5711

5710 BITECH | Alldatasheet

Document overview

• Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
• PDF pages: 4

Technical content

3” Diameter Single Turn Wirewound Precision Potentiometer ELECTRICAL Resistance Range, Ohms 25 to 145K Standard Resistance Tolerance ±5% Minimum Practical Resistance Tolerance ±1% Independent Linearity ±0.5% Minimum Practical Independent Linearity ±0.5%, <75 Ohms ±0.075%, ≥7K Ohms Power Rating, Watts 5.0 at 40°C derating to 0 at 105°C Dielectric Strength 1,000V rms Insulation Resistance, Minimum 1,000 Megohms Noise, Maximum 100 Ohms Actual Electrical Travel 358° ±1° Tap Tolerance ±1° End Voltage, Maximum Within Std. Linearity Tolerance ENVIRONMENTAL (MIL-R-12934) MODEL STYLES 5711 1/4" Shaft, 1/2" Bushing 5713 1/4" Shaft, Servo Operating Temperature Range Static: –65°C to +105°C Dynamic: -40°C to +125°C Temperature Cycling 5 cycles, –65°C to +105°C Shock, 6ms Half Sine 100G’s Vibration 5G’s, 10 to 500 Hz Moisture Ten 24 hour cycles High Temperature Exposure 1,000 hours at 105°C Rotational Life 1 Mil. Shaft Rev. Rotational Load Life 1 mil. shaft rev. plus 900 hrs. at rated wattage at 40°C Specifications subject to change without notice.

STANDARD RESISTANCE VALUES, OHMS Theoretical Total Resolution Tempco Resistance (% Nominal) of Wire 1K 0.062 ±130 ppm/°C 2K 0.050 ±130 ppm/°C 5K 0.038 ±130 ppm/°C 10K 0.031 ±130 ppm/°C 20K 0.027 ±130 ppm/°C 50K 0.024 ± 20 ppm/°C 100K 0.022 ± 20 ppm/°C 2-56 Model 5710 Series MECHANICAL Total Mechanical Travel 360° Continuous Number of Cups, Maximum 4 Weight, Nominal 5.8 oz. Single Cup 1.3 oz. Each Added Cup Backlash, Maximum 1° Shaft End Play, Maximum .005” 5711 5713 Shaft Radial Play, Maximum .004” .002” METRIC CONVERSIONS 1 in. 25.4 mm 1 oz. 28.4 gm 1 oz.-in. 0,007 N-m 1 lb.-in. 0,113 N-m

OUTLINE DIMENSIONS (Inch/mm) 1.750 44.45R. Max. 90˚Max. CCW Slider CWClamp Ears 2.785 73.03 1.520± .031 38.61± 0.79 1.020± .015 25.91± 0.38 Mounting Surface + .0000 – .0003 + 0.000 – 0.008 .2497 6.342 .625± .031 15.9± 0.79 Dia. Dia. Dia. Max. .073 1.85Min. + .000 – .001 + 0.00 – 0.03 2.875 73.03 Dia. 3.000± .005 76.20± 0.13Dia. 3.000± .016 76.20± 0.41 .062± .005 1.58± 0.13 .093± .005 2.36± 0.13 “RS” “L” .500 12.7 Min. .562± .002 14.3± 0.05 .562 14.3 Dimensions shown are with 1 cup, for each additional cup: increase “RS” by increase “L” by Chamfer .016 0.41 Max. x 45˚ OUTLINE DIMENSIONS (Inch/mm) 1.750 44.45R. Max. Positioned as shown ± 5˚ Locating Hole 90˚Max. CCW Slider CWClamp Ears .531± .016 13.5± 0.41 .129± .005 1.58± 0.41Deep 1.500± .031 38.10± 0.79 1.375± .016 34.93± 0.41 .500± .016 12.7± 0.41 1.482± .031 37.64± 0.79 .982± .020 24.9± 0.51 Mounting Surface + .0000 – .0003 + 0.000 – 0.008 .2497 6.342 + .000 – .010 + 0.00 – 0.25 .062 1.58 Dia. Dia. + .0000 – .0020 + 0.000 – 0.051 .5937 15.08 Dia. Dia.3.000± .016 76.20± 0.41 “RS ” “L” .469 11.9 1/2-32 NS Thread Chamfer .016 0.41 Min. .562± .002 14.3± 0.05 .562 14.3 Dimensions shown are with 1 cup, for each additional cup: increase “RS ” by increase “L” by Max. x 45˚ + + Model 5711 - Bushing Mount Model 5713 - Servo Mount

ORDERING INFORMATION

5711 R 10K L.50 XX Model Series Resistance Prefix Resistance Value Optional Special Feature Code Linearity (CCW) (S) (CW) Metric equivalents, based on 1 inch = 25.4mm are rounded to the same number of significant figures as in the original English units and are provided for general information only. Tolerances unless otherwise specified: Linear = ± .01 inches (.25mm) Angular = ± 2 degrees NOTES mm INCH CIRCUIT DIAGRAM SPECIAL FEATURES Center Tap CT Linearity Tape LT Rear Shaft Extension RS Flatted Shaft FS Slotted Shaft SS Anti-Fungus Treatment AF