRO- -CRIMPER III Hand Crimping Tool Frame Pivot Pin Back of Tool (Wire Side) Stationary Jaw 1. INTRODUCTION PRO- -CRIMPER III Hand Crimping Tool Assembly 58663- -1 consists of Die Assembly 58663- -2 and PRO- -CRIMPER III Hand Crimping Tool Frame 354940- -1. The tool is designed to crimp Series F coaxial connectors onto cable Series 6 Quad. Dimensions on this sheet are inmillimeters [with inch equivalents in brackets]. Figures and illustrations are for identification only and are not drawn to scale. For additional information on the hand tool frame, refer to 408- -9930. For the selection of Series F coaxial connectors, contact AMP Product Engineering for connector recommendations. Reasons for reissue of this instruction sheet are provided in Section 8, REVISION SUMMARY. 2. DESCRIPTION(Figure 1) The tool features a tool frame with a stationary jaw and handle, a moving jaw, a moving handle, and an adjustable ratchet that ensures full connector crimping. The tool frame holds the die assembly. The die assembly features an anvil and a nest containing a hex crimping cavity. Each die is held in the hand tool by a single screw. 3. INSTALLATION AND REMOVAL OF THE DIE ASSEMBLY(Figure 2) 1. Open the tool handles and remove the two die retaining screws from the tool jaws. 2. Slide the die assembly into the partially opened tool jaws. 3. Insert the die retaining screws and tighten the screws just enough to hold the dies in place. Do not tighten the screws completely at this time. NOTE i
408- 4476PRO- CRIMPER III Hand Crimping Tool Assembly 58663- 1 for Series F Coaxial Connectors Rev B4 of 4 Tyco Electronics Corporation Figure 6 PRO-CRIMPER III Hand Tool 354940-1 (Instruction Sheet 408- 9930) SDE-SA Hand Tool 9-1478240-0 (Instruction Sheet 408- 8851) SDE Bench Terminator 1490076- 2 (Customer Manual 409- 10052)
626 Adapter 679304- 1
(Instruction Sheet 408- 4070) Battery Tool (Shouldered Die) 1725837-1, -2 (Customer Manual 409- 10053) Battery Tool (Pin/Shoulder Die) 1213890-1, -2 (Customer Manual 409- 10065) Since crimped splices cannot be removed from this tool,DO NOT crimp splices in this battery tool. NOTE i