5613

5611 BITECH | Alldatasheet

Document overview

• Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
• PDF pages: 4

Technical content

2” Diameter Single Turn Wirewound Precision Potentiometer ELECTRICAL Resistance Range, Ohms 15 to 80K Standard Resistance Tolerance ±5% Minimum Practical Resistance Tolerance ±1.0% Independent Linearity ±1.0%, <50 Ohms ±0.5%, ≥50 Ohms Minimum Practical Independent Linearity ±1.0%, <50 Ohms ±0.5%, 50-499 Ohms ±0.1%, ≥5K Ohms Power Rating, Watts 3.5 at 70°C derating to 0 at 125°C Dielectric Strength 1,000V rms Insulation Resistance, Minimum 1,000 Megohms Noise, Maximum 100 Ohms Actual Electrical Travel 356° + 1° Tap Tolerance ±1° End Voltage, Maximum Linearity x Input Voltage ENVIRONMENTAL (MIL-R-12934) MODEL STYLES 5611 1/4" Shaft, 3/8" Bushing 5613 1/4" Shaft, Servo Specifications subject to change without notice. Operating Temperature Range Static: –65°C to +125°C Dynamic: –40°C to +125°C Temperature Cycling 5 cycles, -65°C to +125°C (10% ∆R) Shock, 6ms Sawtooth 50G’s (0.1ms discontinuity max.) Vibration 15G’s, 10 to 2,000 Hz (5% ∆R, 0.1ms discontinuity max.) Moisture Resistance Ten 24 hour cycles (3% ∆R) High Temperature Exposure 1,000 hours at 125°C (5% ∆R) Rotational Life 1 Mil. Shaft Rev. Rotational Load Life 1 mil. shaft rev. at rated wattage at 70°C (5% ∆R)

"RS" ±.031 ±0.79 Mounting Surface .875±.031 22.2±0.79 +.0000 -.0003 +0.000 -0.008 .2497 6.342 Dia. Dia. Dia. 1.375±.016 34.93±0.41 .375 9.53 Min. +.000 -.002 +0.00 -0.05 .406 10.3 Chamfer Max. x 45°.016 0.41 3/8 - 32 UNEF Thread .375±.016 9.53±0.41 +.000 -.010 +0.00 -0.25 .062 1.58 2.000±.016 50.80±0.41 Dia. "L" 90° Max. ClampEars CW CCW Slider 1.250 31.75 R. Max. .531±.016 13.5±0.41 R. Locating Hole Positioned as shown ± 5° Dia. x Deep .905±.020 1.405 22.9±0.51 35.69 1.467±0.22 1.967 37.26±0.56 49.96 2.029±.024 2.529 51.54±0.61 64.24 2.591±.026 3.091 65.81±0.66 78.51 Dim. "L" Dim. "RS" No. of Cups 2-52 Model 5610 Series MECHANICAL Total Mechanical Travel 360 ° Continuous Number of Gangs, Maximum 4 Weight, Nominal 3.7 oz. Single Gang 1.3 oz. Each Added Gang Backlash, Maximum 1° Shaft End Play, Maximum .005” 5611 5613 Shaft Radial Play, Maximum .004 ” .002” OUTLINE DIMENSIONS (Inch/mm) Model 5611 Bushing Mount with Sleeve Bearing

OUTLINE DIMENSIONS (Inch/mm) "RS" ±.031 ±0.79 Mounting Surface 2.000±.016 50.80±0.41 "L" Dia. .625±.031 15.9±0.79 .010 0.25 R. Max 2.000±.005 50.80±0.13 Dia.Dia. +.0000 -.0003 +0.000 -0.008 .2497 6.342 +.000 -.001 +0.00 -0.03 1.875 47.63 Chamfer Max. x 45°.016 0.41 .093±.005 2.36±0.13 .062±.005 1.58±0.13 .073 1.85 Min. 1.875 47.63 Dia. Max. .50 12.7 Min. 90° Max. Clamp Ears CW CCW Slider 1.250 31.75 R. Max. 1.020±.015 1.520 25.91±0.38 38.61 1.582±0.17 2.082 40.18±0.43 52.88 2.144±.019 2.644 54.46±0.48 67.16 2.706±.021 3.206 68.73±0.53 81.43 Dim. "L" Dim. "RS" No. of Cups 2-53 Model Series 5610 METRIC CONVERSIONS 1 in. 25.4 mm 1 oz. 28.4 gm 1 oz.-in. 0,007 N-m 1 lb.-in. 0,113 N-m Model 5613 Servo Mount with Ball Bearing

ORDERING INFORMATION

5611 R 10K T2 L .50 XX Model Series Resistance Prefix Resistance Value Optional Special Feature Code Linearity Optional Non-Standard Tolerance (CCW) (S) (CW) Metric equivalents, based on 1 inch = 25.4mm are rounded to the same number of significant figures as in the original English units and are provided for general information only. Tolerances unless otherwise specified: Linear = ± .01 inches (.25mm) Angular = ± 2 degrees NOTES mm INCH CIRCUIT DIAGRAM SPECIAL FEATURES Center Tap CT Linearity Tape LT Rear Shaft Extension RS Flatted Shaft FS Slotted Shaft SS Shaft Lock (5611 only) SL Additional Gangs 2G or 3G or 4G STANDARD RESISTANCE VALUES, OHMS Theoretical Total Resolution Tempco Resistance (% Nominal) of Wire 1K 0.089 *±130 ppm/ ° C 2K 0.071 *±130 ppm/ ° C 5K 0.058 ±20 ppm/ ° C 10K 0.053 ±20 ppm/ ° C 20K 0.043 ±20 ppm/ ° C 30K 0.040 ± 20 ppm/ ° C 50K 0.040 ± 20 ppm/ ° C * Lower tempco available as a non-standard model (consult factory).