5690 ADAFRUIT | Alldatasheet
Document overview
- Manufacturer or author: Provided By alldatasheet.com(free datasheet download site)
- PDF pages: 3
Technical content
Adafruit ATtiny]1616 Breakout with seesaw —- STEMMA QT / Qwiic Product ID: 5690 | CP9QQOOQ0000@ a SFL Pee eae = ee wo tm at yas tus : Se @09000000000w! « EPUPERUREU BEDE
Description
This breakout board is a "three in one" product:
- The ATtiny1616 is part of the 'next gen' of AVR microcontrollers, and now we have a cute development/breakout board for it, with just enough hardware to get the chip up and running. 2. It's also an Adafruit seesaw board. Adafruit seesaw is a near-universal converter framework which allows you to add and extend hardware support to any I2C- capable microcontroller or microcomputer. Instead of getting separate I2C GPIO expanders, ADCs, PWM drivers, etc, seesaw can be configured to give a wide range of capabilities. 3. Finally, with STEMMA QT connectors on it, you could use it as either an I2C controller or peripheral with plug-and play support. We primarily designed this board for our own use: it's a mini dev board that lets us design with the ATtiny1616 just like we did for the ATSAMDO9. With the 2021- 2022 silicon shortage, we're adapting some of our SAMDO9 designs to the ATTiny8xx series and wanted a quick minimal board to test code on. Each breakout comes with the assembled and tested board, as well as some header strips. Each PCB is fairly minimal and contains: e« ATtiny1616 8-bit microcontroller ¢ 16KB flash, 2KB of RAM, 256 bytes of EEPROM ¢ Internal oscillator can run up to 20MHz e Internal hardware multiplier « Can run from 2V to 5V power/logic (check the datasheet for max speed at desired power) e 3.3V regulator - by default we run at the Vin voltage, which can be 5V, but there's a solder jumper on the bottom if you'd like to select 3V logic. e Green power LED e Red indicator LED e Two STEMMA QT I2C connectors with 10K pullup resistors, connected to pins 8 and 9 This board comes pre-programmed with seesaw peripheral code that will let it act as an "12C to something" converter, basically a little 12C-controlled friend to do all the timing-sensitive things many microcontrollers and microcomputers are not good at. For example, using this breakout with the pre-burned seesaw firmware gives you e 12x GPIO with selectable pullup resistors: 0-5, 6, 8,11, 14, 15, 16
e 9x 10-bit ADC inputs - pins 0, 1, 2, 3, 4,5, 14, 15, 16 « 5 x 8-bit PWM outputs - pins 0, 1, 7,11, 16 « 1x NeoPixel output (up to 250 pixels) «1x EEPROM with 127 byte of NVM memory (handy for storing small access tokens or MAC addresses) - last byte of EEPROM is used for I2C address selection « 1x Interrupt output that can be triggered by any of the accessories - pin 6 e 2.x 12C address selection pins - pins 12 and 13 « 1x Activity LED on pin 10, tied active low Of course, you can configure or reprogram the chip to however you want to use it - we like using SpenceKonde's megaTinyCore which brings Arduino peripheral support to this series of chips. To program the chip you will need a 'UPDI' programmer, which you can make with a USB-to-Serial cable and a single 4.7K or 10K resistor. Please note: The boards do not come with a bootloader. If you want to do development on seesaw (e.g. changing the configuration) you need a separate UPDI programming setup! The firmware we put on is available as this example sketch, compiled using the megaTinyCore. We don't provide any support for custom builds of seesaw - we think this is cool and useful for the Maker community! YouTube link: https: //www.youtube.com/watch?v=Uu0zQ95SWx8&embeds_euri=https%3A%2 F%2Fw ww.adafruit.com%2F&feature=emb_imp_woyt https: //www.youtube.com/watch?t=307&v=HobZxYg7r3M&embeds_euri=https%3A %2F%2Fwww.adafruit.com%2F&feature=emb_imp_woyt Technical Details FS 2015/863/EU. https://www.adafruit.com/product/5690 4-19-23